2005 INFINITI FX35 key

GW-44
POWER WINDOW SYSTEM
Revision: 2005 July 2005 FX
Anti-pinch system does not operate normally (rear LH or RH) 1. Door window sliding part malfunction

A foreign material adheres to window glass or
glass run rubber.

Glass run rubber wear or deformation.

Sash is tilted too much, or no enough. —
2. Limit switch adjusting GW-78
3. Limit switch circuit check (rear LH or RH)GW-59
4. Encoder circuit check (rear LH or RH)GW-65
Power window retained power operation does not operate
properly 1. Check the retained power operation mode set-
ting. GW-41
2. Door switch check
GW-67
3. Replace BCM.BCS-16
Does not operate by key cylinder switch 1. Door key cylinder switch check
GW-692. Replace power window main switch —
Power window lock switch does not function Power window lock switch check GW-73
Auto operation does not operate but manual operate normally
(driver side) 1. Encoder circuit check (driver side)
GW-61
2. Replace power window main switch —
Auto operation does not operate but manual operate normally
(passenger side) 1. Encoder circuit check (passenger side)
GW-63
2. Replace front power window switch (passen-
ger side) —
Auto operation does not operate but manual operate normally
(rear LH or RH) 1. Encoder circuit check (rear LH or RH)
GW-65
2. Replace rear power window switch (LH or RH) —
Symptom Repair order Refer to page

POWER WINDOW SYSTEM GW-69
C
D E
F
G H
J
K L
M A
B
GW
Revision: 2005 July 2005 FX
Front Door Key Cylinder Switch Check AIS004QU
1. CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
With CONSULT-II
Check (“KEY CYL LK-SW”, “KEY CYL UN-SW”) in “DATA MONITOR” mode for “POWER DOOR ROCK SYS-
TEM” with CONSULT-II. Refer to BL-38, "
Data Monitor"
Without CONSULT-II
1. Turn ignition switch OFF.
2. Check voltage between power window main switch connector and ground.
OK or NG
OK >> Further inspection is necessary. Refer to symptom chart.
NG >> GO TO 2.
2. CHECK HARNESS CONTINUITY
1. Disconnect power window main switch and front door key lock assembly (driver side) connector.
2. Check continuity between power window main switch connector D6 terminals 4, 6 and front door lock assembly (driver side) con-
nector D10 terminals 1, 6.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
Monitor item Condition
KEY CYL LK-SW Lock : ON
Neutral / Unlock : OFF
KEY CYL UN-SW Unlock : ON
Neutral / Lock : OFF
PIIA6285E
Connector Terminals (Wire color)
Key position Voltage [V]
(Approx.)
(+) (–)
D6 4 (P)
Ground Lock 0
Neutral / Unlock 5
6 (OR) Unlock 0
Neutral / Lock 5
PIIB3971E
4 (P) – 1 (P) : Continuity should exist.
6 (OR) – 6 (OR) : Continuity should exist.
PIIA4212E

GW-70
POWER WINDOW SYSTEM
Revision: 2005 July 2005 FX
3. CHECK DOOR KEY CYLINDER SWITCH GROUND
Check continuity between front door lock assembly (driver side) con-
nector D10 terminal 5 and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
4. CHECK DOOR KEY CYLINDER SWITCH
Check continuity between door lock assembly terminals 1, 6 and 5.
OK or NG
OK >> Further inspection is necessary. Refer to symptom chart.
NG >> Replace front door key cylinder (driver side) switch. 5 (B) – Ground : Continuity should exist.
PIIA4213E
Terminals Key position Continuity
1 5 Lock Yes
Neutral / Unlock No
6 Unlock Yes
Neutral / Lock No
PIIA4214E

POWER WINDOW SYSTEM GW-71
C
D E
F
G H
J
K L
M A
B
GW
Revision: 2005 July 2005 FX
Power Window Serial Link Check (Passenger Side)AIS004QV
1. CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
With CONSULT-II
Check (“CDL LOCK SW ”, “CDL UNLOCK SW”) in DATA MONITOR mode for “REMOTE KEYLESS ENTRY
SYSTEM” with CONSULT-II. Refer to BL-38, "
Data Monitor" .
Without CONSULT-II
1. Remove key from ignition switch, and the door of driver side and passenger side is closed.
2. Check signal between BCM connector and ground with oscilloscope when door lock and unlock switch (driver side and passenger side) is turned “LOCK” or “UNLOCK”.
3. Make sure signals which are shown in the figure below can be detected during 10 second just after door lock and unlock switch (driver side and passenger side) is turned “LOCK” or “UNLOCK”.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
2. CHECK BCM OUTPUT SIGNAL
Check (“POWER WINDOW DOWN”) in “ACTIVE TEST” mode for “REMOTE KEYLESS ENTRY SYSTEM”
with CONSULT-II. Refer to BL-67, "
Active Test"
OK or NG
OK >> Further inspection is necessary. Refer to symptom
chart.
NG >> Replace BCM.
Monitor item Condition
CDL LOCK SW LOCK : ON
UNLOCK : OFF
CDL UNLOCK SW LOCK : OFF
UNLOCK : ON
PIIA7068E
Connector Terminals (Wire color)
Signal
(Reference value)
(+) (–)
M3 22 (OR) Ground
PIIA6290EPIIA1297E
When “ACTIVE TEST” is performed, is the window of
driver side and passenger side lowered.
PIIA3080E

IDX-5
A
C
D E
F
G H
I
J
K L
B
IDX
ALPHABETICAL INDEX
Hazard warning lamp ..........................................
LT-91
Headlamp aiming control .................................... LT-75
Headlamp leveler - See Headlamp aiming control .......
LT-75
Headlining - See Roof trim .................................. EI-41
Heated oxygen sensor 1 (bank 1) .... EC-935, EC-944,
EC-956
, EC-1174, EC-1180
Heated oxygen sensor 1 (bank 2) .... EC-935, EC-944,
EC-956
, EC-1174, EC-1180
Heated oxygen sensor 1 heater (bank 1) ........ EC-877
Heated oxygen sensor 1 heater (bank 2) ........ EC-877
Heated oxygen sensor 2 (bank 1) .... EC-228, EC-237,
EC-442
, EC-453, EC-966, EC-975, EC-1187, EC-1198
Heated oxygen sensor 2 (bank 2) .... EC-228, EC-237,
EC-442
, EC-453, EC-966, EC-975, EC-1187, EC-1198
Heated oxygen sensor 2 heater (bank 1) ....... EC-178,
EC-885
Heated oxygen sensor 2 heater (bank 2) ....... EC-178,
EC-885
Heated seat ....................................................... SE-97
Heater and cooling unit (Heater core) ........... ATC-126
HFC134a (R134a) system precaution ............... ATC-6
HFC134a (R134a) system service procedure ATC-138
HFC134a (R134a) system service tools .......... ATC-18
HFC134a system service equipment precaution ..........
ATC-13
High and low reverse clutch solenoid valve .... AT-162,
AT-164
Hood ................................................................... BL-13
Horn ................................................................. WW-59
HORN - Wiring diagram ................................... WW-59
HSEAT - Wiring diagram ................................... SE-98
I
IATS - Wiring diagram ....................... EC-205
, EC-911
ICC - Wiring diagram ....................................... ACS-20
ICC/BS - Wiring diagram ................. EC-590, EC-1264
ICC/SW - Wiring diagram ................ EC-576, EC-1249
ICCBOF - Wiring diagram ................ EC-681, EC-1371
Idle air volume learning ....................... EC-97, EC-787
Idle mixture ratio .............................................. EC-775
Idle speed .......................................... EC-769, EC-774
Idle speed control (ISC) .... EC-393, EC-395, EC-1125,
EC-1127
Ignition coil ....................................... EC-648, EC-1339
Ignition coil(VK45DE) ...................................... EM-189
Ignition coil(VQ35DE) ........................................ EM-42
Ignition control system ..................... EC-648, EC-1339
Ignition key hole illumination ............................. LT-155
Ignition timing .................................... EC-769, EC-774
IGNSYS - Wiring diagram ................ EC-649, EC-1340
Illumination control ............................................ LT-202
In vehicle sensor ........................... ATC-107, ATC-118
INF/D - Wring diagram ....................................... AV-63
INJECT - Wiring diagram ................. EC-662, EC-1352
Injector ............................................. EC-661, EC-1351
Input clutch solenoid valve ................. AT-150, AT-152
Instrument panel .................................................. IP-10
Intake air temperature sensor ........... EC-203, EC-223,
EC-909
, EC-930
Intake door control linkage adjustment ............ ATC-78
Intake door motor ............................ ATC-76, ATC-124
Intake manifold collector(VQ35DE) .................. EM-19
Intake manifold(VK45DE) ............................... EM-178
Intake manifold(VQ35DE) ................................. EM-24
Intake sensor ................................ ATC-113, ATC-120
Intake valve timing control (Bank 1) ... EC-174, EC-865
Intake valve timing control (Bank 2) ... EC-174, EC-865
Intake valve timing control position sensor (Bank 1) ....
EC-1166
Intake valve timing control position sensor (Bank 2) ....
EC-1166
Intake valve timing control solenoid valve (Bank 1) ......
EC-417
, EC-1141
Intake valve timing control solenoid valve (Bank 2) ......
EC-417
, EC-1141
Integrated homelink transmitter ....................... BL-235
Intelligent cruise control (ICC) system .............. ACS-6
Interior ................................................................. EI-36
Interior lamp ...................................................... LT-159
IPDM (Intelligent power distribution module engine
room) ................................................................. PG-18
IVCB1 - Wiring diagram ................... EC-418, EC-1142
IVCB2 - Wiring diagram ................... EC-420, EC-1144
IVCSB1 - Wiring diagram ............................... EC-1167
IVCSB2 - Wiring diagram ............................... EC-1169
IVIS (Infiniti vehicle immobilizer system) precautions ...
GI-3
IVTB1 - Wiring diagram ................................... EC-868
IVTB2 - Wiring diagram ................................... EC-870
K
Knock sensor (KS) ........................... EC-295
, EC-1031
KS - Wiring diagram ......................... EC-296, EC-1032
L
LAN system circuit ........................................... ATC-66
Lane Departure Warning System ....................... DI-82
Laser beam aiming adjustment ....................... ACS-12
Latch (lower anchors and tether for children) system ...
SB-9
LDW .................................................................... DI-82
LDW - Wiring Diagram ........................................ DI-95
Line pressure solenoid valve ........................... AT-129
Line pressure test (A/T) ..................................... AT-54
Liquid gasket application ......................... EM-6, LU-21
Liquid gasket application(VQ35DE) ........... LU-3, CO-3
Location of electrical units ................................. PG-70
Low coast brake solenoid valve ......... AT-166, AT-168
Low tire pressure warning system ...................... WT-7
Lubricant (R134a) A/C ..................................... ATC-27
Lubrication circuit (engine)(VK45DE) ................ LU-23
Lubrication circuit (engine)(VQ35DE) .................. LU-5
Lubrication oil A/C .......................................... ATC-162

LAN-1
LAN SYSTEM
K ELECTRICAL
CONTENTS
C
D E
F
G H
I
J
L
M
SECTION LAN
A
B
LAN
Revision: 2005 July 2005 FX
LAN SYSTEM
CAN
PRECAUTIONS .......................................................... 5
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 5
Precautions When Using CONSULT-II ................ ..... 5
CHECK POINTS FOR USING CONSULT-II .... ..... 5
Precautions For Trouble Diagnosis ..................... ..... 5
CAN SYSTEM .................................................. ..... 5
Precautions For Harness Repair ......................... ..... 6
CAN SYSTEM .................................................. ..... 6
TROUBLE DIAGNOSES WORK FLOW ............... ..... 7
When Displaying CAN Communication System
Errors .................................................................. ..... 7
WHEN A MALFUNCTION IS DETECTED BY
CAN COMMUNICATION SYSTEM .................. ..... 7
WHEN A MALFUNCTION IS DETECTED
EXCEPT CAN COMMUNICATION SYSTEM ... ..... 7
TROUBLE DIAGNOSIS FLOW CHART .......... ..... 8
Diagnosis Procedure ........................................... ..... 9
SELECTING CAN SYSTEM TYPE (HOW TO
USE SPECIFICATION TABLE) ........................ ..... 9
ACQUISITION OF DATA BY CONSULT-II ....... ... 10
HOW TO USE CHECK SHEET TABLE ........... .... 11
CAN Diagnostic Support Monitor ........................ ... 18
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR ECM ............................ ... 18
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR TCM ............................ ... 19
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR DISPLAY CONTROL
UNIT ................................................................. ... 20
DESCRIPTION OF “CAN DIAG MNTR” SCREEN
FOR DISPLAY UNIT ........................................ ... 21
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR AWD CONTROL UNIT ... 22
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR ICC UNIT .................... ... 23
DESCRIPTION OF “CAN DIAG SUPPORT MNTR” SCREEN FOR INTELLIGENT KEY UNIT
... 24
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR BCM ............................ ... 25
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR LDW CAMERA UNIT ... ... 26
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR UNIFIED METER AND A/
C AMP. .............................................................. ... 27
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR ABS ACTUATOR AND
ELECTRIC UNIT (CONTROL UNIT) ................ ... 28
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR DRIVER SEAT CON-
TROL UNIT ...................................................... ... 28
DESCRIPTION OF “CAN DIAG SUPPORT
MNTR” SCREEN FOR IPDM E/R .................... ... 29
CAN COMMUNICATION ........................................ ... 30
System Description .............................................. ... 30
CAN Communication Unit .................................... ... 30
TYPE 1/TYPE 2/TYPE 9 .................................. ... 30
TYPE 3/TYPE 4 ................................................ ... 34
TYPE 5/TYPE 6/TYPE 10 ................................ ... 38
TYPE 7/TYPE 8 ................................................ ... 42
CAN SYSTEM (TYPE 1) ........................................ ... 47
Component Parts and Harness Connector Location ... 47
Schematic ............................................................ ... 48
Wiring Diagram - CAN - ....................................... ... 49
Check Sheet ........................................................ ... 52
CHECK SHEET RESULTS (EXAMPLE) .......... ... 54
Inspection Between TCM and Data Link Connector
Circuit .................................................................. ... 70
Inspection Between Data Link Connector and Uni-
fied Meter and A/C Amp. Circuit .......................... ... 71
Inspection Between Unified Meter and A/C Amp.
and ABS Actuator and Electric Unit (Control Unit)
Circuit .................................................................. ... 71
Inspection Between ABS Actuator and Electric Unit
(Control Unit) and Driver Seat Control Unit Circuit ... 72
ECM Circuit Inspection ........................................ ... 73
TCM Circuit Inspection ........................................ ... 73

LAN-2Revision: 2005 July 2005 FX
Display Unit Circuit Inspection .............................
... 74
Data Link Connector Circuit Inspection ............... ... 74
BCM Circuit Inspection ........................................ ... 75
Steering Angle Sensor Circuit Inspection ............ ... 75
Unified Meter and A/C Amp. Circuit Inspection ... ... 76
ABS Actuator and Electric Unit (Control Unit) Circuit
Inspection ............................................................ ... 76
Driver Seat Control Unit Circuit Inspection .......... ... 77
IPDM E/R Circuit Inspection ................................ ... 78
CAN Communication Circuit Inspection ............... ... 78
IPDM E/R Ignition Relay Circuit Inspection ......... ... 84
CAN SYSTEM (TYPE 2) ........................................ ... 85
Component Parts and Harness Connector Location ... 85
Schematic ............................................................ ... 86
Wiring Diagram - CAN - ....................................... ... 87
Check Sheet ........................................................ ... 90
CHECK SHEET RESULTS (EXAMPLE) .......... ... 93
Inspection Between TCM and Data Link Connector
Circuit .................................................................. .110
Inspection Between Data Link Connector and Uni-
fied Meter and A/C Amp. Circuit .......................... ..111
Inspection Between Unified Meter and A/C Amp.
and ABS Actuator and Electric Unit (Control Unit)
Circuit .................................................................. ..111
Inspection Between ABS Actuator and Electric Unit
(Control Unit) and Driver Seat Control Unit Circuit .112
ECM Circuit Inspection ........................................ .113
TCM Circuit Inspection ........................................ .113
Display Unit Circuit Inspection ............................. .114
Data Link Connector Circuit Inspection ............... .114
BCM Circuit Inspection ........................................ .115
Steering Angle Sensor Circuit Inspection ............ .115
LDW Camera Unit Circuit Inspection ................... .116
Unified Meter and A/C Amp. Circuit Inspection ... .117
ABS Actuator and Electric Unit (Control Unit) Circuit
Inspection ............................................................ .117
Driver Seat Control Unit Circuit Inspection .......... .118
IPDM E/R Circuit Inspection ................................ .118
CAN Communication Circuit Inspection ............... .119
IPDM E/R Ignition Relay Circuit Inspection ......... .125
CAN SYSTEM (TYPE 3) ........................................ .126
Component Parts and Harness Connector Location .126
Schematic ............................................................ .127
Wiring Diagram - CAN - ....................................... .128
Check Sheet ........................................................ .131
CHECK SHEET RESULTS (EXAMPLE) .......... .135
Inspection Between TCM and Data Link Connector
Circuit .................................................................. .154
Inspection Between Data Link Connector and Uni-
fied Meter and A/C Amp. Circuit .......................... .155
Inspection Between Unified Meter and A/C Amp.
and ABS Actuator and Electric Unit (Control Unit)
Circuit .................................................................. .155
Inspection Between ABS Actuator and Electric Unit
(Control Unit) and Driver Seat Control Unit Circuit .156
ECM Circuit Inspection ........................................ .157
TCM Circuit Inspection ........................................ .157
Display Control Unit Circuit Inspection ................ .158
ICC Unit Circuit Inspection .................................. .158 Intelligent Key Unit Circuit Inspection ..................
.159
Data Link Connector Circuit Inspection ................ .159
BCM Circuit Inspection ........................................ .160
Steering Angle Sensor Circuit Inspection ............. .160
Unified Meter and A/C Amp. Circuit Inspection .... .161
ICC Sensor Circuit Inspection .............................. .161
ABS Actuator and Electric Unit (Control Unit) Circuit
Inspection ............................................................. .162
Driver Seat Control Unit Circuit Inspection .......... .162
IPDM E/R Circuit Inspection ................................ .163
CAN Communication Circuit Inspection ............... .164
IPDM E/R Ignition Relay Circuit Inspection .......... .170
CAN SYSTEM (TYPE 4) ......................................... .171
Component Parts and Harness Connector Location .171
Schematic ............................................................ .172
Wiring Diagram - CAN - ....................................... .173
Check Sheet ........................................................ .176
CHECK SHEET RESULTS (EXAMPLE) ........... .180
Inspection Between TCM and Data Link Connector
Circuit ................................................................... .200
Inspection Between Data Link Connector and Uni-
fied Meter and A/C Amp. Circuit .......................... .201
Inspection Between Unified Meter and A/C Amp.
and ABS Actuator and Electric Unit (Control Unit)
Circuit ................................................................... .201
Inspection Between ABS Actuator and Electric Unit
(Control Unit) and Driver Seat Control Unit Circuit .202
ECM Circuit Inspection ........................................ .203
TCM Circuit Inspection ......................................... .203
Display Control Unit Circuit Inspection ................. .204
ICC Unit Circuit Inspection ................................... .204
Intelligent Key Unit Circuit Inspection .................. .205
Data Link Connector Circuit Inspection ................ .205
BCM Circuit Inspection ........................................ .206
Steering Angle Sensor Circuit Inspection ............. .206
LDW Camera Unit Circuit Inspection ................... .207
Unified Meter and A/C Amp. Circuit Inspection .... .208
ICC Sensor Circuit Inspection .............................. .208
ABS Actuator and Electric Unit (Control Unit) Circuit
Inspection ............................................................. .209
Driver Seat Control Unit Circuit Inspection .......... .209
IPDM E/R Circuit Inspection ................................ .210
CAN Communication Circuit Inspection ............... .211
IPDM E/R Ignition Relay Circuit Inspection .......... .218
CAN SYSTEM (TYPE 5) ......................................... .219
Component Parts and Harness Connector Location .219
Schematic ............................................................ .220
Wiring Diagram - CAN - ....................................... .221
Check Sheet ........................................................ .224
CHECK SHEET RESULTS (EXAMPLE) ........... .227
Inspection Between TCM and Data Link Connector
Circuit ................................................................... .244
Inspection Between Data Link Connector and Uni-
fied Meter and A/C Amp. Circuit .......................... .245
Inspection Between Unified Meter and A/C Amp.
and ABS Actuator and Electric Unit (Control Unit)
Circuit ................................................................... .245
Inspection Between ABS Actuator and Electric Unit
(Control Unit) and Driver Seat Control Unit Circuit .246

LAN-3
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2005 July 2005 FX
ECM Circuit Inspection ........................................
. 247
TCM Circuit Inspection ........................................ . 247
Display Unit Circuit Inspection ............................ . 248
AWD Control Unit Circuit Inspection ................... . 248
Data Link Connector Circuit Inspection ............... . 249
BCM Circuit Inspection ........................................ . 249
Steering Angle Sensor Circuit Inspection ............ . 250
Unified Meter and A/C Amp. Circuit Inspection ... . 250
ABS Actuator and Electric Unit (Control Unit) Circuit
Inspection ............................................................ . 251
Driver Seat Control Unit Circuit Inspection .......... . 251
IPDM E/R Circuit Inspection ................................ . 252
CAN Communication Circuit Inspection .............. . 253
IPDM E/R Ignition Relay Circuit Inspection ......... . 259
CAN SYSTEM (TYPE 6) ........................................ . 260
Component Parts and Harness Connector Location . 260
Schematic ........................................................... . 261
Wiring Diagram - CAN - ...................................... . 262
Check Sheet ........................................................ . 265
CHECK SHEET RESULTS (EXAMPLE) .......... . 269
Inspection Between TCM and Data Link Connector
Circuit .................................................................. . 287
Inspection Between Data Link Connector and Uni-
fied Meter and A/C Amp. Circuit .......................... . 288
Inspection Between Unified Meter and A/C Amp.
and ABS Actuator and Electric Unit (Control Unit)
Circuit .................................................................. . 288
Inspection Between ABS Actuator and Electric Unit
(Control Unit) and Driver Seat Control Unit Circuit . 289
ECM Circuit Inspection ........................................ . 290
TCM Circuit Inspection ........................................ . 290
Display Unit Circuit Inspection ............................ . 291
AWD Control Unit Circuit Inspection ................... . 291
Data Link Connector Circuit Inspection ............... . 292
BCM Circuit Inspection ........................................ . 292
Steering Angle Sensor Circuit Inspection ............ . 293
LDW Camera Unit Circuit Inspection .................. . 293
Unified Meter and A/C Amp. Circuit Inspection ... . 294
ABS Actuator and Electric Unit (Control Unit) Circuit
Inspection ............................................................ . 295
Driver Seat Control Unit Circuit Inspection .......... . 295
IPDM E/R Circuit Inspection ................................ . 296
CAN Communication Circuit Inspection .............. . 297
IPDM E/R Ignition Relay Circuit Inspection ......... . 303
CAN SYSTEM (TYPE 7) ........................................ . 304
Component Parts and Harness Connector Location . 304
Schematic ........................................................... . 305
Wiring Diagram - CAN - ...................................... . 306
Check Sheet ........................................................ . 309
CHECK SHEET RESULTS (EXAMPLE) .......... . 313
Inspection Between TCM and Data Link Connector
Circuit .................................................................. . 333
Inspection Between Data Link Connector and Uni-
fied Meter and A/C Amp. Circuit .......................... . 334
Inspection Between Unified Meter and A/C Amp.
and ABS Actuator and Electric Unit (Control Unit)
Circuit .................................................................. . 334
Inspection Between ABS Actuator and Electric Unit
(Control Unit) and Driver Seat Control Unit Circuit . 335 ECM Circuit Inspection ........................................
.336
TCM Circuit Inspection ........................................ .336
Display Control Unit Circuit Inspection ................ .337
AWD Control Unit Circuit Inspection .................... .337
ICC Unit Circuit Inspection .................................. .338
Intelligent Key Unit Circuit Inspection .................. .338
Data Link Connector Circuit Inspection ............... .339
BCM Circuit Inspection ........................................ .339
Steering Angle Sensor Circuit Inspection ............ .340
Unified Meter and A/C Amp. Circuit Inspection ... .340
ICC Sensor Circuit Inspection ............................. .341
ABS Actuator and Electric Unit (Control Unit) Circuit
Inspection ............................................................ .341
Driver Seat Control Unit Circuit Inspection .......... .342
IPDM E/R Circuit Inspection ................................ .343
CAN Communication Circuit Inspection .............. .344
IPDM E/R Ignition Relay Circuit Inspection ......... .350
CAN SYSTEM (TYPE 8) ........................................ .351
Component Parts and Harness Connector Location .351
Schematic ............................................................ .352
Wiring Diagram - CAN - ....................................... .353
Check Sheet ........................................................ .356
CHECK SHEET RESULTS (EXAMPLE) .......... .360
Inspection Between TCM and Data Link Connector
Circuit .................................................................. .381
Inspection Between Data Link Connector and Uni-
fied Meter and A/C Amp. Circuit .......................... .382
Inspection Between Unified Meter and A/C Amp.
and ABS Actuator and Electric Unit (Control Unit)
Circuit .................................................................. .382
Inspection Between ABS Actuator and Electric Unit
(Control Unit) and Driver Seat Control Unit Circuit .383
ECM Circuit Inspection ........................................ .384
TCM Circuit Inspection ........................................ .384
Display Control Unit Circuit Inspection ................ .385
AWD Control Unit Circuit Inspection .................... .385
ICC Unit Circuit Inspection .................................. .386
Intelligent Key Unit Circuit Inspection .................. .386
Data Link Connector Circuit Inspection ............... .387
BCM Circuit Inspection ........................................ .387
Steering Angle Sensor Circuit Inspection ............ .388
LDW Camera Unit Circuit Inspection ................... .388
Unified Meter and A/C Amp. Circuit Inspection ... .389
ICC Sensor Circuit Inspection ............................. .390
ABS Actuator and Electric Unit (Control Unit) Circuit
Inspection ............................................................ .390
Driver Seat Control Unit Circuit Inspection .......... .391
IPDM E/R Circuit Inspection ................................ .391
CAN Communication Circuit Inspection .............. .392
IPDM E/R Ignition Relay Circuit Inspection ......... .399
CAN SYSTEM (TYPE 9) ........................................ .400
Component Parts and Harness Connector Location .400
Schematic ............................................................ .401
Wiring Diagram - CAN - ....................................... .402
Check Sheet ........................................................ .405
CHECK SHEET RESULTS (EXAMPLE) .......... .407
Inspection Between TCM and Data Link Connector
Circuit .................................................................. .421
Inspection Between Data Link Connector and Uni-