2005 INFINITI QX4 battery

AT-232
ON-VEHICLE SERVICE
Revision: October 20052005 QX56
CONTROL VALVE WITH TCM REMOVAL AND INSTALLATION
Removal
1. Disconnect negative battery terminal
2. Drain ATF through drain plug.
3. Disconnect A/T assembly harness connector.
4. Remove snap ring from A/T assembly harness connector.
5. Push A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
6. Remove oil pan and oil pan gasket, refer to AT-229, "
Removal" .
7. Disconnect A/T fluid temperature sensor 2 connector.
CAUTION:
Be careful not to damage connector.
8. Straighten terminal clip to free terminal cord assembly A/T fluid
temperature sensor 2 harness.
SCIA5021E
SCIA5022E
SCIA5023E
SCIA5446E

AT-238
ON-VEHICLE SERVICE
Revision: October 20052005 QX56
13. Connect revolution sensor connector.
14. Securely fasten revolution sensor harness with terminal clips.
15. Install oil pan to transmission case, refer to AT-229, "
Installation" .
16. Pull up A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
17. Install snap ring to A/T assembly harness connector.
18. Connect A/T assembly harness connector.
19. Pour ATF into transmission assembly. Refer to MA-24, "
Chang-
ing A/T Fluid" .
20. Connect the negative battery terminal
SCIA5024E
SCIA3969E
SCIA5038E
SCIA5039E

ON-VEHICLE SERVICE
AT-239
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
A/T FLUID TEMPERATURE SENSOR 2 REMOVAL AND INSTALLATION
Removal
1. Disconnect negative battery terminal
2. Remove oil pan and oil pan gasket, refer to AT - 2 2 9 , "
Removal" .
3. Disconnect A/T fluid temperature sensor 2 connector.
CAUTION:
Be careful not to damage connector.
4. Straighten terminal clip to free A/T fluid temperature sensor 2
harness.
5. Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
6. Remove bracket from A/T fluid temperature sensor 2.
SCIA5023E
SCIA5146E
SCIA5253E
SCIA5264E

AT-240
ON-VEHICLE SERVICE
Revision: October 20052005 QX56
Installation
CAUTION:
After completing installation, check for A/T fluid leakage and fluid level. Refer to MA-24, "
Changing A/
T Fluid" , MA-22, "Checking A/T Fluid" .
1. Install A/T fluid temperature sensor 2 to bracket.
2. Install A/T fluid temperature sensor 2 (with bracket) in control
valve with TCM. Tighten A/T fluid temperature sensor 2 mount-
ing bolt to the specified torque. Refer to AT- 2 5 0 , "
Components" .
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
3. Connect A/T fluid temperature sensor 2 connector.
4. Securely fasten A/T temperature sensor 2 harness with terminal
clip.
5. Install oil pan to transmission case, refer to AT-229, "
Installation" .
6. Connect the negative battery terminal
SCIA5264E
SCIA5253E
SCIA5023E
SCIA5146E

AT-244
TRANSMISSION ASSEMBLY
Revision: October 20052005 QX56
TRANSMISSION ASSEMBLYPFP:31020
Removal and Installation (4x2)ECS00CL0
COMPONENTS
REMOVAL
CAUTION:
When removing the A/T assembly from engine, first remove the crankshaft position sensor (POS) from
the A/T assembly.
Be careful not to damage sensor edge.
1. Disconnect the negative battery terminal.
2. Remove engine cover.
3. Remove A/T fluid indicator gauge.
4. Remove engine under cover with power tool.
5. Remove exhaust front tube and center muffler with power tool. Refer to EX-4, "
REMOVAL" .
6. Remove rear propeller shaft. Refer to PR-9, "
REMOVAL" .
7. Remove A/T control cable. Refer to AT-228, "
REMOVAL" .
1. A/T fluid indicator pipe 2. A/T fluid indicator 3. O-ring
4. Transmission assembly 5. Fluid cooler tube 6. A/T cross member
7. Insulator 8. Copper washers
LCIA0354E

TRANSMISSION ASSEMBLY
AT-247
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
Removal and Installation (4x4) ECS0 0CL 1
COMPONENTS
REMOVAL
CAUTION:
When removing the A/T assembly from engine, first remove the crankshaft position sensor (POS) from
the A/T assembly.
Be careful not to damage sensor edge.
1. Disconnect the negative battery terminal.
2. Remove engine cover with power tool.
3. Remove A/T fluid indicator.
4. Remove engine under cover with power tool.
5. Remove exhaust front tube and center muffler with power tool. Refer to EX-4, "
REMOVAL" .
6. Remove propeller shaft. Refer to PR-5, "
REMOVAL" , and PR-9, "REMOVAL" .
7. Remove A/T control cable. Refer to AT- 2 2 8 , "
REMOVAL" .
1. A/T fluid indicator pipe 2. A/T fluid indicator 3. O-ring
4. Transmission assembly 5. Fluid cooler tube 6. Copper washer
7. A/T cross member 8. Insulator
WCIA0428E

PREPARATION
ATC-15
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: October 20052005 QX56
—
(J-41995)
Electronic refrigerant leak detectorPower supply:

DC 12V (battery terminal)
—
(J-43926)
Refrigerant dye leak detection kit
Kit includes:
(J-42220) UV lamp and UV safety
goggles
(J-41459) Refrigerant dye injector
(J-41447) qty. 24
HFC-134a (R-134a) refrigerant
dye
(J-43872) Refrigerant dye cleanerPower supply:

DC 12V (battery terminal)
—
(J-42220)
Fluorescent dye leak detectorPower supply:

DC 12V (battery terminal)
For checking refrigerant leak when flu-
orescent dye is installed in A/C system.
Includes: UV lamp and UV safety gog-
gles
—
(J-41447)
HFC-134a (R-134a) Fluorescent
leak detection dye
(Box of 24, 1/4 ounce bottles)Application: For HFC-134a (R-134a)
PAG oil
Container: 1/4 ounce (7.4cc) bottle
(Includes self-adhesive dye identifica-
tion labels for affixing to vehicle after
charging system with dye.)
—
(J-41459)
HFC-134a (R-134a) Dye injector
Use with J-41447, 1/4 ounce bottleFor injecting 1/4 ounce of fluorescent
leak detection dye into A/C system.
—
(J-43872)
Refrigerant dye cleanerFor cleaning dye spills. Tool number
(Kent-Moore No.)
Tool nameDescription
AHA2 81 A
ZHA2 00 H
SHA438F
SHA439F
SHA440F
SHA441F

ATC-34
TROUBLE DIAGNOSIS
Revision: October 20052005 QX56
SELF-DIAGNOSIS
Operation Procedure
1. Touch “SELF-DIAG RESULTS” on “SELECT DIAG MODE”
screen to view all set DTC's.
Display Item List
DATA MONITOR
Operation Procedure
1. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
2. Touch either “MAIN SIGNALS” or “SELECTION FROM MENU” on “DATA MONITOR” screen.
3. When “SELECTION FROM MENU” is selected, touch items to be monitored. When “MAIN SIGNALS” is
selected, all the items will be monitored.
4. Touch “START”.
5. Touch “RECORD” while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch “STOP”.
BCIA0031E
DTC Description
Reference page
B2573 Battery voltage out of rangeSC-4, "
BATTERY"
B2578 In-vehicle sensor circuit out of range (low)
ATC-140, "In-vehicle Sensor Circuit"B2579 In-vehicle sensor circuit out of range (high)
B257B Ambient sensor circuit short
ATC-137, "
Ambient Sensor Circuit"B257C Ambient sensor circuit open
B257F Optical sensor (Driver) circuit open or short
ATC-143, "
Optical Sensor Circuit"B2580 Optical sensor (Passenger) circuit open or short
B2581 Intake sensor circuit short
ATC-145, "
Intake Sensor Circuit"B2582 Intake sensor circuit open
U1000 CAN bus faultLAN-5, "
CAN COMMUNICATION"
B2587 Stuck buttonATC-147, "FRONT AIR CONTROL"
BCIA0031E
MAIN SIGNALS Monitors all the items.
SELECTION FROM
MENUSelects and monitors the individual item selected.