2005 INFINITI FX35 lock

TROUBLE DIAGNOSIS AT-73
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX26
Slips/Will
Not
Engage Lock-up is not
released.
Refer to AT-221,
"Lock-up Is Not
Released" . ON vehicle 1. A/T fluid level and state
AT- 5 2
2. Line pressure testAT- 5 4
3. Engine speed signalAT-123
4. Turbine revolution sensorAT-141
5. Torque converter clutch solenoid valveAT-125
6. CAN communication lineAT-106
7. Control valve with TCMAT-243
OFF vehicle 8. Torque converter
AT-2909. Oil pump assemblyAT-308
27 No shock at all or the
clutch slips when
vehicle changes
speed D
1 → D2 or
M
1 → M2 . ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT-143
3. ATF pressure switch 5 and direct clutch solenoid valve AT-179,
AT-158
4. CAN communication line AT-106
5. Line pressure test AT- 5 4
6. Control valve with TCMAT-243
OFF vehicle 7. Torque converter
AT-290
8. Oil pump assemblyAT-308
9. 3rd one-way clutch AT- 3 11
10. Gear systemAT-278
11. Direct clutchAT-326
12. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-18,
"Cross-Sectional View (2WD Models)" or AT-19, "Cross-
Sectional View (AWD Models)" ) AT-290
No. Items Symptom Condition Diagnostic Item
Reference
page

AT-80
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
40
Slips/Will
Not
Engage While accelerating in
4th, engine races or
slippage occurs. ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Line pressure testAT- 5 4
3. Accelerator pedal position sensorAT- 1 3 3
4. CAN communication lineAT- 1 0 6
5. ATF pressure switch 3 and input clutch solenoid valve AT- 1 7 7,
AT- 1 5 0
6. Control valve with TCM AT- 2 4 3
OFF vehicle 7. Torque converter
AT- 2 9 0
8. Oil pump assemblyAT- 3 0 8
9. Input clutchAT- 3 1 3
10. Gear systemAT- 2 7 8
11. High and low reverse clutchAT- 3 2 3
12. Direct clutchAT- 3 2 6
41 While accelerating in
5th, engine races or
slippage occurs. ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Line pressure testAT- 5 4
3. Accelerator pedal position sensorAT- 1 3 3
4. CAN communication lineAT- 1 0 6
5. ATF pressure switch 1 and front brake solenoid valve AT- 1 7 5,
AT- 1 5 4
6. Control valve with TCM AT- 2 4 3
OFF vehicle 7. Torque converter
AT- 2 9 0
8. Oil pump assembly AT- 3 0 8
9. Front brake (brake band)AT- 2 9 0
10. Input clutchAT- 3 1 3
11. Gear systemAT- 2 7 8
12. High and low reverse clutchAT- 3 2 3
42 Slips at lock-up. ON vehicle 1. A/T fluid level and state
AT- 5 2
2. Line pressure testAT- 5 4
3. Engine speed signalAT- 1 2 3
4. Turbine revolution sensorAT- 1 4 1
5. Torque converter clutch solenoid valveAT- 1 2 5
6. CAN communication lineAT- 1 0 6
7. Control valve with TCMAT- 2 4 3
OFF vehicle 8. Torque converter
AT- 2 9 09. Oil pump assemblyAT- 3 0 8
No. Items Symptom Condition Diagnostic Item Reference
page

AT-84
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
53
Others Shift point is low in “D”
position. ON vehicle 1. Vehicle speed sensor A/T and vehicle speed sensor MTR
AT- 11 8
,
AT- 1 4 3
2. Accelerator pedal position sensor AT- 1 3 3
3. CAN communication lineAT- 1 0 6
4. Control valve with TCMAT- 2 4 3
54 Judder occurs during
lock-up. ON vehicle 1. A/T fluid level and state
AT- 5 2
2. Engine speed signalAT- 1 2 3
3. Turbine revolution sensorAT- 1 4 1
4. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT- 1 4 3
5. Accelerator pedal position sensor AT- 1 3 3
6. CAN communication lineAT- 1 0 6
7. Torque converter clutch solenoid valveAT- 1 2 5
8. Control valve with TCMAT- 2 4 3
OFF vehicle 9. Torque converter AT- 2 9 0
55 Strange noise in “R”
position. ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Engine speed signalAT- 1 2 3
3. CAN communication lineAT- 1 0 6
4. Control valve with TCMAT- 2 4 3
OFF vehicle 5. Torque converter
AT- 2 9 0
6. Oil pump assemblyAT- 3 0 8
7. Gear systemAT- 2 7 8
8. High and low reverse clutchAT- 3 2 3
9. Reverse brakeAT- 2 9 0
56 Strange noise in “N”
position. ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Engine speed signalAT- 1 2 3
3. CAN communication lineAT- 1 0 6
4. Control valve with TCMAT- 2 4 3
OFF vehicle 5. Torque converter
AT- 2 9 06. Oil pump assemblyAT- 3 0 8
7. Gear systemAT- 2 7 8
No. Items Symptom Condition Diagnostic Item Reference
page

AT-90
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
CONSULT-II Function (A/T)ACS002M9
CONSUT-II can display each diagnostic item using the diagnostic test models shown following.
FUNCTION
CONSULT-II REFERENCE VALUE
NOTICE:
1. The CONSULT-II electrically displays shift timing and lock-up timing (that is, operation timing of each sole-
noid).
Check for time difference between actual shift timing and the CONSULT-II display. If the difference is
noticeable, mechanical parts (except solenoids, sensors, etc.) may be malfunctioning. Check mechanical
parts using applicable diagnostic procedures.
2. Shift schedule (which implies gear position) displayed on CONSULT-II and that indicated in Service Man- ual may differ slightly. This occurs because of the following reasons:
–Actual shift schedule has more or less tolerance or allowance,
–Shift schedule indicated in Service Manual refers to the point where shifts start, and
–Gear position displayed on CONSULT-II indicates the point where shifts are completed.
3. Display of solenoid valves on CONSULT-II changes at the start of shifting, while gear position is displayed upon completion of shifting (which is computed by TCM).
Diagnostic test mode Function Reference page
Self-diagnostic results Self-diagnostic results can be read and erased quickly. AT- 9 3
Data monitor Input/Output data in the ECU can be read.AT- 9 6
CAN diagnostic support
monitor The results of transmit/receive diagnosis of CAN communication can be read.
AT- 1 0 0
Function test Performed by CONSULT-II instead of a technician to determine whether each system
is “OK” or “NG”. —
DTC work support Select the operating condition to confirm Diagnosis Trouble Codes. AT- 1 0 0
ECU part number ECU part number can be read. —
Item name Condition Display value
(Approx.)
VHCL/S SE·A/T During driving Approximately
matches the speed-
ometer reading.
VHCL/S SE·MTR
ACCELE POSI Released accelerator pedal. 0.0/8
Fully depressed accelerator pedal. 8/8
CLSD THL POS Released accelerator pedal. ON
Fully depressed accelerator pedal. OFF
W/O THL POS Fully depressed accelerator pedal. ON
Released accelerator pedal. OFF
BRAKE SW Depressed brake pedal. ON
Released brake pedal. OFF
ENGINE SPEED Engine running Closely matches the
tachometer reading.
TURBINE REV During driving (lock-up ON) Approximately
matches the engine
speed.
ATF TEMP SE 1 0 °C (32 ° F) - 20 °C (68 °F) - 80 °C (176 °F) 3.3 - 2.7 - 0.9 V
ATF TEMP SE 2 3.3 - 2.5 - 0.7 V
TCC SOLENOID When performing slip lock-up 0.2 - 0.4 A
When performing lock-up 0.4 - 0.6 A
LINE PRES SOL During driving 0.2 - 0.6 A

TROUBLE DIAGNOSIS AT-93
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
SELF-DIAGNOSTIC RESULT MODE
After performing AT- 9 3 , "SELF-DIAGNOSTIC RESULT MODE" , place check marks for results on the AT- 4 7 ,
"DIAGNOSTIC WORKSHEET" . Reference pages are provided following the items.
Operation Procedure
1. Perform “CONSULT-II SETTING PROCEDURE”. Refer to AT- 9 2 , "CONSULT-II SETTING PROCEDURE"
.
2. Touch “SELF-DIAG RESULTS”. Display shows malfunction experienced since the last erasing
operation.
Display Items List
X: Applicable, —: Not applicable
BCIA0031E
Items (CONSULT-II
screen terms) Malfunction is detected when... TCM self-
diagnosis OBD-II
(DTC)
Reference page
“A/T” with
CONSULT- II MIL indica-
tor lamp*1, “ENGINE”
with CON- SULT-II or GST
CAN COMM CIR-
CUIT

When a malfunction is detected in CAN communications U1000 U1000 AT- 1 0 6
STARTER RELAY/
CIRC

If this signal is ON other than in “P” or “N” position, this is judged
to be a malfunction.
(And if it is OFF in “P” or “N” position, this too is judged to be a
malfunction.) P0615 —
AT- 1 0 9
TCM
TCM is malfunctioning P0700 P0700*3 AT- 11 3
PNP SW/CIRC

PNP switch 1-4 signals input with impossible pattern

“P” position is detected from “N” position without any other posi-
tion being detected in between. P0705 P0705
AT- 11 4
VEH SPD SEN/CIR
AT (Revolution
sensor)

Signal from vehicle speed sensor A/T (Revolution sensor) not
input due to cut line or the like

Unexpected signal input during running

After ignition switch is turned ON, unexpected signal input from
vehicle speed sensor MTR before the vehicle starts moving P0720 P0720
AT- 11 8
ENGINE SPEED
SIG
TCM does not receive the CAN communication signal from the
ECM. P0725 P0725*3
AT- 1 2 3
TCC SOLENOID/
CIRC
Normal voltage not applied to solenoid due to cut line, short, or
the like P0740 P0740
AT- 1 2 5
A/T TCC S/V
FNCTN
A/T cannot perform lock-up even if electrical circuit is good.

TCM detects as irregular by comparing difference value with slip
rotation. P0744 P0744*2
AT- 1 2 7
L/PRESS SOL/
CIRC

Normal voltage not applied to solenoid due to cut line, short, or
the like

TCM detects as irregular by comparing target value with monitor
value. P0745 P0745
AT- 1 2 9
TCM·RAM
TCM memory (RAM) is malfunctioning. P1702 — AT- 1 3 1

AT-94
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
TCM·ROM
TCM memory (ROM) is malfunctioning. P1703 —AT-132
TP SEN/CIRC A/T
TCM does not receive the proper accelerator pedal position sig-
nals (input by CAN communication) from ECM. P1705 P1705*3
AT-133
ATF TEMP SEN/
CIRC
During running, the AT fluid temperature sensor signal voltage is
excessively high or low P1710 P0710
AT-136
TURBINE REV S/
CIRC
TCM does not receive the proper voltage signal from the sensor.

TCM detects an irregularity only at position of 4th gear for turbine
revolution sensor 2. P1716 P1716
AT-141
VEH SPD SE/
CIR·MTR
Signal (CAN communication) from vehicle speed sensor MTR not
input due to cut line or the like

Unexpected signal input during running P1721 —
AT-143
A/T INTERLOCK
Except during shift change, the gear position and ATF pressure
switch states are monitored and comparative judgement made. P1730 P1730
AT-145
A/T 1ST E/BRAK-
ING
Each ATF pressure switch and solenoid current is monitored and
if a pattern is detected having engine braking 1st gear other than
in the M1 position, a malfunction is detected. P1731 —
AT-148
I/C SOLENOID/
CIRC

Normal voltage not applied to solenoid due to functional malfunc-
tion, cut line, short, or the like

TCM detects as irregular by comparing target value with monitor
value. P1752 P1752
AT-150
I/C SOLENOID
FNCTN

TCM detects that actual gear ratio is irregular, and relation
between gear position and condition of ATF pressure switch 3 is
irregular during depressing accelerator pedal. (Other than during
shift change)

TCM detects that relation between gear position and condition of
ATF pressure switch 3 is irregular during releasing accelerator
pedal. (Other than during shift change) P1754 P1754*2
AT-152
FR/B SOLENOID/
CIRC

Normal voltage not applied to solenoid due to functional malfunc-
tion, cut line, short, or the like

TCM detects as irregular by comparing target value with monitor
value. P1757 P1757
AT-154
FR/B SOLENOID
FNCT

TCM detects that actual gear ratio is irregular, and relation
between gear position and condition of ATF pressure switch 1 is
irregular during depressing accelerator pedal. (Other than during
shift change)

TCM detects that relation between gear position and condition of
ATF pressure switch 1 is irregular during releasing accelerator
pedal. (Other than during shift change) P1759 P1759*2
AT-156
D/C SOLENOID/
CIRC

Normal voltage not applied to solenoid due to cut line, short, or
the like

TCM detects as irregular by comparing target value with monitor
value. P1762 P1762
AT-158
Items (CONSULT-II
screen terms) Malfunction is detected when... TCM self-
diagnosis OBD-II
(DTC)
Reference page
“A/T” with
CONSULT- II MIL indica-
tor lamp*1, “ENGINE”
with CON- SULT-II or GST

AT-102
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
7. Perform test drive to check gear shift feeling in accordance with
instructions displayed.
8. Touch “YES” or “NO”.
9. CONSULT-II procedure is ended.

If “NG” appears on the screen, a malfunction may exit.
Go to “Diagnostic Procedure”
Display Items List
*: Do not use, but displayed.
SCIA5163E
SCIA5162E
DTC work support item Description Check item
I/C SOL FUNCTN CHECK* — —
FR/B SOL FUNCTN CHECK* — —
D/C SOL FUNCTN CHECK* — —
HLR/C SOL FUNCTN CHECK* — —
LC/B SOL FUNCTN CHECK* — —
TCC SOL FUNCTN CHECK Following items for “TCC solenoid function (lock-up) ” can be con-
firmed.

Self-diagnosis status (whether the diagnosis is being performed
or not)

Self-diagnosis results (OK or NG)

TCC solenoid valve

Hydraulic control circuit

TROUBLE DIAGNOSIS AT-103
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
Diagnostic Procedure without CONSULT-IIACS008CZ
OBD-II SELF-DIAGNOSTIC PROCEDURE (WITH GST)
Refer to EC-144, "Generic Scan Tool (GST) Function" (for VQ35DE) or EC-835, "Generic Scan Tool (GST)
Function" (for VK45DE).
OBD-II SELF-DIAGNOSTIC PROCEDURE (NO TOOLS)
Refer to EC-69, "Malfunction Indicator Lamp (MIL)" (for VQ35DE) or EC-760, "Malfunction Indicator Lamp
(MIL)" (for VK45DE).
TCM SELF-DIAGNOSTIC PROCEDURE (NO TOOLS)
Description
In the unlikely event of a malfunction in the electrical system, when the ignition switch is switched “ON”, the A/
T CHECK indicator lamp lights up for 2 seconds, then flashes for 8 seconds. If there is no malfunction, when
the ignition switch is turned “ON”, the indicator lamp lights up for 2 seconds. As a method for locating the sus-
pect circuit, when the self-diagnostics start signal is input, the memory for the malfunction location is output
and the A/T CHECK indicator lamp flashes to display the corresponding DTC.
Diagnostic Procedure
1. CHECK A/T CHECK INDICATOR LAMP
1. Start the engine with selector lever in “P” position. Warm engine to normal operating temperature.
2. Turn ignition switch “ON” and “OFF” at least twice, then leave it in the “OFF” position.
3. Wait 10 seconds.
4. Turn ignition switch “ON”. (Do not start engine.)
Does A/T CHECK indicator lamp come on for about 2 seconds?
YES >> GO TO 2.
NO >> GO TO AT- 1 9 3
.
2. JUDGEMENT PROCEDURE STEP 1
1. Turn ignition switch “OFF”.
2. Push shift lock release button.
3. Move selector lever from “P” to “D” position.
4. Release accelerator pedal. (Set the closed throttle position signal “ON”.)
5. Depress brake pedal. (Stop lamp switch signal “ON”.)
6. Turn ignition switch “ON”. (Do not start engine.)
7. Wait 3 seconds.
>> GO TO 3.
3. JUDGEMENT PROCEDURE STEP 2
1. Move the selector lever to the manual shift gate side. (Manual mode switch “ON”.)
2. Release brake pedal. (Stop lamp switch signal “OFF”.)
3. Move the selector lever to “D” position. (Manual mode switch “OFF”.)
4. Depress brake pedal. (Stop lamp switch signal “ON”.)
5. Release brake pedal. (Stop lamp switch signal “OFF”.)
6. Depress accelerator pedal fully and release it.
>> GO TO 4.