2005 INFINITI QX4 battery

AV-22
AUDIO
Revision: October 20052005 QX56
Terminals and Reference Value for BOSE Speaker Amp.EKS00BIC
71 (B) 69 (W)Voice guide
signal (with
NAVI)Output ONPress the
"GUIDE/VOICE"
button.Only route guide and
operation guide are
not heard.
72 (W/B) GroundCD eject
signalInput ONOperate EJECT
button0V→5VCD will not eject from
audio unit.
73 (Y/B) GroundCD load sig-
nalInput ONOperate LOAD
button0V→5VCD will not load into
audio unit. Te r m i n a l
(Wire color)
ItemSignal
input/
outputCondition
Reference value
(Approx.)Example of symptom
+–Ignition
switchOperation
SKIA0171J
Te r m i n a l
(wire color)
ItemSignal
input/
outputCondition
Reference value
(Approx.)Example of
symptom
+–Ignition
switchOperation
1 (Y) Ground Battery Input – – Battery voltageSystem does not
work properly.
9 (SB) 10 (B/Y)Rear door
speaker LH
and rear door
tweeter LHOutput ONReceive audio
signalNo sound from
rear door speaker
LH or rear door
tweeter LH.
11 (O/L) 12 (R/L)Rear door
speaker RH
and rear door
tweeter RHOutput ONReceive audio
signalNo sound from
rear door speaker
RH or rear door
tweeter RH.
13 (L/W) 14 (L/R)Front door
speaker LH
and front
tweeter LHOutput ONReceive audio
signalNo sound from
front door speaker
LH or front tweeter
LH.
15 (W/B) 16 (L/B)Front door
speaker RH
and front
tweeter RHOutput ONReceive audio
signalNo sound from
front door speaker
RH or front tweeter
RH.
17 (B) Ground Ground – ON – – –
SKIA0177E
SKIA0177E
SKIA0177E
SKIA0177E

AUDIO
AV-25
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
Terminals and Reference Value for AV SwitchEKS00BIE
Te r m i n a l N o .
(Wire color)
ItemSignal
input/
outputCondition
Voltag e
(Approx.)Example of
symptom
+–Ignition
switchOperation
1 (Y) GroundBattery
powerInput OFF – Battery voltageSystem does not
work properly.
2 (V) Ground ACC signal Input ACC – Battery voltageSystem does not
work properly.
3 (R/L) GroundIllumination
signalInput OFFLighting switch is
ON (position 1).Battery voltageAV switch illumi-
nation does not
come on when
lighting switch is
ON (position 1). Turn lighting switch
OFF.Approx. 3.0V or less
4 (BR) GroundIllumination
control signalInput ONIllumination control
switch is operated
by lighting switch in
1st position.Changes between 0 and 12V.AV switch illumi-
nation cannot be
controlled.
5 (B) Ground Ground – ON – 0V –
6 (V) GroundCommunica-
tion signal (+)Input/
outputON –System does not
work properly.
7–Shield
ground–– – –
8 (LG) GroundCommunica-
tion signal (-)Input/
outputON –System does not
work properly.
12 (R) GroundRemote con-
trol AInput ONPress MODE
switch 0V
Steering wheel
audio controls
do not function. Press SEEK UP
switch0.75V
Press VOL UP
switch2V
Except for above 5V
13 (G) GroundRemote con-
trol BInput ONPress POWER
switch 0V
Steering wheel
audio controls
do not function. Press SEEK
DOWN switch0.75V
Press VOL DOWN
switch2V
Except for above 5V
14 (L) –Remote con-
trol ground–– – –Steering wheel
audio controls
do not function.
16 (W/B) GroundCD EJECT
signalOutput ONPressed 0V
CD eject does
not function.
Released 5V
SKIA0175E
SKIA0176E

AV-30
AUDIO
Revision: October 20052005 QX56
Power Supply Circuit InspectionEKS00BII
1. CHECK FUSES
Check that the following fuses are not blown.
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of problem before installing new fuse. Refer to PG-4,
"POWER SUPPLY ROUTING CIRCUIT" .
Unit Terminals Signal name Fuse No.
Audio unit6 Battery power 31
10 Ignition switch ACC or ON 4
AV s w i t c h1 Battery power 31
2 Ignition switch ACC or ON 4
BOSE speaker amp. 1 Battery power 31
Subwoofer 6 Battery power 17

AUDIO
AV-31
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
2. POWER SUPPLY CIRCUIT CHECK
1. Disconnect audio unit connector M43, subwoofer connector B72 and BOSE speaker amp. connector
M112.
2. Check voltage between the audio unit and ground.
3. Check voltage between subwoofer and ground.
4. Check voltage between BOSE speaker amp. and ground.
OK or NG
OK >> GO TO 3.
NG >>

Check connector housings for disconnected or loose
terminals.

Repair harness or connector.
3. GROUND CIRCUIT CHECK
Check continuity between subwoofer harness connector B72 termi-
nal 5 (B) and BOSE speaker amp. harness connector M112 terminal
17 (B) and ground.
OK or NG
OK >> Inspection End.
NG >>

Check connector housings for disconnected or loose
terminals.

Repair harness or connector.
UnitTerminal No.
OFF ACC ON (+)
(-)
ConnectorTerminal
(wire color)
Audio unit M436 (Y) GroundBattery
voltageBattery
voltageBattery
voltage
10 (V) Ground 0 VBattery
voltageBattery
voltage
SKIA1992E
UnitTerminal No.
OFF ACC ON (+)
(-)
ConnectorTerminal
(wire color)
Sub-
wooferB72 6 (R) GroundBattery
voltageBattery
voltageBattery
voltage
WKIA1598E
UnitTerminal No.
OFF ACC ON (+)
(-)
ConnectorTerminal
(wire color)
BOSE
speaker
amp.M112 1 (Y) GroundBattery
voltageBattery
voltageBattery
voltage
SKIA4 311 E
Continuity should exist.
WKIA1599E

AV-42
AUDIO
Revision: October 20052005 QX56
2. CENTER SPEAKER SIGNAL CHECK
1. Connect BOSE speaker amp. connector M112 and center speaker connector M110.
2. Turn ignition switch to ACC.
3. Push the “POWER” switch.
4. Check the signal between BOSE speaker amp. harness connec-
tor M112 terminals with CONSULT-II or oscilloscope.
OK or NG
OK >> Replace center speaker. Refer to AV- 4 6 , "Removal and Installation of Center Speaker" .
NG >> Replace BOSE speaker amp. Refer to AV-46, "
Removal and Installation of BOSE Speaker Amp."
.
Sound Is Not Heard From SubwooferEKS00BIP
1. CHECK FUSE
Check that the following fuse is not blown.
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of problem before installing new fuse. Refer to PG-4,
"POWER SUPPLY ROUTING CIRCUIT" .
2. POWER SUPPLY CIRCUIT CHECK
1. Disconnect subwoofer connector.
2. Check voltage between the subwoofer and ground.
OK or NG
OK >> GO TO 3.
NG >>

Check connector housings for disconnected or loose
terminals.

Repair harness or connector.
Te r m i n a l s
Condi-
tionReference
signal (+) (-)
Con-
nec-
torTe r m i n a l
(Wire
color)Con-
nec-
torTerminal
(Wire
color)
M112 18 (V) M112 2 (R)Receive
audio
signal
WKIA1223E
SKIA0177E
Unit Terminal Signal name Fuse No.
Subwoofer 6 Battery power 17
UnitTe r m i n a l N o .
OFF ACC ON (+)
(-)
ConnectorTe r m i n a l
(wire color)
Sub-
wooferB72 6 (R) GroundBattery
voltageBattery
voltageBattery
voltage
WKIA1601E

AUDIO
AV-45
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
Removal and Installation for Audio UnitEKS00BIQ
1. Remove cluster lid C. Refer to IP-12, "Cluster Lid C" .
2. Disconnect the negative battery cable.
3. Using power tool, remove the four audio unit screws.
4. Pull out audio unit and disconnect connectors.
5. Installation is in the reverse order of removal.
Removal and Installation for AV SwitchEKS00BIR
1. Remove cluster lid C. Refer to IP-12, "Cluster Lid C" .
2. Remove the four AV switch screws.
3. Carefully remove the AV switch.
4. Installation is in the reverse order of removal.
Removal and Installation of Front Door SpeakerEKS00BIS
1. Remove door finisher. Refer to EI-32, "DOOR FINISHER" .
2. Remove the four front door speaker screws.
3. Disconnect connector and remove the speaker.
4. Installation is in the reverse order of removal.
Removal and Installation of Rear Door SpeakerEKS00BIT
1. Remove door finisher. Refer to EI-32, "DOOR FINISHER" .
2. Remove the three rear speaker screws and remove speaker.
3. Disconnect connector.
4. Installation is in the reverse order of removal.
WKIA1490E
WKIA1798E
Front door speaker
screws: 3.5 N·m (0.36 kg-m, 31 in-lb)
WKIA1498E
Rear speaker screws : 3.5 N·m (0.36 kg-m, 31 in-lb)
WKIA1492E

AV-58
DVD ENTERTAINMENT SYSTEM
Revision: October 20052005 QX56
Trouble DiagnosisEKS00BJ9
Symptom Possible causes Repair order
DVD player inoperative1. Power supply
2. Ground circuit
3. Audio enable circuit
4. DVD enable signal
5. Audio enable signal
6. DVD player
7. Audio unit1. Refer to AV- 5 9 , "
Power Supply Circuit Inspection" .
2. Refer to AV- 5 9 , "
Power Supply Circuit Inspection" .
3. Check audio enable circuits for open or short between
audio unit terminals 39, 40 and DVD player terminals
11 , 9 .
4. Push power switch of DVD player and verify approx.
5V is present at terminal 39 of audio unit.
5. Push power switch of DVD player and verify approx.
5V is present at terminal 9 of DVD player.
6. Remove DVD player for repair.
7. Remove audio unit for repair.
No sound when playing
DVD1. Audio signal circuits
2. DVD player
3. Audio unit1. Check audio signal circuits for open or short between
DVD player terminals 1, 2, 3 and 4 and audio unit ter-
minals 34, 35, 36 and 37.
2. Remove DVD player for repair.
3. Remove audio unit for repair.
Video monitor is inopera-
tive/does not operate prop-
erly1. Power supply
2. Video monitor ground circuit
3. Video circuits
4. Data signal
5. Video monitor
6. DVD player1. Operate DVD player and verify battery positive voltage
is present at terminals 11 and 12 of video monitor. Ver-
ify approximately 5 volts is present at terminal 10 of
video monitor.
2. Check video monitor ground circuits between DVD
player terminals 19 and 27 and video monitor terminals
1 and 2.
3. Check video circuits between DVD player terminals 23
and 24 and video monitor terminals 7 and 8.
4. Check data signal circuit for open or short between
DVD player terminal 29 and video monitor terminal 5.
5. Remove video monitor for repair.
6. Remove DVD player for repair.
DVD remote control is
inoperative/does not oper-
ate properly1. Data signal
2. DVD player remote control batteries
3. DVD player remote control
4. Video monitor1. Check data signal circuit for open or short between
DVD player terminal 28 and video monitor terminal 6.
2. Replace DVD player remote control batteries.
3. Replace DVD player remote control.
4. Remove video monitor for repair.
Headphones inoperative 1. Headphone batteries
2. Headphones
3. Rear audio remote control unit1. Replace headphone batteries.
2. Replace headphones.
3. Replace rear audio remote control unit.
Snowy video/poor audio 1. Harness or connectors
2. DVD player1. Check harness and connectors for open or short.
2. Check DVD player.
Snowy video (audio OK) 1. Harness or connectors
2. DVD player1. Check harness and connectors for open or short.
2. Check DVD player.
No video (audio OK) 1. Harness or connectors
2. DVD player
3. Video monitor1. Check harness and connectors for open or short.
2. Check DVD player.
3. Check video monitor.
Dim video (audio OK) 1. Harness or connectors
2. DVD player
3. Video monitor1. Check harness and connectors for open or short.
2. Check DVD player.
3. Check video monitor.

DVD ENTERTAINMENT SYSTEM
AV-59
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
Power Supply Circuit InspectionEKS00BJA
1. CHECK FUSES
Check that the following fuses are not blown.
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of problem before installing new fuse. Refer to PG-4,
"POWER SUPPLY ROUTING CIRCUIT" .
2. POWER SUPPLY CIRCUIT CHECK
1. Disconnect DVD player connector M205.
2. Check voltage between the DVD player and ground.
OK or NG
OK >> GO TO 3.
NG >>

Check connector housings for disconnected or loose terminals.

Repair harness or connector.
3. GROUND CIRCUIT CHECK
Check continuity between DVD player harness connector M206 ter-
minal 22 (B) and ground.
OK or NG
OK >> Inspection End.
NG >>

Check connector housings for disconnected or loose
terminals.

Repair harness or connector.
Unit Terminals Signal name Fuse No.
DVD player16 Battery power 31
15 Ignition switch ACC or ON 4
UnitTe r m i n a l N o .
OFF ACC ON (+)
(-)
ConnectorTe r m i n a l
(wire color)
DVD player M20516 (Y) GroundBattery
voltageBattery
voltageBattery
voltage
15 (V) Ground 0 VBattery
voltageBattery
voltage
WKIA1197E
Continuity should exist.
WKIA1198E