2005 INFINITI FX35 diagram

AT-188
BRAKE SIGNAL CIRCUIT
Revision: 2005 July 2005 FX
BRAKE SIGNAL CIRCUITPFP:25320
CONSULT-II Reference ValueACS006CS
Diagnostic ProcedureACS002R3
1. CHECK CAN COMMUNICATION LINE
Perform the self-diagnosis. Refer to AT- 9 3 , "
SELF-DIAGNOSTIC RESULT MODE" , AT- 1 0 3 , "Diagnostic Pro-
cedure without CONSULT-II" .
Is a malfunction in the CAN communication indicated in the results?
YES >> Check CAN communication line. Refer to AT- 1 0 6 , "DTC U1000 CAN COMMUNICATION LINE" .
NO >> GO TO 2.
2. CHECK STOP LAMP SWITCH CIRCUIT
With CONSULT-II
1. Turn ignition switch ON. (Do not start engine.)
2. Select “ECU INPUT SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT-II.
3. Read out ON/OFF switching action of the “BRAKE SW”.
OK or NG
OK >> INSPECTION END
NG >> GO TO 3.
3. CHECK STOP LAMP SWITCH
Check continuity between stop lamp switch harness connector termi-
nals 1 and 2. Refer to AT- 1 9 0 , "
Wiring Diagram — AT — NONDTC" .
Check stop lamp switch after adjusting brake pedal — refer to
BR-6, "
BRAKE PEDAL" .
OK or NG
OK >> Check the following items. If NG, repair or replace dam- aged parts.

Harness for short or open between battery and stop lamp switch.

Harness for short or open between stop lamp switch and unified meter and A/C amp.
NG >> Repair or replace the stop lamp switch.
Item name Condition Display value
BRAKE SW Depressed brake pedal. ON
Released brake pedal. OFF
Item name Condition Display value
BRAKE SW Depressed brake pedal. ON
Released brake pedal. OFF
PCIA0070E
Condition Continuity
When brake pedal is depressed Yes When brake pedal is released No
SCIA2144E

AT-190
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2005 July 2005 FX
TROUBLE DIAGNOSIS FOR SYMPTOMSPFP:00007
Wiring Diagram — AT — NONDTCACS0080R
TCWM0254E

A/T SHIFT LOCK SYSTEM AT-237
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
Wiring Diagram — AT — SHIFTACS002RV
TCWM0386E

AT-238
A/T SHIFT LOCK SYSTEM
Revision: 2005 July 2005 FX
Diagnostic ProcedureACS002RW
SYMPTOM 1:

Selector lever cannot be moved from “P” position with key in ON position and brake pedal
applied.

Selector lever can be moved from “P” position with key in ON position and brake pedal released.

Selector lever can be moved from “P” position when key is removed from key cylinder.
SYMPTOM 2:

Ignition key cannot be removed when selector lever is set to “P” position.

Ignition key can be removed when selector lever is set to any position except “P” position.
1. CHECK KEY INTERLOCK CABLE
Check the key interlock cable for damage.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace key interlock cable. Refer to AT- 2 4 0 , "
KEY INTERLOCK CABLE" .
2. CHECK SELECTOR LEVER POSITION
Check the selector lever position for damage. Refer to AT- 2 3 5 , "
Checking of A/T Position"
OK or NG
OK >> GO TO 3.
NG >> Adjust control linkage. Refer to AT- 2 3 5 , "
Adjustment of A/T Position" .
3. CHECK SHIFT LOCK SOLENOID AND PARK POSITION SWITCH
1. Connect A/T device harness connector.
2. Turn ignition switch ON.
3. Selector lever is set in “P” position.
4. Check operation sound.
OK or NG
OK >> INSPECTION END
NG >> GO TO 4.
4. CHECK POWER SOURCE
1. Turn ignition switch ON. (Do not start engine.)
2. Check the voltage between A/T device harness connector termi- nal 1 and ground. Refer to AT- 2 3 7 , "
Wiring Diagram — AT —
SHIFT" .
OK or NG
OK >> GO TO 7.
NG >> GO TO 5.
Condition Brake pedal Operation sound
When ignition switch is turned to
ON and selector lever is set in
“P” position. Depressed Yes
Released No
Condition Brake pedal Data (Approx.)
When ignition switch is turned to
ON. Depressed Battery voltage
Released 0V
SCIA2122E

ATC-2Revision: 2005 July 2005 FX
MODE SWITCH ................................................
... 35
FAN SWITCH ................................................... ... 35
DUAL SWITCH (WITH LEFT AND RIGHT VEN-
TILATION TEMPERATURE SEPARATELY
CONTROL SYSTEM) ....................................... ... 35
Fail-safe Function ................................................ ... 36
Discharge Air Flow .............................................. ... 37
System Description .............................................. ... 38
SWITCHES AND THEIR CONTROL FUNCTION ... 38
CAN Communication System Description ........... ... 39
TROUBLE DIAGNOSIS ......................................... ... 40
CONSULT-II Function (BCM) ............................... ... 40
CONSULT-II BASIC OPERATION .................... ... 40
DATA MONITOR ............................................... ... 41
How to Perform Trouble Diagnosis for Quick and
Accurate Repair ................................................... ... 42
WORK FLOW ................................................... ... 42
SYMPTOM TABLE ........................................... ... 42
Component Parts and Harness Connector Location ... 43
ENGINE COMPARTMENT ............................... ... 43
PASSENGER COMPARTMENT ....................... ... 44
Schematic ............................................................ ... 45
Wiring Diagram —A/C— ...................................... ... 46
Auto Amp. Terminals and Reference Value ......... ... 51
PIN CONNECTOR TERMINAL LAYOUT ......... ... 51
TERMINALS AND REFERENCE VALUE FOR
UNIFIED METER AND A/C AMP. ..................... ... 51
Self-diagnosis Function ....................................... ... 53
DESCRIPTION ................................................. ... 53
FUNCTION CONFIRMATION PROCEDURE ... ... 54
AUXILIARY MECHANISM: TEMPERATURE
SETTING TRIMMER ........................................ ... 59
AUXILIARY MECHANISM: FOOT POSITION
SETTING TRIMMER ........................................ ... 60
AUXILIARY MECHANISM: INLET PORT MEM-
ORY FUNCTION .............................................. ... 60
Operational Check ............................................... ... 61
CHECKING MEMORY FUNCTION .................. ... 61
CHECKING BLOWER ...................................... ... 61
CHECKING DISCHARGE AIR ......................... ... 61
CHECKING INTAKE AIR .................................. ... 62
CHECKING TEMPERATURE DECREASE ...... ... 62
CHECKING TEMPERATURE INCREASE ....... ... 62
CHECK A/C SWITCH ....................................... ... 62
CHECKING AUTO MODE ................................ ... 63
Power Supply and Ground Circuit for Auto Amp. ... 63 INSPECTION FLOW ........................................ ... 63
COMPONENT DESCRIPTION ......................... ... 64
DIAGNOSIS PROCEDURE FOR A/C SYSTEM ... 64
LAN System Circuit ............................................. ... 66
DIAGNOSIS PROCEDURE FOR LAN CIRCUIT ... 66
Mode Door Motor Circuit ..................................... ... 70
INSPECTION FLOW ........................................ ... 70
SYSTEM DESCRIPTION ................................. ... 71
COMPONENT DESCRIPTION ......................... ... 72
DIAGNOSIS PROCEDURE FOR MODE DOOR
MOTOR ............................................................ ... 72
Air Mix Door Motor Circuit ................................... ... 73
INSPECTION FLOW ........................................ ... 73 SYSTEM DESCRIPTION ..................................
... 74
COMPONENT DESCRIPTION ......................... ... 75
DIAGNOSIS PROCEDURE FOR AIR MIX DOOR
MOTOR ............................................................. ... 75
Air Mix Door Motor PBR Circuit ........................... ... 75
DIAGNOSIS PROCEDURE FOR AIR MIX DOOR
MOTOR PBR .................................................... ... 75
Intake Door Motor Circuit ..................................... ... 76
INSPECTION FLOW ......................................... ... 76
SYSTEM DESCRIPTION .................................. ... 77
COMPONENT DESCRIPTION ......................... ... 78
DIAGNOSIS PROCEDURE FOR INTAKE DOOR
MOTOR ............................................................. ... 78
Blower Motor Circuit ............................................. ... 79
INSPECTION FLOW ......................................... ... 79
SYSTEM DESCRIPTION .................................. ... 80
COMPONENT DESCRIPTION ......................... ... 81
DIAGNOSIS PROCEDURE FOR BLOWER
MOTOR ............................................................. ... 81
COMPONENT INSPECTION ............................ ... 83
Magnet Clutch Circuit ........................................... ... 84
INSPECTION FLOW ......................................... ... 84
SYSTEM DESCRIPTION .................................. ... 85
DIAGNOSIS PROCEDURE FOR MAGNET
CLUTCH ........................................................... ... 85
COMPONENT INSPECTION ............................ ... 90
Insufficient Cooling ............................................... ... 91
INSPECTION FLOW ......................................... ... 91
PERFORMANCE TEST DIAGNOSIS ............... ... 93
PERFORMANCE CHART ................................. ... 95
TROUBLE DIAGNOSIS FOR UNUSUAL PRES-
SURE ................................................................ ... 96
DIAGNOSIS PROCEDURE FOR INSUFFI-
CIENT COOLING .............................................. ... 98
Insufficient Heating .............................................. .100
INSPECTION FLOW ......................................... .100
Noise .................................................................... .101
INSPECTION FLOW ......................................... .101
Self-diagnosis ...................................................... .102
INSPECTION FLOW ......................................... .102
Memory Function ................................................. .103
INSPECTION FLOW ......................................... .103
Ambient Sensor Circuit ........................................ .104
COMPONENT DESCRIPTION ......................... .104
AMBIENT TEMPERATURE INPUT PROCESS .104
DIAGNOSIS PROCEDURE FOR AMBIENT
SENSOR ........................................................... .104
COMPONENT INSPECTION ............................ .106
In-vehicle Sensor Circuit ...................................... .107
COMPONENT DESCRIPTION ......................... .107
DIAGNOSIS PROCEDURE FOR IN-VEHICLE
SENSOR ........................................................... .108
COMPONENT INSPECTION ............................ .109
Sunload Sensor Circuit ........................................ .110
COMPONENT DESCRIPTION ......................... .110
SUNLOAD INPUT PROCESS .......................... .110
DIAGNOSIS PROCEDURE FOR SUNLOAD
SENSOR ........................................................... .110

ATC-30
AIR CONDITIONER CONTROL
Revision: 2005 July 2005 FX
AIR CONDITIONER CONTROLPFP:27500
Description of Air Conditioner LAN Control SystemAJS0014A
The LAN (Local Area Network) system consists of unified meter and A/C amp., mode door motor, air mix door
motor and intake door motor.
A configuration of these components is shown in the diagram below.
System ConstructionAJS0014B
A small network is constructed between the unified meter and A/C amp., air mix door motor, mode door motor
and intake door motor. The unified meter and A/C amp. and motors are connected by data transmission lines
and motor power supply lines. The LAN network is built through the ground circuits of each door motor.
Addresses, motor opening angle signals, motor stop signals and error checking messages are all transmitted
through the data transmission lines connecting the unified meter and A/C amp. and each door motor.
The following functions are contained in LCUs built into the air mix door motor, the mode door motor and the
intake door motor.

Address

Motor opening angle signals

Data transmission

Motor stop and drive decision

Opening angle sensor (PBR function)

Comparison

Decision (Unified meter and A/C amp. indicated value and motor opening angle comparison)
OPERATION
The unified meter and A/C amp. receives data from each of the sensors. The unified meter and A/C amp.
sends mode door, air mix door and intake door opening angle data to the mode door motor LCU, air mix door
motor LCU and intake door motor LCU.
The mode door motor, air mix door motor and intake door motor read their respective signals according to the
address signal. Opening angle indication signals received from the unified meter and A/C amp. and each of
the motor position sensors is compared by the LCUs in each motor with the existing decision and opening
angles. Subsequently, HOT/COLD, DEF/VENT and FRESH/RECIRCULATION operation is selected. The new
selection data is returned to the unified meter and A/C amp.
SJIA0262E
RJIA1747E

ATC-46
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
Wiring Diagram —A/C—AJS0014N
TJWM0151E

AV-1
AUDIO VISUAL, NAVIGATION & TELEPHONE SYS- TEM
K ELECTRICAL
CONTENTS
C
D E
F
G H
I
J
L
M
SECTION AV
A
B
AV
Revision: 2005 July 2005 FX
AUDIO VISUAL, NAVIGATION & TELEPHONE SYSTEM
PRECAUTIONS .......................................................... 5
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 5
PREPARATION ...................................................... ..... 6
Commercial Service Tools ................................... ..... 6
AUDIO .................................................................... ..... 7
Component Parts and Harness Connector Location ..... 7
System Description ............................................. ..... 8
BASE SYSTEM ................................................ ..... 8
BOSE SYSTEM ............................................... ..... 8
SPEED SENSITIVE VOLUME SYSTEM ......... ..... 9
Schematic - Base System - ................................. ... 10
Wiring Diagram - AUDIO - / Base System .......... .... 11
Schematic - BOSE System - With Navigation Sys-
tem ...................................................................... ... 16
Wiring Diagram – AUDIO – / BOSE System With
Navigation System .............................................. ... 17
Schematic - BOSE System - Without Navigation
System ................................................................ ... 25
Wiring Diagram – AUDIO – / BOSE System Without
Navigation System .............................................. ... 26
Terminals and Reference Value for Audio Unit .... ... 33
Terminals and Reference Value for BOSE Speaker
Amp. .................................................................... ... 34
Terminals and Reference Value for A/C and AV
Switch .................................................................. ... 36
Terminals and Reference Value for Woofer ......... ... 37
A/C and AV Switch Self-Diagnosis Function ....... ... 37
STARTING THE SELF-DIAGNOSIS MODE .... ... 37
EXITING THE SELF-DIAGNOSIS MODE ........ ... 37
DIAGNOSIS FUNCTION .................................. ... 37
Trouble Diagnosis ............................................... ... 38
MALFUNCTION WITH RADIO, TAPE AND CD ... 38
FOR RADIO ONLY ........................................... ... 39
FOR CASSETTE PLAYER ONLY .................... ... 39
FOR CD ONLY ................................................. ... 39
Noise Inspection .................................................. ... 40
TYPE OF NOISE AND POSSIBLE CAUSE ..... ... 40
Power Supply Circuit Inspection ......................... ... 41 Audio Steering Wheel Switch Inspection .............
... 42
A/C and AV Switch Inspection ............................. ... 44
BOSE Speaker Amp. Inspection ......................... ... 44
Vehicle Speed Signal Inspection ......................... ... 45
Locking CD Auto-Changer Mechanism ............... ... 46
DAMPER LOCK PROCEDURE ....................... ... 46
Removal and Installation of Audio Unit ................ ... 47
REMOVAL ........................................................ ... 47
INSTALLATION ................................................ ... 47
Disassembly and Assembly for Audio Unit .......... ... 47
DISASSEMBLY ................................................ ... 47
ASSEMBLY ...................................................... ... 47
Removal and Installation for A/C and AV Switch . ... 48
REMOVAL ........................................................ ... 48
INSTALLATION ................................................ ... 48
Removal and Installation for Front Door Speaker ... 48
REMOVAL ........................................................ ... 48
INSTALLATION ................................................ ... 48
Removal and Installation for Rear Door Speaker ... 49 REMOVAL ........................................................ ... 49
INSTALLATION ................................................ ... 49
Removal and Installation for Instrument Speaker ... 49 REMOVAL ........................................................ ... 49
INSTALLATION ................................................ ... 49
Removal and Installation for Tweeter .................. ... 49
REMOVAL ........................................................ ... 49
INSTALLATION ................................................ ... 49
Removal and Installation for Woofer (BOSE Sys-
tem) ..................................................................... ... 50
REMOVAL ........................................................ ... 50
INSTALLATION ................................................ ... 50
Removal and Installation for BOSE Speaker Amp. ... 50
REMOVAL ........................................................ ... 50
INSTALLATION ................................................ ... 50
AUDIO ANTENNA ................................................. ... 51
System Description .............................................. ... 51
Wiring Diagram — M/ANT — .............................. ... 52
Terminals and Reference Value for Audio Unit .... ... 53
Antenna Amp. Inspection .................................... ... 53
Location of Antenna ............................................. ... 54