GI-38
CONSULT-II CHECKING SYSTEM
Revision: October 20052005 QX56
Nickel Metal Hydride Battery Replacement EAS001XT
CONSULT-II contains a nickel metal hydride battery. When replacing the battery obey the following:
WAR NIN G:
Replace the nickel metal hydride battery with Genuine CONSULT-II battery only. Use of another bat-
tery may present a risk of fire or explosion. The battery may present a fire or chemical burn hazard if
mistreated. Do not recharge, disassemble or dispose of in fire.
Keep the battery out of reach of children and discard used battery conforming to the local regulations.
Checking EquipmentEAS001XU
When ordering the below equipment, contact your NISSAN distributor.
CAUTION:
Previous CONSULT-II “I” and “Y” DLC-I and DLC-II cables should NOT be used anymore because
their DDL connector pins can be damaged during cable swapping.
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self- diagnosis depending on control unit which carries out CAN communication.
If CONSULT-II CONVERTER is not connected with CONSULT-II, the vehicle enters “FAIL SAFE
MODE” which will “LIGHT UP the HEAD LIGHT” and /or “COOLING FAN ROTATING” when CON-
SULT-II is started.
NOTE:
The CONSULT-II must be used in conjunction with a program card.
CONSULT-II does not require loading (Initialization) procedure.
Be sure the CONSULT-II is turned OFF before installing or removing a program card.
CONSULT-II Start ProcedureEAS001XV
NOTE:
Turning ignition switch off when performing CAN diagnosis could cause CAN memory to be erased.
1. Connect CONSULT-II and CONSULT-II CONVERTER to the
data link connector.
Tool name Description
NISSAN CONSULT-II (J-44200)
1. CONSULT-II unit (Tester internal soft: Resident
Version 3.4.0) and accessories.
2. Program card UED05B-1 and AEN04A-1 (for
NATS) or later, to confirm the best combination
of these software, refer to CONSULT-II Opera-
tion Manual.
3. CONSULT-II CONVERTER.
4. "CONSULT-II pigtail" cable.
SAIA0363E
PAIA0070E
TOW TRUCK TOWING
GI-43
C
D
E
F
G
H
I
J
K
L
MB
GI
Revision: October 20052005 QX56
4WD MODELS
NISSAN does not recommend towing automatic transmission
equipped vehicles with the drive wheels on the ground.
CAUTION:
When towing with the front wheels on the ground or rear
wheels on the ground (If you do not use towing dollies): Set
the free-running hubs to the free position and move the
transfer case shift lever into the “2H” position.
When towing with the front on the ground: Turn the ignition
key to the OFF position and secure the steering wheel in a
straight ahead position with a rope or similar device. Never
place the ignition key in the LOCK position. This will result
in damage to the steering lock mechanism.
Towing Point
CAUTION:
Never tow the vehicle using only the towing points. To avoid
damaging the vehicle body, use proper towing equipment when
towing.
Vehicle Recovery (Freeing a stuck vehicle)EAS001FZ
Tow chains or cables must be attached only to the main structural members of the vehicle or the
towing hooks (if so equipped). Otherwise, the vehicle body will be damaged.
Use the towing hook (if so equipped) only to free a vehicle stuck in sand, snow, mud, etc. Never
tow the vehicle for a long distance using only the towing hook.
The towing hook is under tremendous force when used to free a stuck vehicle. Never pull the hook
at an angle.
Always pull the cable straight out from the front or rear of the vehicle.
Pulling devices should be routed so they do not touch any part of the suspension, steering, brake,
or cooling systems.
Pulling devices such as ropes or canvas straps are not recommended for use in vehicle towing or
recovery.
WA RN ING:
Stand clear of a stuck vehicle.
Do not spin your tires at high speed. This could cause them to explode and result in serious injury.
Parts of your vehicle could also overheat and be damaged.
WAIA0032E
WAIA0055E
IDX-3
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
Body repair ....................................................... BL-160
Body sealing ..................................................... BL-168
Brake booster .................................................... BR-16
Brake fluid level ................................................. MA-28
Brake hydraulic line ........................................... BR-11
Brake inspection ................................................ MA-28
Brake lines and cables inspection ..................... MA-28
Brake master cylinder ....................................... BR-14
Brake switch ...................................... EC-569, EC-586
BRK/SW - Wiring diagram ............................... EC-587
Bulb specifications ........................................... LT-170
Bumper, front ...................................................... EI-13
Bumper, rear ....................................................... EI-15
C
Camshaft ........................................................... EM-43
Camshaft inspection .......................................... EM-46
Camshaft position sensor (PHASE) ................ EC-291
CAN - Wiring diagram EC-164, LAN-18, LAN-52, LAN-
92, LAN-128
CAN (Controller Area Network) BRC-10, SE-17, LAN-
16, LAN-50, LAN-90, LAN-126
CAN communication ... EC-31, EC-163, AT-95, TF-20,
TF-113
, BRC-10, SE-17, LAN-16, LAN-50, LAN-90,
LAN-126
Canister-See EVAP canister ............................. EC-35
Center case (Transfer) ....................... TF-152, TF-165
CHARGE - Wiring diagram ............................... SC-18
Charging system ............................................... SC-17
Chassis and body maintenance ........................ MA-21
Chassis and body maintenanceSchedule 1 ........ MA-8
Chassis and body maintenanceSchedule 2 ...... MA-10
CHIME - Wiring diagram ..................................... DI-44
Circuit breaker ................................................... PG-66
Clock ................................................................... DI-69
CLOCK - Wiring diagram .................................... DI-69
Closed loop control ........................................... EC-25
Closed loop control (Bank 1) ........................... EC-437
Closed loop control (Bank 2) ........................... EC-437
Clutch drum (Transfer) ....................... TF-152, TF-165
Clutch pressure switch (Transfer) ...... TF-152, TF-165
Coil spring (front) ............................................. FSU-10
Collision diagnosis .......................................... SRS-61
Combination lamp, front, removal and installation . LT-
32
Combination lamp, rear, removal and installation .. LT-
122
Combination meter ................................................ DI-5
Combination switch ............................................ LT-97
COMBSW - Wiring diagram ............................... LT-97
COMM - Wiring diagram ................................... AV-87
COMPAS - Wiring diagram ................................. DI-27
Compass ............................................................. DI-26
Component Location (auto A/C) ...................... ATC-39
Compressor clutch removal and installation . ATC-180
Compressor mounting ................................... ATC-179
Compressor precaution ................................... ATC-11
Compressor special service tool ..................... ATC-14
Condenser ..................................................... ATC-185
Connecting rod .................................................. EM-91
Connecting rod bearing clearance ..................... EM-91
Connecting rod bushing clearance .................... EM-91
Console box - See Instrument panel ................... IP-10
CONSULT for VDC ......................................... BRC-28
CONSULT general information ........................... GI-37
CONSULT-II for engine ................................... EC-126
Control units (terminal arrangement) ................. PG-71
Control valve (A/T) ............................................. AT-35
Control valve (Transfer) ...................... TF-152, TF-165
Controller Area Network (CAN) BRC-10, SE-17, LAN-
16, LAN-50, LAN-90, LAN-126
Converter housing installation ............ AT-246, AT-249
COOL/F - Wiring diagram ................................ EC-443
Coolant mixture ratio ......................................... MA-12
Coolant replacement ......................................... MA-13
Cooling circuit (engine) ........................................ CO-8
Cooling fan ........................................................ CO-15
Cooling fan control ........................................... EC-440
Cooling fan motor ............................................ EC-449
Cooling unit (A/C evaporator) ....... ATC-156, ATC-186
Corrosion protection ......................................... BL-165
Crankcase ventilation system - See Positive crankcase
ventilation .......................................................... EC-45
Crankshaft ......................................................... EM-74
Crankshaft position sensor (POS) ................... EC-284
Crash zone sensor .......................................... SRS-56
CVT shift lock system - Wiring diagram ........... AT-223
Cylinder block .................................................... EM-73
Cylinder block boring ......................................... EM-94
D
D/LOCK - Wiring diagram ................................... BL-19
Data link connector for Consult ......... EC-128, EC-140
Daytime light system .......................................... LT-33
Daytime running light - See Daytime light system .. LT-
33
Diagnosis sensor unit ...................................... SRS-59
Diagnostic trouble code (DTC) for OBD system . EC-8,
EC-53
Diagnostic trouble code (DTC) inspection priority chart
EC-101
Differential carrier assembly ............................ RFD-12
Differential carrier disassembly ....................... RFD-14
Differential gear oil replacement ........................ MA-25
Dimensions ......................................................... GI-49
Direct clutch solenoid valve ................ AT-148, AT-150
Display and amp.assembly .............................. ATC-61
Display Control Unit ......................................... AV-158
Dome light - See Interior lamp .......................... LT-129
Door glass .......................................... GW-68, GW-71
Door lock .......................................................... BL-131
Door mirror lamp ............................................... LT-129
Door trim .............................................................. EI-32
Door, front ........................................... BL-128, GW-68
Door, rear ........................................... BL-128, GW-71
Drive belt ........................................................... EM-12
IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
GPS antenna ..................................................... AV-62
Grease .............................................................. MA-11
Ground distribution ............................................ PG-29
H
H/AIM - Wiring diagram ...................................... LT-66
Handling precautions for plastics ..................... BL-187
Harness connector ............................................ PG-67
Harness layout .................................................. PG-39
Hazard warning lamp ......................................... LT-80
Headlamp aiming control ................................... LT-66
Headlamp leveler - See Headlamp aiming control . LT-
66
Headlamp removal and installation .................... LT-32
Heated oxygen sensor 2 (bank 1) .... EC-216, EC-225,
EC-415
, EC-426
Heated oxygen sensor 2 (bank 2) .... EC-216, EC-225,
EC-415
, EC-426
Heated oxygen sensor 2 heater (bank 1) ........ EC-166
Heated oxygen sensor 2 heater (bank 2) ........ EC-166
Heated seat ....................................................... SE-90
Heater and cooling unit (Heater core) . ATC-156, ATC-
160
Heater unit (heater core) ............... ATC-156, ATC-160
Height (Dimensions) ........................................... GI-49
HFC134a (R134a) system identification ........... ATC-7
HFC134a (R134a) system precaution ............... ATC-5
HFC134a (R134a) system service procedure ATC-175
HFC134a (R134a) system service tools ......... ATC-14
HFC134a system service equipment precaution ATC-
11
High & low reverse clutch solenoid valve . AT-152, AT-
154
Homelink universal transceiver ........................ BL-156
Horn ................................................................ WW-58
HORN - Wiring diagram .................................. WW-58
How to erase DTC for OBD system .................. EC-62
HSEAT - Wiring diagram ................................... SE-92
I
I/MIRR - Wiring diagram ................................... GW-75
IATS - Wiring diagram ..................................... EC-192
ICC - Wiring diagram ....................................... ACS-20
ICC/BS - Wiring diagram ................................. EC-562
ICC/SW - Wiring diagram ................................ EC-547
ICCBOF - Wiring diagram ............................... EC-650
Identification plate .............................................. GI-47
Idle air volume learning ..................................... EC-91
Idle mixture ratio ................................................ EC-79
Idle speed .............................................. EC-72, EC-77
Idle speed control (ISC) .................... EC-374, EC-376
Ignition coil .......................................... EM-26, EC-619
Ignition control system .................................... EC-619
Ignition key hole illumination ............................ LT-129
Ignition timing ........................................ EC-72, EC-77
IGNSYS - Wiring diagram ............................... EC-620
ILL - Wiring diagram ......................................... LT-158
Illumination ....................................................... LT-152
In vehicle sensor ........................... ATC-140, ATC-149
INJECT - Wiring diagram ................................. EC-632
Injector ............................................................. EC-631
Input clutch solenoid valve ................. AT-140, AT-142
Instrument panel .................................................. IP-10
Instrument panel speaker .................................. AV-46
Intake air temperature sensor ............ EC-191, EC-211
Intake door control linkage adjustment . ATC-85, ATC-
88
Intake door motor ........................... ATC-83, ATC-164
Intake manifold .................................................. EM-15
Intake sensor ................................ ATC-145, ATC-151
Integrated homelink transmitter - See Homelink univer-
sal tranceiver .................................................... BL-156
Intelligent cruise control (ICC) system ............... ACS-6
Interior ................................................................. EI-35
Interior lamp ...................................................... LT-129
Interior lamp on-off control ................................ LT-130
Internal gear (Transfer) ....................... TF-147, TF-174
IPDM (Intelligent power distribution module engine
room) ................................................................. PG-17
IVIS (Infiniti vehicle immobilizer system) .......... BL-137
IVIS (Infiniti vehicle immobilizer system) precautions ...
GI-3
J
Jacking points ..................................................... GI-40
Junction box (J/B) .............................................. PG-76
K
Key illumination ................................................ LT-130
KEYLES - Wiring diagram .................................. BL-49
Knock sensor (KS) ........................................... EC-279
KS - Wiring diagram ........................................ EC-280
L
Length (Dimensions) .......................................... GI-49
License lamp .................................................... LT-108
Lifting points ....................................................... GI-41
Line pressure solenoid valve ........................... AT-119
Line pressure switch (Transfer) .......... TF-152, TF-165
Line pressure test (A/T) ..................................... AT-51
Location of electrical units ................................. PG-63
Low coast brake solenoid valve .......... AT-156, AT-158
Low tire pressure warning system ...................... WT-8
Low tire pressure warning system - trouble diagnoses
WT-11
Low tire pressure warning system - Wiring diagram .....
WT-11
Lubricant (R134a) A/C ..................................... ATC-22
Lubricants .......................................................... MA-11
Lubrication circuit (engine) .................................. LU-5
Lubrication oil A/C ........................................... ATC-22
Lubrication-locks, hinges and hood latches ....... MA-31
LAN-6
[CAN]
CAN COMMUNICATION
Revision: October 20052005 QX56
Input/output signal chart
T: Transmit R: Receive
Signals ECM TCMDriver
seat
con-
trol
unitCom-
bina-
tion
meterDis-
play
con-
trol
unitBCMStee r-
ing
angle
sensorFront
air
control ABS
actua-
tor and
elec-
tric unit
(con-
trol
unit)IPDM
E/R
Engine speed signal T R R R R
Engine status signal T R R
Engine coolant temperature signal T R R R
A/T self-diagnosis signal R T
Accelerator pedal position signal T R R
Closed throttle position signal T R
Wide open throttle position signal T R
Battery voltage signal T R
Key switch signal R T
Ignition switch signal R T R
P range signal T R
Stop lamp switch signal R T
Parking brake switch signal T R
Fuel consumption monitor signalTR
TR
Turbine revolution signal R T
Output shaft revolution signal R T
A/C switch signal R T
A/C compressor request signal T R R
Blower fan motor switch signal R T R
A/C switch/indicator signalTR
RT
Cooling fan speed request signal T R R
Position light request signal R T R
Low beam request signal T R
Low beam status signal RT
High beam request signal R T R
High beam status signal RT
Front fog light request signal T R
Day time running light request signal T R
Vehicle speed signalRRT
RRRTRR R
Sleep wake up signal R T R
Door switch signal R R R T R
Turn indicator signal R T
Key fob ID signal R T
Key fob door unlock signal R T
Buzzer output signal R T
CAN COMMUNICATION
LAN-9
[CAN]
C
D
E
F
G
H
I
J
L
MA
B
LAN
Revision: October 20052005 QX56
A/C switch/indicator signalTR
RT
Cooling fan speed request signal T R R
Position light request signal R T R
Low beam request signalTR
Low beam status signal RT
High beam request signal R T R
High beam status signal RT
Front fog light request signal T R
Day time running light request signal T R
Vehicle speed signalRRT
RR R R T R R R
Sleep wake up signal R T R
Door switch signal R R R T R
Turn indicator signal R T
Key fob ID signal R T
Key fob door unlock signal R T
Buzzer output signalRT
TR
Fuel level sensor signal R T
Fuel level low warning signal T R
Malfunction indicator lamp signal T R
Front wiper request signal R T R
Front wiper stop position signal R T
Rear window defogger switch signal T R R
Rear window defogger control signal R R T
Hood switch signalRT
Theft warning horn request signal T R
Horn chirp signalTR
Steering angle sensor signalTR
ABS warning lamp signal R T
VDC OFF indicator lamp signal R R T
SLIP indicator lamp signal R T
Brake warning lamp signal R T
VDC operation signal R T
ABS malfunction signal R T
TCS malfunction signal R T
VDC malfunction signal R TSignals ECM TCMICC
sen-
sorICC
unitDriver
seat
con-
trol
unitCom-
bina-
tion
mete
rDis-
play
con-
trol
unitBCMSteer-
ing
angle
sensorFront
air
con-
trol ABS
actu-
ator
and
elec-
tric
unit
(con-
trol
unit)IPD
M E/
R
CAN COMMUNICATION
LAN-11
[CAN]
C
D
E
F
G
H
I
J
L
MA
B
LAN
Revision: October 20052005 QX56
Input/output signal chart
T: Transmit R: Receive
Signals ECM TCMDriver
seat
con-
trol
unitCom-
bina-
tion
meterDis-
play
con-
trol
unitBCMStee r-
ing
angle
sen-
sorFront
air
con-
trolTran s-
fer
con-
trol
unitABS
actua-
tor
and
elec-
tric
unit
(con-
trol
unit)IPDM
E/R
A/T self-diagnosis signal R T
Stop lamp switch signal R T
Parking brake switch signal T R
Battery voltage signal T R
Key switch signal R T
Ignition switch signal R T R
P range signal T R
Closed throttle position signal T R
Wide open throttle position signal T R
Engine speed signal T R R R R R
Engine status signal T R R
Engine coolant temperature signal T R R R
Accelerator pedal position signal T R R R
Fuel consumption monitor signalTR
TR
Turbine revolution signal R T
Output shaft revolution signal R T R
A/C switch signal R T
A/C compressor request signal T R R
Blower fan motor switch signal R T R
A/C switch/indicator signalTR
RT
Cooling fan speed request signal T R R
Position light request signal R T R
Low beam request signal T R
Low beam status signal RT
High beam request signal R T R
High beam status signal RT
Front fog light request signal T R
Day time running light request signal T R
Vehicle speed signalRRRT
RRRT RR R
Sleep wake up signal R T R
Door switch signal R R R T R
Turn indicator signal R T
Key fob ID signal R T
Key fob door unlock signal R T
LAN-14
[CAN]
CAN COMMUNICATION
Revision: October 20052005 QX56
A/C switch/indicator signalTR
RT
Cooling fan speed request signal T R R
Position light request signal R T R
Low beam request signal T R
Low beam status signal RT
High beam request signal R T R
High beam status signal RT
Front fog light request signal T R
Day time running light request
signalTR
Vehicle speed signalR RRT
RRR R T R R R
Sleep wake up signal R T R
Door switch signal R R R T R
Turn indicator signal R T
Key fob ID signal R T
Key fob door unlock signal R T
Buzzer output signalRT
TR
Fuel level sensor signal R T
Malfunction indicator lamp signal T R
Fuel level low warning signal T R
Front wiper request signal R T R
Front wiper stop position signal R T
Rear window defogger switch sig-
nalTR R
Rear window defogger control
signalRRRT
Hood switch signalRT
Theft warning horn request signal T R
Horn chirp signalTR
Steering angle sensor signal T R
ABS warning lamp signal R T
VDC OFF indicator lamp signal R R T
SLIP indicator lamp signal R T
Brake warning lamp signal R T
VDC operation signal R T
ABS malfunction signal R TSignals ECM TCMICC
sen-
sorICC
unitDriver
seat
con-
trol
unitCom-
bina-
tion
mete
rDis-
play
con-
trol
unitBCMStee r-
ing
angle
sen-
sorFront
air
con-
trolTran s -
fer
con-
trol
unitABS
actu-
ator
and
elec-
tric
unit
(con-
trol
unit)IPD
M
E/R