2005 KIA Rio oil

Engine Compartment
7-13
Engine coolant reservoir Radiator cap Engine oil fill capAir cleanerAuto transaxle fluid
dipstick (if equipped)Brake/clutch
fluid reservoir
Engine oil dipstick Windshield
washer
fluid
reservoir Power steering
fluid reservoir
(if equipped)Fuse box
Battery
2FDA604
RIO ENG CNA 7-1.qxd 7/29/05 5:16 PM Page 13

Engine Oil and Oil FilterChecking the Engine Oil Level1. Be sure the vehicle is on level ground.
2. Start the engine and allow it to reach normal
operating temperature.
3. Turn the engine off and wait a few minutes for the
oil to return to the oil pan.
4. Pull out the dipstick, wipe it clean, and re-insert it
fully.
5. Pull the dipstick out again and check the level. The
level should be between F and L.
If it is near or at L, add enough oil to bring the level to
F. Do not overfill.Maintenance7-14
Use only the specified engine oil. (Refer to
“Recommended Lubricants’’ later in this section.)
2FDA605
RIO ENG CNA 7-1.qxd 7/29/05 5:16 PM Page 14

Changing the Engine Oil and FilterChange engine oil and filter according to the
Scheduled Maintenance earlier in this section.
1. Warm the engine up for a few minutes and then
turn it off. Remove the oil filler cap.
2. Drain the oil into a suitable container after
removing the oil filler cap and drain plug.
3. Remove the engine oil filter with an oil filter
wrench.4. Use a clean rag to clean the oil filter mounting
surface on the engine.
5. Apply a small amount of engine oil to the new oil
filter O-ring seal.
6. Install the oil filter and tighten it. (Refer to
the oil filter caution label for tightening
instructions.)
7. Replace the drain plug tightly after the oil has
thoroughly drained.
8. Refill the engine with new oil to the F mark on the
dipstick. Do not overfill.
7-15
WARNING - Engine Oil
 Continuous contact with USED engine oil
has caused skin cancer in laboratory mice.
Protect your skin by washing with soap and
water.
 Keep all engine oil out of the reach of
children.
CAUTION
Both the oil and engine are hot. Do not burn
yourself.
✻ ✻
NOTICE
When installing the replacement oil filter, do not
allow the oil filter gasket to remain on the oil
filter mounting surface. This will cause oil
leakage and engine damage. Remove the old
gasket completely so that a new gasket will
properly seat and seal.
RIO ENG CNA 7-1.qxd 7/29/05 5:16 PM Page 15

9. Re-install the oil filler cap securely.
10. Start the engine and inspect around the oil filter
seal for leaks. Stop the engine.
Check the oil level and fill to the F mark, if
necessary.
Oil Capacity
Without filter change : 3.2 L (3.38 US qt.)
With filter change : 3.4 L (3.59 US qt.)
Use only the specified engine oil. (Refer to
“Recommended Lubricants’’ later in this section.)
Engine Cooling SystemThe cooling system is a high-pressure type with a
reservoir and is filled with year-round antifreeze
coolant at the factory.
Check the antifreeze protection and coolant level
at least once a year, at the beginning of the winter
season, and before traveling to a colder climate.
Maintenance7-16
✻ ✻
NOTICE
 Follow these instructions carefully. An
improper oil filter installation can cause oil
leakage and engine damage.
 Although oil filters may have the same
external appearance, their internal designs
differ significantly. These filters are not
interchangeable. To avoid potential engine
damage, use only the specified filter. Consult
an Authorized Kia Dealer.
RIO ENG CNA 7-1.qxd 7/29/05 5:16 PM Page 16

Body LubricationAll moving points of the body, such as doors, hood
hinges and locks, should be lubricated each time the
engine oil is changed.
Use a non-freezing lubricant on locks during cold
weather.
Make sure the engine hood secondary latch keeps the
hood from opening when the primary latch is released.
Lubricants and FluidsChecking the Washer Fluid LevelCheck the fluid level in the washer fluid reservoir and
add fluid if necessary.
Plain water may be used if washer fluid is not
available. However, use windshield washer solvent
with antifreeze characteristics in cold climates to
prevent freezing.Maintenance7-26
CAUTION
 Do not use radiator coolant or antifreeze in the
washer fluid reservoir.
 Radiator coolant can severely obscure visibility
when sprayed on the windshield and may
cause loss of vehicle control or damage to
paint and body trim.
2FDA702
RIO ENG CNA 7-2.qxd 7/29/05 5:18 PM Page 26

7-33
WARNING - Recharging Battery
When recharging the battery, observe the
following precautions:
 The battery must be removed from the
vehicle and placed in an area with good
ventilation.
 Do not allow cigarettes, sparks, or flame
near the battery.
 Watch the battery during charging, and stop
or reduce the charging rate if the battery
cells begin gasing (boiling) violently or if the
temperature of the electrolyte of any cell
exceeds 49°C (120°F).
 Wear eye protection when checking the
battery during charging.
(Continued)
(Continued)
 Disconnect the battery charger in the
following order.
1. Turn off the battery charger main switch.
2. Unhook the negative clamp from the
negative battery terminal.
3. Unhook the positive clamp from the
positive battery terminal.✻ ✻
NOTICE
 Before performing battery maintenance or
recharging, turn OFF all accessories and stop
the engine.
 When remounted battery, disconnect the
negative (–) battery cable first. When re-
installing the battery, reconnect the negative (–)
battery cable last.
RIO ENG CNA 7-2.qxd 7/29/05 5:18 PM Page 33

Maintenance7-42
1. Remove the headlight bulb cover by turning it
counterclockwise.
2. Disconnect the electrical connector from the bulb
assembly.
3. Unsnap the headlight bulb retaining wire by
depressing the end of it and pulling it upward.
4. Remove the bulb.
5. Install a new bulb by aligning the bulb with the
three(3) slots on the headlight assembly and snap the
headlight bulb retaining wire into position.
6. Connect the headlight bulb electrical connector.
7. Install the headlight bulb cover.
Bulb ReplacementHeadlight Bulb Replacement
WARNING - Halogen Bulbs
 Wear eye protection when changing a bulb.
Allow the bulb to cool before handling it.
 Halogen bulbs contain pressurized gas. If
broken, a halogen bulb will explode and will
produce flying pieces of glass.
 Always handle halogen bulbs carefully to
avoid scratches and abrasion. If the bulbs
are lit, avoid contact with liquids. Never
touch the glass with bare hands. Residual oil
may cause the bulb to overheat and burst
when lit. A bulb should be operated only
when installed in the headlight assembly.
 If a bulb becomes damaged or cracked,
replace it immediately and carefully dispose
it.
1B3106004B
RIO ENG CNA 7-2.qxd 7/29/05 5:18 PM Page 42

7-47
Lubricant SpecificationsRecommended LubricantsTo help achieve proper engine and powertrain
performance and durability, use only lubricants of the
proper quality. The correct lubricants also help
promote engine efficiency which results in improved
fuel economy.Engine oils labeled Energy Conserving Oil are now
available. Along with other additional benefits, they
contribute to fuel economy by reducing the amount of
fuel necessary to overcome engine friction. Often,
these improvements are difficult to measure in
everyday driving, but in a year’s time they can offer
significant cost and energy savings.
These lubricants and fluids are recommended for use in your vehicle.
Lubricant Classification
Engine oil *1
API Service SJ, SL or above, ILSAC GF-3 or above
Manual transaxle oil API Service GL-4 (SAE 75W-85)
Automatic transaxle fluid SK ATF SP-III or DIAMOND ATF SP-III
Power steering fluid PSF-III
Brake/clutch fluid SAEJ1703 or FMVSS116 DOT-3 or DOT-4
*¹ Refer to the recommended SAE viscosity numbers on the next page.
RIO ENG CNA 7-2.qxd 7/29/05 5:18 PM Page 47