2005 LEXUS LS430 length

00L260
PICTORIAL INDEX
xviii
SEAT AND STEERING WHEEL
1 Tilt and telescopic steering
adjustment switch 228
. . . . . . . . . . . . .
2 Seat cushion length
control switch 157
. . . . . . . . . . . . . . . . .
3 Seat position, seat cushion
angle and height control
switch 157, 159
. . . . . . . . . . . . . . . . . . . .
4 Seatback angle and head
restraint control switch 158, 165 . . . .
5 Lumbar support control
switches 159
. . . . . . . . . . . . . . . . . . . . . .
For detailed information, refer to the
description given in each section.

00L139
Seat adjustmentSeat
position
Seat cushion angle
Seat cushion height
Head restraint height
Seatback angle
Upper lumbar support
Head restraint angle
Lower lumbarsupport
Seat cushion
length
QUICK REFERENCE
2
1. DRIVER’S SEAT

OCCUPANT RESTRAINT SYSTEMS
156
Seat adjustment precautions
CAUTION
Do not adjust the seat while the vehicle is moving as
the seat may unexpectedly move and cause the
driver to lose control of the vehicle.
 Be careful that the seat does not hit a passenger,
luggage or the rear seat.
NOTICE
Do not operate the control switch in more than one
dimension at a time. It may cause electrical overload.
Adjusting front seats
16L257a
 1
Seat cushion length control switch
2 Seat position control switch, seat cushion angle
and height control switch
3Seatback angle and head restraint control switch
4Upper lumbar support control switch
5 Lower lumbar support control switch

OCCUPANT RESTRAINT SYSTEMS
157
Adjusting seat cushion length
16L264
For driver’s seat only
Move the control switch in the desired direction.
Releasing the switch will stop the seat cushion in that position.
Do not place anything under the seat, as this might interfere
with the seat movement.
Adjusting seat position
16L258a
 For driver’s seat
Move the control switch in the desired direction.
Releasing the switch will stop the seat and head restraint in
that position. Do not place anything under the seat, as this
might interfere with the seat movement.
You can adjust the head restraint in the desired position by
using the head restraint control switch. However, if you move
the seat more than 15 mm (0.6 in.) by using the seat position
control switch after adjusting the head restraint, the head
restraint will return to the designated position as determined by
the seat position switch. To adjust the head restraint, see
“Head restraints” on page 165.

OCCUPANT RESTRAINT SYSTEMS
170
Fastening front and rear seat belts
16L287
Adjust the seat as needed and sit up straight and well back
in the seat. To fasten your belt, pull it out of the retractor
and insert the tab into the buckle.
You will hear a click when the tab locks into the buckle.
The seat belt length automatically adjusts to your size and the
seat position.
The retractor will lock the belt during a sudden stop or on
impact. It also may lock if you lean forward too quickly. A slow,
easy motion will allow the belt to extend, and you can move
around freely. When a passenger’s shoulder belt is completely extended and
is then retracted even slightly,
the belt is locked in that position
and cannot be extended. This feature is used to hold the child
restraint system securely. (For details, see “Child restraint” on
page 199.) To free the belt again, fully retract the belt and then
pull the belt out once more.
If the seat belt cannot be pulled out of the retractor, firmly pull
the belt and release it. You will then be able to smoothly pull
the belt out of the retractor.
CAUTION
 After inserting the tab, make sure the tab and buckle
are locked and that the belt is not twisted.
 Do not insert coins, clips, etc. in the buckle as this
may prevent you from properly latching the tab and
buckle.
 If the seat belt does not function normally,
immediately contact your Lexus dealer. Do not use
the seat until the seat belt is fixed, because it cannot
protect an adult occupant or your child from injury.

OCCUPANT RESTRAINT SYSTEMS
173
CAUTION
Always make sure the shoulder belt is positioned
across the center of the child’s shoulder. The belt
should be kept away from the child’s neck, and should
not fall off the child’s shoulder. Failure to observe these
precautions could reduce the effectiveness of the seat
belt in an accident, causing death or serious injury.
Seat belt extender
If your seat belts cannot be fastened securely because they
are not long enough, a personalized seat belt extender is
available from your Lexus dealer free of charge.
Please contact your local Lexus dealer so that the dealer can
order the proper required length for the extender. Bring the
heaviest coat you expect to wear for proper measurement and
selection of length. Additional ordering information is available
at your Lexus dealer.
CAUTION
When using the seat belt extender, observe the
following precautions. Failure to follow these
instructions could reduce the effectiveness of the seat
belt restraint system in case of an accident, increasing
the chance of personal injury.
 Remember that the extender provided for you may
not be safe when used on a different vehicle, for
another person, or at a different seating position than
the one originally intended.

OCCUPANT RESTRAINT SYSTEMS
220
CAUTION
When using the lower anchorages for the child
restraint system, be sure that there are no irregular
objects around the anchorages or that the seat belt is
not caught.
 Push and pull the child restraint system in different
directions to be sure it is secure. Follow all the
installation instructions provided by its
manufacturer.
 When using the lower anchorages for a child restraint
system, ensure that the seat is moved to the
rearmost position, with the seatback close to the
child restraint system.
 After securing the child restraint system, never slide
the seat.
DRIVING POSITION MEMORY SYSTEM
A microcomputer will memorize the position of the driver’s
seat, the height of the head restraint of the driver’s seat, the
seat cushion length of the driver’s seat, the height of the
shoulder belt anchor of the driver’s seat belt, and the positions
of the tilt and telescopic steering, and outside rear view mirrors.
Three dif ferent driving position profiles can be entered into the
computer’s memory.
Recording a driving position in the computer’s memory can
only be done when the ignition switch is in the “ON” position
and the selector lever is in the “N” or “P” position.
Setting the driving position
16L299
1. Adjust the driver’s seat, driver’s head restraint height
and seat cushion length, driver’s shoulder belt anchor, tilt
and telescopic steering and outside rear view mirrors to
the desired position.

OCCUPANT RESTRAINT SYSTEMS
222Conditions for memorized position activation

Ignition switch “ON” and selector lever in “N” or “P” position
with the vehicle stopped.
All parts of the memorized positions can be activated.
 Ignition switch off and within 30 seconds of opening driver’s
door.
The memorized position can be activated, except for the tilt
and telescopic steering.
If any driving position memory switch is pushed while one of
the memorized driving position profiles is being activated, the
operation will stop.
To activate the system, push the desired button (“1”, “2” or \
“3”)
again.
The driving position memory control system cannot be
operated while the vehicle is moving.
CAUTION
 Do not start the vehicle while the adjustments are
being made.
 Take care not to select the wrong button, or the seat
could strike the rear passenger or hit your body
against the steering wheel. If this happens, you can
stop the movement by pressing another driving
position memory switch.
MEMORY CALL SYSTEM USING A SMART KEY
This system allows you to adjust the driver’s seat, the
driver’s head restraint height, driver’s seat cushion
length, the height of the shoulder belt anchor of the
driver’s seat belt and outside rear view mirrors to the
memorized position when you open the driver’s door after
unlocking it with a smart key. And when you push the
ignition switch, the tilt and telescopic steering is adjusted.
To activate this system, the ID of the smart key needs to
be registered in the memory button.
Registering the smart key ID code
Before the registration of the ID of the smart key, the driving
position must be memorized in the memory button.
When registering, the driver’s door must be closed with the
ignition switch in the “OFF” position.
1. Keep the smart key in possession, select a button in
which you want to record the ID of the key from buttons
“1”, “2” and “3” and push it.
2. Push the “LOCK” or “UNLOCK” button on the smart
key for about one second with button “1”, “2” or “3” held\
down.
When the registration is completed, one beep sounds. If the
key has already been registered, the previous memory will be
erased. If the same driving position profile for the same key is
registered in another button, that memory will also be erased.