2005 INFINITI FX35 weight

CHASSIS AND BODY MAINTENANCE MA-33
C
D E
F
G H
I
J
K
M A
B
MA
Revision: 2005 July 2005 FX
Changing Differential Gear OilALS000FN
1. Drain oil from drain plug and refill with new gear oil.
2. Check oil level.
Balancing Wheels (Bonding Weight Type)ALS000FO
REMOVAL
1. Remove inner and outer balance weights from the road wheel. CAUTION:
Be careful not to scratch the road wheel during removal.
2. Using releasing agent, remove double-faced adhesive tape from the road wheel. CAUTION:

Be careful not to scratch the road wheel during removal.

After removing double-faced adhesive tape, wipe clean traces of releasing agent from the road
wheel.
WHEEL BALANCE ADJUSTMENT

If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting,
select and adjust a drive-in weight mode suitable for road wheels.
1. Set road wheel on wheel balancer using the center hole as a guide. Start the tire balance machine.
2. When inner and outer unbalance values are shown on the wheel balancer indicator, multiply outer unbal- ance value by 5/3 to determine balance weight that should be used. Select the outer balance weight with
a value closest to the calculated value above and install it to the designated outer position of, or at the
designated angle in relation to the road wheel.
CAUTION:

Do not install the inner balance weight before installing the outer balance weight. Oil grade and Viscosity:
Refer to MA-12, "
RECOMMENDED FLUIDS
AND LUBRICANTS" .
Capacity:
Front final drive (F160A)
0.65 (1 - 3/8 US pt, 1 - 1/8 lmp pt)
Rear final drive (R200)
1.4 (3 US pt, 2 - 1/2 lmp pt)
Filler plug: Front final drive
: 34.5 N-m (3.5 kg-m, 25 ft-lb)
Rear final drive
: 34.5 N-m (3.5 kg-m, 25 ft-lb)
Drain plug: Front final drive
: 34.5 N-m (3.5 kg-m, 25 ft-lb)
Rear final drive
: 34.5 N-m (3.5 kg-m, 25 ft-lb)
SDIA1151E

MA-34
CHASSIS AND BODY MAINTENANCE
Revision: 2005 July 2005 FX

Before installing the balance weight, be sure to clean the
mating surface of the road wheel.
Indicated unbalance value × 5/3 = balance weight to be installed
Calculation example:
23 g (0.81 oz) × 5/3 = 38.33 g (1.35 oz) = 40 g (1.41 oz) balance
weight (closer to calculated balance weight value)
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
37.4 = 35 g (1.23 oz)
37.5 = 40 g (1.41 oz)
a. Install balance weight in the position shown in the figure at right.
b. When installing balance weight to road wheels, set it into the grooved area on the inner wall of the road wheel as shown in the
figure so that the balance weight center is aligned with the wheel
balancer indication position (angle).
CAUTION:

Always use genuine Nissan adhesion balance weights.

Balance weights are unreusable; always replace with new
ones.

Do not install more than three sheets of balance weight.
c. If calculated balance weight value exceeds 50 g (1.76 oz), install two balance weight sheets in line with each other (as shown in
the figure).
CAUTION:
Do not install one balance weight sheet on top of another.
3. Start wheel balancer again.
4. Install drive-in balance weight on inner side of road wheel in the wheel balancer indication position (angle).
CAUTION:
Do not install more than two balance weights.
5. Start wheel balancer. Make sure that inner and outer residual unbalance values are 5.0 g (0.18 oz) each or below.

If either residual unbalance value exceeds 5.0 g (0.18 oz), repeat installation procedures.
Wheel balance (Maximum allowable unbalance):
SMA054D
SEIA0271E
Maximum allowable
unbalance Dynamic (At rim flange) Less than 5.0 g (0.18 oz) (one side)
Static (At rim flange) Less than 20 g (0.71 oz)
SMA056D

WT-1
ROAD WHEELS & TIRES
E SUSPENSION
CONTENTS
C
D
F
G H
I
J
K L
M
SECTION WT
A
B
WT
Revision: 2005 July 2005 FX
ROAD WHEELS & TIRES
PREPARATION ........................................................... 2
Special Service Tools .......................................... ..... 2
Commercial Service Tools ................................... ..... 2
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING ........................................... ..... 3
NVH Troubleshooting Chart ................................ ..... 3
ROAD WHEEL ....................................................... ..... 4
Inspection ............................................................ ..... 4
ALUMINUM WHEEL ........................................ ..... 4
STEEL WHEEL ................................................ ..... 4
ROAD WHEEL TIRE ASSEMBLY ......................... ..... 5
Balancing Wheels (Bonding Weight Type) .......... ..... 5
REMOVAL ........................................................ ..... 5
WHEEL BALANCE ADJUSTMENT ................. ..... 5
Tire Rotation ........................................................ ..... 6
LOW TIRE PRESSURE WARNING SYSTEM ....... ..... 7
System Components ........................................... ..... 7
System Description ............................................. ..... 7
TRANSMITTER ................................................ ..... 7
REMOTE KEYLESS ENTRY RECEIVER ........ ..... 7
BCM (BODY CONTROL MODULE) ................. ..... 8
LOW TIRE PRESSURE WARNING LAMP ...... ..... 8
DISPLAY UNIT ................................................. ..... 8
CAN COMMUNICATION ....................................... ..... 9
System Description ............................................. ..... 9
TROUBLE DIAGNOSES ....................................... ... 10
Schematic ........................................................... ... 10
Wiring Diagram ................................................... .... 11
Control Unit Input/Output Signal Standard .......... ... 14
ID Registration Procedure ................................... ... 16
ID REGISTRATION WITH ACTIVATION TOOL ... 16
ID REGISTRATION WITHOUT ACTIVATION
TOOL ............................................................... ... 17
Transmitter Wake Up Operation .......................... ... 18
WITH ACTIVATION TOOL ............................... ... 18
Self-Diagnosis ..................................................... ... 19
DESCRIPTION ................................................. ... 19
FUNCTION ....................................................... ... 19
LOW TIRE PRESSURE WARNING LAMP DIAG-
NOSTIC CHART .............................................. ... 19 CONSULT-II ......................................................
... 20
WORK SUPPORT MODE ................................ ... 21
SELF-DIAGNOSTIC RESULTS MODE ............ ... 21
DATA MONITOR MODE ................................... ... 22
ACTIVE TEST MODE ...................................... ... 22
How to Perform Trouble Diagnosis for Quick and
Accurate Repair ................................................... ... 25
INTRODUCTION .............................................. ... 25
WORK FLOW ................................................... ... 25
Preliminary Check ............................................... ... 26
Malfunction Code/Symptom Chart ....................... ... 27
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS ..................................................................... ... 28
Inspection 1: Transmitter or Control Unit (BCM) .. ... 28
MALFUNCTION CODE NO. 21, 22, 23 OR 24 ... 28
Inspection 2: Transmitter - 1 ................................ ... 28
MALFUNCTION CODE NO. 31, 32, 33, 34, 41,
42, 43, 44, 45, 46, 47 OR 48 ............................ ... 28
Inspection 3: Transmitter - 2 ................................ ... 29
MALFUNCTION CODE NO. 35, 36, 37 OR 38 ... 29
Inspection 4: Vehicle Speed Signal ..................... ... 30
MALFUNCTION CODE NO. 52 ........................ ... 30
TROUBLE DIAGNOSIS FOR SYMPTOMS ........... ... 31
Inspection 1: Warning Lamp Does Not Come On
When Ignition Switch Is Turned On ..................... ... 31
Inspection 2: Warning Lamp Stays On When Ignition
Switch Is Turned On ............................................ ... 31
Inspection 3: Warning Lamp Blinks When Ignition
Switch Is Turned On ............................................ ... 33
Inspection 4: Turn Signal Lamp Blinks When Ignition
Switch Is Turned On ............................................ ... 34
Inspection 5: ID Registration Can Not Be Completed ... 34
REMOVAL AND INSTALLATION .......................... ... 35
Transmitter .......................................................... ... 35
REMOVAL ........................................................ ... 35
INSTALLATION ................................................ ... 35
SERVICE DATA ..................................................... ... 37
Road Wheel ......................................................... ... 37
Tire ...................................................................... ... 37
Tightening Torque ................................................ ... 37

ROAD WHEEL TIRE ASSEMBLY WT-5
C
D
F
G H
I
J
K L
M A
B
WT
Revision: 2005 July 2005 FX
ROAD WHEEL TIRE ASSEMBLYPFP:40300
Balancing Wheels (Bonding Weight Type)AES000JM
REMOVAL
1. Remove inner and outer balance weights from the road wheel.
CAUTION:
Be careful not to scratch the road wheel during removal.
2. Using releasing agent, remove double-faced adhesive tape from the road wheel. CAUTION:

Be careful not to scratch the road wheel during removal.

After removing double-faced adhesive tape, wipe clean traces of releasing agent from the road
wheel.
WHEEL BALANCE ADJUSTMENT

If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting,
select and adjust a drive-in weight mode suitable for road wheels.
1. Set road wheel on wheel balancer using the center hole as a guide. Start the tire balance machine.
2. When inner and outer unbalance values are shown on the wheel balancer indicator, multiply outer unbal- ance value by 5/3 to determine balance weight that should be used. Select the outer balance weight with
a value closest to the calculated value above and install it to the designated outer position of, or at the
designated angle in relation to the road wheel.
CAUTION:

Do not install the inner balance weight before installing the outer balance weight.

Before installing the balance weight, be sure to clean the
mating surface of the road wheel.
Indicated unbalance value × 5/3 = balance weight to be installed
Calculation example:
23 g (0.81 oz) × 5/3 = 38.33 g (1.35 oz) = 40 g (1.41 oz) balance
weight (closer to calculated balance weight value)
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
37.4 = 35 g (1.23 oz)
37.5 = 40 g (1.41 oz)
a. Install balance weight in the position shown in the figure.
b. When installing balance weight to road wheels, set it into the grooved area on the inner wall of the road wheel as shown in the
figure so that the balance weight center is aligned with the wheel
balancer indication position (angle).
CAUTION:

Always use genuine NISSAN adhesion balance weights.

Balance weights are unreusable; always replace with new
ones.

Do not install more than three sheets of balance weight.
SMA054D
SEIA0271E

WT-6
ROAD WHEEL TIRE ASSEMBLY
Revision: 2005 July 2005 FX
c. If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight sheets in line with each other (as shown in
the figure).
CAUTION:
Do not install one balance weight sheet on top of another.
3. Start wheel balancer again.
4. Install drive-in balance weight on inner side of road wheel in the wheel balancer indication position (angle).
CAUTION:
Do not install more than two balance weights.
5. Start wheel balancer. Make sure that inner and outer residual unbalance values are 5.0 g (0.2 oz) each or below.

If either residual unbalance value exceeds 5.0 g (0.2 oz), repeat installation procedures.
Wheel balance (Maximum allowable unbalance):
Tire RotationAES000ON

After rotating the tires, adjust the tire pressure.

Retighten the wheel nuts when the vehicle has been driven for
1,000 km (600 miles) (also in cases of a flat tire, etc.).
CAUTION:

Do not include the T-type spare tire when rotating the tires.

When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
Maximum allowable
unbalance Dynamic (At rim flange) 5.0 g (0.2 oz) (one side)
Static (At rim flange) 20 g (0.7 oz)
SMA056D
Tightening torque of wheel nut : 112.5 N·m (11 kg, 83 ft-lb)
SMA829C