2005 INFINITI FX35 lock

NAVIGATION SYSTEM AV-95
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
2. Push “Enter” switch.

The indicator light alternately turns on and off each time the “Enter” switch is pressed.
Keyless Remote Response -Horn
1. Select “Keyless Remote Response-Horn”.
2. Push “Enter” switch.

The indicator light alternately turns on and off each time the “Enter” switch is pressed.
Keyless Remote Response -Lights
1. Select “Keyless Remote Response-Light”.
2. Push “Enter” switch.
Auto Re-Lock Time
1. Select “Auto Re-Lock Time”.
2. Move the joystick and push “Enter” switch to adjust the time.
Sensitivity of Automatic Headlights
1. Select “Sensitivity of Automatic Headlights”.
2. Move the joystick to left (lower) or right (higher) and push “Enter” switch.
Automatic Headlights Off Delay
1. Select “Automatic Headlights Off Delay”.
2. Move the joystick left or right to adjust the timer and push “Enter” switch.
Speed Dependent Wiper
1. Select “Speed Dependent Wiper”.
2. Push “Enter” switch.

The indicator light alternately turns on and off each time the “Enter” switch is pressed.
Intelligent Key Lock Response-Sound
1. Select “Intelligent Key Lock Response-Sound”.
2. Push “Enter” switch to change the sound pattern.
Intelligent Key Unlock Response-Beep Sound
1. Select “Intelligent Key Unlock Response-Sound”.
2. Push “Enter” switch to change the sound pattern.
Intelligent Key Lock/Unlock Function
1. Select “Intelligent Key Lock/Unlock”.
2. Push “Enter” switch.

The indicator light alternately turns on and off each time the “Enter” switch is pressed.
Return All Settings to Default
1. Select “Return All Settings to Default”.
2. Push “Enter” switch.

The indicator light alternately turns on and off each time the “Enter” switch is pressed.

NAVIGATION SYSTEM AV-103
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
TIRE PRESSURE

Pressure indication in psi on the screen indicates that the
pressure is being measured. After a few driving trips, the pres-
sures for all four tires will be displayed.

The order of tire pressure figures displayed on the screen does
not correspond with the actual order of the tire position.

Tire pressure rises and falls depending on the heat caused by
the vehicle's traveling condition and the temperature.

FLAT TIRE–very low tire air pressure.
NOTE:

In a case of FLAT TIRE pressure, interrupt screen is not shown
on the display.

On the screen of TIRE PRESSURE, “FLAT TIRE”, “Check”, “All tire” is displayed.
WARNING INDICATIONS
Warning signal (door switch signal) is received from BCM through
CAN communication line.
SKIA5994E
SKIA5995E
Warning
indicators Warning lamps in
instrument panel Warning detection and cancel conditions
Cases of
malfunction
DOOR OPEN Door Detection condition
Vehicle is running [approx. 5km/h (3 MPH) or faster]
and door ajar of any of the doors is detected. Door is open.
Cancel condition Vehicle is stopped and all the doors lock.

NAVIGATION SYSTEM AV-129
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
Self-Diagnosis Mode (DCU)AKS007J0
OPERATION PROCEDURE
1. Start the engine.
2. Turn the audio system off.
3. While pressing the “MUTE/ II ” button, turn the volume control
dial clockwise or counterclockwise for 30 clicks or more. (When
the self-diagnosis mode is started, a short beep will be heard.)

Shifting from current screen to previous screen is performed
by pressing “PREV” button.
4. The initial trouble diagnosis screen will be shown, and items “Self-Diagnosis (DCU)”,“Self-Diagnosis (NAVI)”, “Confirmation/
Adjustment” and “CAN DIAG SUPPORT MONITOR” will
become selective.
5. Perform self-diagnosis by selecting the “Self-diagnosis (DCU)”.

Self-diagnosis subdivision screen will be shown and the oper-
ation enters the self-diagnosis mode.

A bar graph shown below the self-diagnosis subdivision
screen indicates progress of the diagnosis.
6. When the self-diagnosis completes, optional part confirmation screen will be shown.

When connection of an optional part is judged error, a screen
to check if the optional part is actually fitted on the vehicle or
not will be shown. When fitted, select the switch of the part on
the screen and press “End”. Then the “SELF DIAGNOSIS”
screen will be shown.

When the optional part is connected normally, the switch for
the part will not appear on the screen.
PKIB4131E
SKIA4207E
SKIA4208E
SKIA4209E

NAVIGATION SYSTEM AV-131
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
Self-Diagnosis Codes
Self-Diagnosis Mode (NAVI)AKS007J1
OPERATION PROCEDURE
1. Start the engine.
2. Turn the audio system off.
3. While pressing the “MUTE/ II ” button, turn the volume control
dial clockwise or counterclockwise for 30 clicks or more. (When
the self-diagnosis mode is started, a short beep will be heard.)

Shifting from current screen to previous screen is performed
by pressing “PREV” button.
4. The initial trouble diagnosis screen will be shown, and items “Self-Diagnosis (DCU)”, “Self-Diagnosis (NAVI)”, “Confirmation/
Adjustment” and “CAN DIAG SUPPORT MONITOR” will
become selective.
5. Perform self-diagnosis by selecting the “Self-diagnosis (NAVI)”.

Self-diagnosis subdivision screen will be shown and the oper-
ation enters the self-diagnosis mode.

A bar graph shown below the self-diagnosis subdivision
screen indicates progress of the diagnosis.
6. On the “SELF DIAGNOSIS” screen, each unit name will be col- ored according to the diagnosis result, as follows.

If several malfunctions are present in a unit, color of its switch
on the screen will be either red, yellow, or gray, determined by
the malfunction of the highest priority.
Diagnosis No. Possible cause Reference page
1 Display control unit malfunction AV-181
2 Display communication line between display control unit and display.AV-152
3 Audio unit power supply and ground circuit.
Audio communication line between display control unit and audio unit. AV-150
4 AV communication line check (between display control unit and NAVI control unit)
AV-149
PKIB4131E
SKIA4207E
SKIA4212E
Green : No malfunctioning.
Yellow : Cannot be judged by self-diagnosis results.
Red : Unit is malfunctioning.
Gray : Diagnosis has not been done.
SKIA4214E

NAVIGATION SYSTEM AV-133
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
Confirmation/Adjustment ModeAKS007J2
OPERATION PROCEDURE
1. Start the engine.
2. Turn the audio system off.
3. While pressing the “MUTE/ II ” button, turn the volume control
dial clockwise or counterclockwise for 30 clicks or more. (When
the self-diagnosis mode is started, a short beep will be heard.)

Shifting from current screen to previous screen is performed
by pressing “PREV” button.
4. The initial trouble diagnosis screen will be shown, and items “Self-Diagnosis (DCU)”,“Self-Diagnosis (NAVI)”,“Confirmation/
Adjustment” and “CAN DIAG SUPPORT MONITOR” will
become selective.
5. When “Confirmation/Adjustment” is selected on the initial trouble diagnosis screen, the operation will enter the CONFIRMATION/
ADJUSTMENT mode. In this mode, check and adjustment of
each item will become possible.
6. The initial screen will be shown, and items “Display Diagno- sis”,“Vehicle Signals”,“Auto Climate Control” and “Navigation”
will become selective.
7. Select each switch on “CONFIRMATION/ADJUSTMENT” screen to display the relevant diagnosis screen.
3 When “DVD-ROM error. Please check disc.” is shown.
1. Eject map DVD-ROM and check if it is compatible with the system.
2. Check ejected DVD-ROM for dirt, damage, and warpage.
3. If no error is found, insert a known good map DVD-ROM of the same type and perform self-diagnosis again. If same result is shown, the NAVI control unit is malfunctioning. If result is normal, the map DVD-
ROM is malfunctioning. AV-155
4
If “Error found in DVD-ROM or DVD-ROM driver in control unit. Please perform diagnosis in accordance with
service manual” is shown, carry out same inspection as diagnosis No. 3. AV-155
5 GPS antenna system
1. Visually check for a broken wire in the GPS antenna coaxial cable.
2. Disconnect GPS antenna connector, and make sure approximately 5V is supplied from the NAVI control unit. If not, the NAVI control unit is malfunctioning. If 5V is supplied, replace the GPS antenna. If the con-
nection is still malfunction after the replacement of the GPS antenna, the NAVI control unit is malfunction-
ing. AV-156
Diagnosis
No. Possible cause Reference
page
PKIB4131E
SKIA4207E
SKIA4220E

AV-138
NAVIGATION SYSTEM
Revision: 2005 July 2005 FX
NAVIGATION
1. The initial screen will be shown, and items “Display Longitude &
Latitude”,“Speed Calibration”,“Angle Adjustment” and “Initialize
Location” will become selective.
2. Select each switch on “NAVIGATION” screen to display the rele- vant diagnosis screen.
GPS ROM
malfunction
GPS RAM
malfunction Contents of ROM (or RAM) in GPS substrate are malfunctioning.

Location detection accuracy of the navigation
system will deteriorate, depending on the error
area in the memory, because GPS cannot make
correct positioning.
(Location correction using GPS is not per-
formed.)

Perform self-diagnosis.

When the NAVI control unit is judged normal by self-diagnosis,
the symptom may be intermittent, caused by strong radio inter-
ference.
GPS RTC
malfunction Clock IC in GPS substrate is malfunctioning.

Correct time may not be displayed.

After the power is turned on, the system always
takes some time until GPS positioning becomes
possible. (The GPS receiver starts positioning
without re-collecting the whole satellite informa-
tion when it judged the data stored in the
receiver is correct.)

Correct time of error occurrence may not be
stored in the ″History of Errors ″.

Perform self-diagnosis.

When the NAVI control unit is judged normal by self-diagnosis,
the symptom may be intermittent, caused by strong radio inter-
ference.
GPS antenna
disconnected Malfunctioning connection between GPS substrate in
NAVI control unit and GPS antenna.

Navigation location detection performance has
deteriorated.
(Location correction using GPS is not per-
formed.)

GPS receiving status remains gray.

Perform self-diagnosis.

When connection between NAVI control unit and GPS
antenna is judged normal by self-diagnosis, the symptom may
be intermittent, caused by impact or vibration.
Low voltage
of GPS The power voltage supplied to the GPS circuit board has
decreased.

Navigation location detection performance has
deteriorated.
(Location correction using GPS is not per-
formed.)

GPS receiving status remains gray.

Perform self-diagnosis.

When connection between NAVI control unit and GPS
antenna is judged normal by self-diagnosis, the symptom may
be intermittent, caused by impact or vibration.
DVD-ROM
Malfunction
DVD-ROM
Read error
DVD-ROM
Response
Error Malfunctioning NAVI control unit —
Dedicated map DVD-ROM is in the system, but the data cannot
be read.

The map of a particular location cannot be dis-
played.

Specific guidance information cannot be dis-
played.

Map display is slow.

Guidance information display is slow.

System has been affected by vibration.

Is map DVD-ROM damaged, warped, or dirty?
–If damaged or warped, the map DVD-ROM is malfunctioning.
–If dirty, wipe the DVD-ROM clean with a soft cloth.

Perform self-diagnosis.

When NAVI control unit is judged normal by self-diagnosis, the
symptom is judged intermittent, caused by vibration.
Error item
Possible causes
Example of symptom
Action/symptom
SKIA4576E

AV-140
NAVIGATION SYSTEM
Revision: 2005 July 2005 FX
CAN Diag Support MonitorAKS007J3
OPERATION PROCEDURE
1. Start the engine.
2. Turn the audio system off.
3. While pressing the “MUTE/ II ” button, turn the volume control
dial clockwise or counterclockwise for 30 clicks or more. (When
the self-diagnosis mode is started, a short beep will be heard.)

Shifting from current screen to previous screen is performed
by pressing “PREV” button.
4. The initial trouble diagnosis screen will be shown, and items “Self-Diagnosis (DCU)”, “Self-Diagnosis (NAVI)”, “Confirmation/
Adjustment” and “CAN DIAG SUPPORT MONITOR” will
become selective.
5. Select “CAN DIAG SUPPORT MONITOR”.
6. Display status of CAN communication.
NOTE:
Counter shows the status of CAN communication
PKIB4131E
SKIA4207E
Item Content Error counter
(Reference value)
CANCOMM OK/NG 0-50
CAN_CIRC_1 OK/UNKWN 0-50
CAN_CIRC_2 OK/UNKWN 0-50
CAN_CIRC_3 OK/UNKWN 0-50
CAN_CIRC_4 OK/UNKWN 0-50
CAN_CIRC_5 OK/UNKWN 0-50
CAN_CIRC_6 OK/UNKWN 0-50
CAN_CIRC_7 OK/UNKWN 0-50
CAN_CIRC_8 OK/UNKWN 0-50
CAN_CIRC_9 OK/UNKWN 0-50
SKIA4288E

AV-182
INFINITI MOBILE ENTERTAINMENT SYSTEM
Revision: 2005 July 2005 FX
INFINITI MOBILE ENTERTAINMENT SYSTEMPFP:28184
System DescriptionAKS007WH
Refer to Owner's Manual for mobile entertainment system operating instructions.
Power is supplied at all times

through 15A fuse (No. 32, located in the fuse and fusible link block)

to DVD player terminal 16

through DVD player terminals 31 and 32

to DVD display terminals 15 and 16.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 6, located in the fuse block (J/B)]

to DVD player terminal 15

through DVD player terminal 21

to DVD display terminal 5.
Ground is supplied

to DVD player terminal 22

through body ground B15 and B45

to DVD player terminals 19, 27

through DVD display terminals 6, 10 and 12.
When DVD player power switch is ON, power is supplied

through DVD player terminal 9

to audio unit terminal 38 and

through audio unit terminal 40

to DVD player terminal 11.
When DVD player power switch is ON, DVD sound signals are supplied

through DVD player terminals 17, 18, and 20

to DVD display terminals 1, 2 and 4.
DVD sound can be heard by the head phone.
When rear AV switch is ON, audio signals are supplied

through DVD player terminals 1, 2, 3, and 4

to audio unit terminals 37, 39, 43, and 42.
DVD sound can be heard from the speaker.
When DVD player power switch is ON, video signals are supplied

through DVD player terminals 23 and 24

to DVD display terminals 7 and 8.
When remote controller is operated, operation signals are supplied

through DVD display terminal 14

to DVD player terminal 30 and

through DVD player terminal 29

to DVD display terminal 13.