2005 INFINITI FX35 display

REAR VIEW MONITOR DI-129
C
D E
F
G H
I
J
L
M A
B
DI
Revision: 2005 July 2005 FX
10. CHECK REAR VIEW CAMERA SIGNAL
1. Turn ignition switch OFF.
2. Connect rear view camera connector.
3. Turn ignition switch ON.
4. Shift A/T selector lever to R position.
5. Check voltage signal between rear view camera control unit har- ness connector M48 terminal 10 (G/W) and ground.
OK or NG
OK >> GO TO 11.
NG >> Replace rear view camera.
11 . CHECK COMPOSITE SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear view camera control unit connector and display connector.
3. Check continuity between rear view camera control unit harness connector M48 terminal 12 (BR) and display harness connector
M63 terminal 15 (BR).
4. Check continuity between rear view camera control unit harness connector M48 terminal 12 (BR) and ground.
OK or NG
OK >> GO TO 12.
NG >> Repair harness or connector.
12. CHECK COMPOSITE SIGNAL GROUND CIRCUIT
1. Check continuity between rear view camera control unit harness connector M48 terminal 11 and display harness connector M63
terminal 4.
2. Check continuity between rear view camera control unit harness connector M48 terminal 11 and ground.
OK or NG
OK >> GO TO 13.
NG >> Repair harness or connector. 10 (G/W) – Ground:
PKIB3582E
SKIA4894E
12 (BR) – 15 (BR) : Continuity should exist.
12 (BR) – Ground : Continuity should not exist.
SKIB0482E
11 – 4 : Continuity should exist.
11 – Ground : Continuity should not exist.
SKIA5102E

DI-130
REAR VIEW MONITOR
Revision: 2005 July 2005 FX
13. CHECK COMPOSITE SIGNAL
1. Connect rear view camera control unit connector and display connector.
2. Turn ignition switch ON.
3. Check voltage signal between rear view camera control unit har- ness connector M48 terminal 12 (BR) and ground.
OK or NG
OK >> Replace display.
NG >> Replace rear view camera control unit.
The Rear View Image Is DistortedAKS0068P
1. CHECK SYNCHRO SIGNAL OPEN OR SHORT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear view camera control unit connector and display connector.
3. Check continuity between rear view camera control unit harness connector M48 terminal 14 (Y) and display harness connector
M63 terminal 16 (Y)
4. Check continuity between rear view camera control unit harness connector M48 terminal 14 (Y) and ground
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2. CHECK COMPOSITE SIGNAL GROUND CIRCUIT
1. Check continuity between rear view camera control unit harness connector M48 terminal 11 and display harness connector M63
terminal 4.
2. Check continuity between rear view camera control unit harness connector M48 terminal 11 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector. 12 (BR) – Ground:
PKIB3583E
SKIA4896E
14 (Y) – 16 (Y) : Continuity should exist.
14 (Y) – Ground : Continuity should not exist.
SKIA5101E
11 – 4 : Continuity should exist.
11 – Ground : Continuity should not exist.
SKIA5102E

REAR VIEW MONITOR DI-131
C
D E
F
G H
I
J
L
M A
B
DI
Revision: 2005 July 2005 FX
3. CHECK REAR VIEW CONTROL UNIT SYNCHRO SIGNAL
1. Connect rear view camera control unit connector and display connector.
2. Turn ignition switch ON.
3. Check voltage signal between rear view camera control unit har- ness connector M48 terminal 14 (Y) and ground.
OK or NG
OK >> Replace rear view camera control unit.
NG >> Replace display.
Removal and Installation of Rear View Camera Control UnitAKS0068Q
REMOVAL
1. Remove instrument clock finisher and A/T console finisher. Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
2. Remove screws (2), and remove rear view camera control unit.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Rear View CameraAKS0068R
REMOVAL
1. Remove back door finisher lower. Refer to EI-45, "Removal and
Installation" .
2. Cut off back door module along the line.
3. Disconnect rear view camera connector. 14 (Y) – Ground:
PKIB3584E
SKIA5896E
SKIA5797E
SKIA6168E

INDEX FOR DTC EC-15
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2005 July 2005 FX
[VQ35DE]INDEX FOR DTCPFP:00024
DTC No. IndexABS006JW
NOTE:
If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000,
U1001. Refer to EC-171, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .
DTC*1
Items
(CONSULT-II screen terms) Reference page
CONSULT-II
GST*
2ECM*3
U1000 1000*4CAN COMM CIRCUIT EC-171
U1001
1001*4CAN COMM CIRCUIT EC-171
P0000 0000 NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED. —
P0011 0011 INT/V TIM CONT-B1 EC-174
P0021 0021 INT/V TIM CONT-B2 EC-174
P0037 0037 HO2S2 HTR (B1)EC-178
P0038 0038 HO2S2 HTR (B1)EC-178
P0057 0057 HO2S2 HTR (B2)EC-178
P0058 0058 HO2S2 HTR (B2)EC-178
P0101 0101 MAF SEN/CIRCUITEC-186
P0102 0102 MAF SEN/CIRCUITEC-195
P0103 0103 MAF SEN/CIRCUITEC-195
P0112 0112 IAT SEN/CIRCUITEC-203
P0113 0113 IAT SEN/CIRCUITEC-203
P0117 0117 ECT SEN/CIRCUITEC-208
P0118 0118 ECT SEN/CIRCUITEC-208
P0122 0122 TP SEN 2/CIRC EC-213
P0123 0123 TP SEN 2/CIRCEC-213
P0125 0125 ECT SENSOREC-220
P0127 0127 IAT SENSOREC-223
P0128 0128 THERMSTAT FNCTNEC-226
P0138 0138 HO2S2 (B1)EC-228
P0139 0139 HO2S2 (B1)EC-237
P0158 0158 HO2S2 (B2)EC-228
P0159 0159 HO2S2 (B2)EC-237
P0171 0171 FUEL SYS-LEAN-B1EC-248
P0172 0172 FUEL SYS-RICH-B1EC-258
P0174 0174 FUEL SYS-LEAN-B2EC-248
P0175 0175 FUEL SYS-RICH-B2EC-258
P0181 0181 FTT SENSOREC-267
P0182 0182 FTT SEN/CIRCUITEC-273
P0183 0183 FTT SEN/CIRCUITEC-273
P0222 0222 TP SEN 1/CIRCEC-278
P0223 0223 TP SEN 1/CIRCEC-278
P0300 0300 MULTI CYL MISFIREEC-285
P0301 0301 CYL 1 MISFIREEC-285

INDEX FOR DTC EC-19
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2005 July 2005 FX
Alphabetical IndexABS006JV
NOTE:
If DTC U1000 or U1001 is displayed with other DTC, first perform the trouble diagnosis for DTC U1000,
U1001. Refer to EC-171, "
DTC U1000, U1001 CAN COMMUNICATION LINE" .
Items
(CONSULT-II screen terms) DTC*
1
Reference page
CONSULT-II
GST*
2ECM*3
A/F SENSOR1 (B1) P1271 1271 EC-488
A/F SENSOR1 (B1) P1272 1272EC-497
A/F SENSOR1 (B1) P1273 1273EC-506
A/F SENSOR1 (B1) P1274 1274EC-516
A/F SENSOR1 (B1) P1276 1276EC-526
A/F SENSOR1 (B1) P1278 1278EC-536
A/F SENSOR1 (B1) P1279 1279EC-548
A/F SENSOR1 (B2) P1281 1281EC-488
A/F SENSOR1 (B2) P1282 1282EC-497
A/F SENSOR1 (B2) P1283 1283EC-506
A/F SENSOR1 (B2) P1284 1284EC-516
A/F SENSOR1 (B2) P1286 1286EC-526
A/F SENSOR1 (B2) P1288 1288EC-536
A/F SENSOR1 (B2) P1289 1289EC-548
A/F SEN1 HTR (B1) P1031 1031EC-405
A/F SEN1 HTR (B1) P1032 1032EC-405
A/F SEN1 HTR (B2) P1051 1051EC-405
A/F SEN1 HTR (B2) P1052 1052EC-405
A/T INTERLOCK P1730 1730 AT- 1 4 5
A/T TCC S/V FNCTN P0744 0744AT- 1 2 7
ICC COMMAND VALUE*7P1568 1568EC-587
APP SEN 1/CIRC P2122 2122 EC-619
APP SEN 1/CIRC P2123 2123EC-619
APP SEN 2/CIRC P2127 2127EC-626
APP SEN 2/CIRC P2128 2128EC-626
APP SENSOR P2138 2138EC-640
ASCD BRAKE SW*6P1572 1572EC-588, EC-597
ASCD SW*6P1564 1564 EC-574, EC-581
ASCD VHL SPD SEN*6P1574 1574 EC-605, EC-607
ATF TEMP SEN/CIRC P0710 0710 AT- 1 3 6
BRAKE SW/CIRCUIT P1805 1805EC-614
CAN COMM CIRCUIT U1000
1000*4EC-171
CAN COMM CIRCUIT U1001 1001*4EC-171
CKP SEN/CIRCUIT P0335 0335 EC-300
CLOSED LOOP-B1 P1148 1148EC-464
CLOSED LOOP-B2 P1168 1168EC-464
CMP SEN/CIRC-B1 P0340 0340EC-307
CMP SEN/CIRC-B2 P0345 0345EC-307

PRECAUTIONS EC-25
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2005 July 2005 FX

Before replacing ECM, perform “ECM Terminals and Refer-
ence Value” inspection and make sure ECM functions prop-
erly. Refer to EC-123
.

Handle mass air flow sensor carefully to avoid damage.

Do not disassemble mass air flow sensor.

Do not clean mass air flow sensor with any type of deter-
gent.

Do not disassemble electric throttle control actuator.

Even a slight leak in the air intake system can cause seri-
ous incidents.

Do not shock or jar the camshaft position sensor (PHASE),
crankshaft position sensor (POS).

After performing each TROUBLE DIAGNOSIS, perform DTC
Confirmation Procedure or Overall Function Check.
The DTC should not be displayed in the DTC Confirmation
Procedure if the repair is completed. The Overall Function
Check should be a good result if the repair is completed.

When measuring ECM signals with a circuit tester, never
allow the two tester probes to contact.
Accidental contact of probes will cause a short circuit and
damage the ECM power transistor.

Do not use ECM ground terminals when measuring input/
output voltage. Doing so may result in damage to the ECM's
transistor. Use a ground other than ECM terminals, such as
the ground.
MEF040D
SEF217U
SEF348N

EC-44
[VQ35DE]
EVAPORATIVE EMISSION SYSTEM
Revision: 2005 July 2005 FX
WITH CONSULT-II
1. Attach the EVAP service port adapter securely to the EVAP service port.
2. Also attach the pressure pump and hose to the EVAP service port adapter.
3. Turn ignition switch ON.
4. Select the “EVAP SYSTEM CLOSE” of “WORK SUPPORT MODE” with CONSULT-II.
5. Touch “START”. A bar graph (Pressure indicating display) will appear on the screen.
6. Apply positive pressure to the EVAP system until the pressure indicator reaches the middle of the bar graph.
7. Remove EVAP service port adapter and hose with pressure pump.
8. Locate the leak using a leak detector. Refer to EC-40, "
EVAPO-
RATIVE EMISSION LINE DRAWING" .
WITHOUT CONSULT-II
1. Attach the EVAP service port adapter securely to the EVAP ser-
vice port.
2. Also attach the pressure pump with pressure gauge to the EVAP service port adapter.
PEF838U
PEF917U
SEF200U
SEF462UA

IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS) EC-53
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2005 July 2005 FX
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)PFP:28591
DescriptionABS00E90

If the security indicator lights up with the ignition switch in
the ON position or “NATS MALFUNCTION” is displayed on
“SELF-DIAG RESULTS” screen, perform self-diagnostic
results mode with CONSULT-II using NATS program card.
Refer to BL-213, "
IVIS (INFINITI VEHICLE IMMOBILIZER
SYSTEM-NATS)" .

Confirm no self-diagnostic results of IVIS (NATS) is dis-
played before touching “ERASE” in “SELF-DIAG RESULTS”
mode with CONSULT-II.

When replacing ECM, initialization of IVIS (NATS) system
and registration of all IVIS (NATS) ignition key IDs must be
carried out with CONSULT-II using NATS program card.
Therefore, be sure to receive all keys from vehicle owner. Regarding the procedures of IVIS (NATS)
initialization and all IVIS (NATS) ignition key ID registration, refer to CONSULT-II Operation Manual,
IVIS/NVIS.
SEF543X