2005 CITROEN C6 AUX

Downloaded from www.Manualslib.com manuals search engine GENERAL
Vehicle identification1 - 4
General specifications: dimensions 5 - 6
General specifications: weights7
Operations to be performed before and
after a disconnection of the battery8
Towing specifications9 - 10
Lifting and supporting the vehicle11 - 15
Capacities18
Lubricants18 - 20
ENGINE
Engine specifications22
Engine suspension tightening torques: ES9A23
Tightening torques: ES9A engine24 - 28
Suspension tightening torques: DT1729 - 31
Adjustment of torque reaction rod32
Tightening torques: DT17 engines33 - 41
Cylinder head tightening42 - 43IGNITION
Sparking plugs100
CLUTCH - GEARBOX - TRANSMISSION
Speedometer101
AM6 automatic gearbox specifications
102
Procedure before operations103
Precautions: AM6 gearbox104
AM6 gearbox specifications105
Tightening torques: AM6 gearbox106 - 107
AM6 gearbox control specifications 108 - 110
Shift lock function111
Initialisation of the AM6 gearbox112 - 113
Draining-filling-topping up
the AM6 gearbox114 - 116
Oil pressure checks: AM6 gearbox117 - 119
Transmission120
CONTENTS
Auxiliary equipment drive belt45
Checking and setting the valve timing50
Exhaust line specifications68 - 72
Cooling system specifications73 - 75
Checking the oil pressure76
Valve clearances77
Drain-fill-bleed the engine cooling circuit78 - 82
INJECTION
BOSCH 7.4.7 injection system83 - 89
Prohibited operations: SIEMENS HDi
direct injection90 - 91
Safety requirements: HDi direct injection92
Checking the low pressure fuel
supply circuit 93 - 94
Turbo pressure checks95 - 97
Air supply circuit specifications98
Checking the air supply circuit99
Angl-C6-Index-2005 4/02/05 17:10 Page III

Downloaded from www.Manualslib.com manuals search engine 15
GENERAL
LIFTING AND SUPPORTING THE VEHICLE
Raising the vehicle on a lift, supported from the jacking points.
Equipment involved:
- Two-column lift.
- Auxiliary lift with blocks.
IMPERATIVE: Position the safety straps, if placing the vehicle on a lift supported from the jacking points
(risk of the vehicle overbalancing when a heavy component is removed).
Tooling required.
[1] Safety straps
Using the safety straps.
WARNING: Check the condition of the safety straps before using them, do not use worn safety straps.
WARNING: Do not use straps that show any signs of oil or grease (risk of soiling the carpets and/or
seats).
Place protections on the front seats and on the fragile parts of the vehicle.
Example:
- Two-column lift.
- Place the safety straps[1] under the arm of the lift and criss-crossing the vehicle.
E2AP02FCE5AP2DNC
Angl-C6-page001-21-2005 4/02/05 17:12 Page 15

Downloaded from www.Manualslib.com manuals search engine 45
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engine type
C6
See pages:Petrol Diesel
3.0i 24S 2,7 24V
XFV UHZ
XX
47 to 48 49
Angl-C6-page022-82-2005 4/02/05 17:19 Page 45

Downloaded from www.Manualslib.com manuals search engine 46
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engines : all types Petrol and Diesel
Tools.
Belt tension measuring instrument: 4122-T.(C.TRONIC 105.5).
WARNING: If using tool 4099-T (C.TRONIC 105).
Essential.
Before refitting the auxiliary equipment drive belt, check that:
- 1 / The roller(s) rotate freely (no play or stiffness).
- 2 / The belt is correctly engaged in the grooves of the various pulleys.
Angl-C6-page022-82-2005 4/02/05 17:19 Page 46

Downloaded from www.Manualslib.com manuals search engine 47
ENGINE
B1BP27EC
AUXILIARY EQUIPMENT DRIVE BELT
Engine: ES9A
Tools.
[1] Ratchet spanner S.171 FACOM (1/2 square): S 171
[2]Reduction box S.230 FACOM (1/2 - 3/8): S 230
Removing.
Remove the engine cover.
Pivot the tensioner roller bracket (1)clockwise, until it locks,
using tools [1]and [2]at «a».
Remove the auxiliary equipment drive belt.
ESSENTIAL: Check that the guide rollers are turning freely
(no play and no tightness).
Refitting.
Refit the auxiliary equipment drive belt.
Respect the following order of assembly:
- The crankshaft pulley (2).
- The tensioner roller (3).
Release the tensioner roller bracket (1), by turning it anti-clockwise,
using tools [1]and [2].
ESSENTIAL: Make sure that the belt is correctly positioned in
the grooves of the various pulleys.
B1BP27FC
Angl-C6-page022-82-2005 4/02/05 17:19 Page 47

Downloaded from www.Manualslib.com manuals search engine 48
ENGINE
B1BP3BSD
AUXILIARY EQUIPMENT DRIVE BELT
Engine: ES9A
Tool.
[1] 2 mmdiameter peg: (-).0188-Q1
Removing.
Remove:
- The under-engine sound-deadening.
- The front RH wheel.
- The RH splash-shield.
- The air duct (linking the air distributor heat exchanger).
Compress the dynamic tensioner roller (1)to free the pegging hole at "a".
Peg the dynamic tensioner roller at "a", using tool [1].
WARNING: Do not compress the dynamic tensioner roller completely (risk
of damage).
WARNING: Mark the direction of fitting of the auxiliary equipment drive belt
if for re-use.
Disengage the auxiliary equipment drive belt from the various pulleys, commencing
at "b"(coolant pump pulley).
Remove:
- The screws (2)and (4).
- The dynamic tensioner roller (1).
- The auxiliary equipment drive belt (3).
ESSENTIAL: Check that the tensioner and guide rollers as well as the
coolant pump can turn freely (without play, without tight spots and without
projections of grease).
Angl-C6-page022-82-2005 4/02/05 17:19 Page 48

Downloaded from www.Manualslib.com manuals search engine 49
ENGINE
B1BP3BVC
AUXILIARY EQUIPMENT DRIVE BELT
Engine: DT17BTED4
Refitting.
WARNING: If re-using the auxiliary equipment drive belt, refit it respecting its direction of
fitting.
Fit the auxiliary equipment drive belt.
ESSENTIAL: Make sure that the auxiliaries drive belt is correctly positioned in the
grooves of the various pulleys.
Refit:
- The dynamic tensioner roller (1)by engaging the belt on the roller.
- The screws (2)and (4).
Tighten:
- Screw (2) : 5 ± 0,5.
- Screw (4) : 2,3 ± 0,2.
Compress the dynamic tensioner roller.
Remove tool [1].
ESSENTIAL: Make sure that the auxiliaries drive belt is correctly positioned in the
grooves of the various pulleys.
Refit:
- The air duct(linking the air distributor heat exchanger).
- The RH splash-shield.
- The front RH wheel.
- The under-engine sound-deadening.
Angl-C6-page022-82-2005 4/02/05 17:19 Page 49

Downloaded from www.Manualslib.com manuals search engine 51
ENGINE
51
CHECKING THE VALVE TIMING
Engine: ES9A
Tools.
[1]Camshaft setting pegs: (-).0187.B
[2]Crankshaft setting peg: (-).0187.A
[3]Fuel pressure take-off union: 4192-T
[4]Belt retaining pin: (-).0187.J
[5]Exhaust camshaft hubs immobilising tool: (-).0187.F
[6]Inlet camshaft hubs immobilising tool: FACOM D12
[7]SEEM belt tension measuring equipment: 4122-T
Remove components as necessary for this operation.
Remove the auxiliaries drive belt (see corresponding operation).
Checking the valve timing.
Remove:
- The power steering pulley.
- The roller/dynamic tensioner assembly (11).
- The crankshaft pulley (12).
- The upper timing covers (9)and (10).
- The lower timing cover (13).
B1BP2BKC
Angl-C6-page022-82-2005 4/02/05 17:19 Page 51