0106E±06
A54988
N´m (kgf´cm, ft´lbf) : Specified torque
Non±reusable partCamshaft Timing Tube AssyCamshaft Drive Gear
Seal Washer
Camshaft Setting Oil SealNo. 2 Camshaft,
No. 4 Camshaft Sub±assy
Wave WasherCamshaft Driven Main Gear
Snap RingCamshaft Timing Gear
Bolt Washer Screw Plug
78 (790, 58)
15 (150, 11)
7.5 (80, 66 in.´lbf)
Camshaft Sub Gear
Camshaft,
No. 3 Camshaft Sub±assy OVERHAUL
± INTRODUCTIONHOW TO USE THIS MANUAL
01±1
1CD±FTV ENGINE REPAIR MANUAL (RM927E)
HOW TO USE THIS MANUAL
GENERAL INFORMATION
1. GENERAL DESCRIPTION
(a) This manual is made in accordance with SAE J2008.
(b) Generally repair operations can be separated in the following 3 main processes:
1. Diagnosis
2. Removing and Installing, Replacing, Disassembling, Installing and Checking, Adjusting
3. Final Inspection
(c) This manual explains ºRemoving and Installing, Replacing, Disassembling, Installing and Checking,
Adjustingº, but ºFinal Inspectionº is omitted.
(d) The following essential operations are not written in this manual, however these operations must be
done in the practical situation.
(1) Operation with a jack or lift
(2) Cleaning of a removed part when necessary
(3) Visual check
2. INDEX
(a) An alphabetical INDEX is provided as a section on the end of the book to guide you to the item to be
repaired.
3. PREPARATION
(a) Use of special service tools (SST) and special service materials (SSM) may be required, depending
on the repairing condition. Be sure to use SST and SSM when they are required and follow the working
procedure properly. A list of SST and SSM is in the Preparation section of this manual.
4. REPAIR PROCEDURES
(a) Component drawing is placed as the section or title when necessary.
(b) Illustrations of the parts catalog are placed as the ºdisassembled parts drawingº so that it enables you
to understand the fitting condition of the components.
(c) Non±reusable parts, grease applied parts, precoated parts and tightening torque are specified in the
components drawing.
Example:
010BA±03
01±12
± INTRODUCTIONTERMS
1CD±FTV ENGINE REPAIR MANUAL (RM927E)
GLOSSARY OF SAE AND TOYOTA TERMS
This glossary lists all SAE±J1930 terms and abbreviations used in this manual in compliance with SAE rec-
ommendations, as well as their TOYOTA equivalents.
SAE
ABBREVIATIONSSAE TERMSTOYOTA TERMS
( )±±ABBREVIATIONS
A/CAir ConditioningAir Conditioner
ACLAir CleanerAir Cleaner, A/CL
AIRSecondary Air InjectionAir Injection (AI)
APAccelerator Pedal±
B+Battery Positive Voltage+B, Battery Voltage
BAROBarometric PressureHAC
CACCharge Air CoolerIntercooler
CARBCarburetorCarburetor
CFIContinuous Fuel Injection±
CKPCrankshaft PositionCrank Angle
CLClosed LoopClosed Loop
CMPCamshaft PositionCam Angle
CPPClutch Pedal Position±
CTOXContinuous Trap Oxidizer±
CTPClosed Throttle PositionLL ON, Idle ON
DFIDirect Fuel Injection (Diesel)Direct Injection (DI)
DIDistributor Ignition±
DLC1
DLC2
DLC3Data Link Connector 1
Data Link Connector 2
Data Link Connector 31: Check Connector
2: Total Diagnosis Comunication Link (TDCL)
3: OBD II Diagnostic Connector
DTCDiagnostic Trouble CodeDiagnostic Code
DTMDiagnostic Test Mode±
ECLEngine Control Level±
ECMEngine Control ModuleEngine ECU (Electronic Control Unit)
ECTEngine Coolant TemperatureCoolant Temperature, Water Temperature (THW)
EEPROMElectrically Erasable Programmable Read Only Memory
Electrically Erasable Programmable Read Only Memory
(EEPROM),
Erasable Programmable Read Only Memory (EPROM)
EFEEarly Fuel EvaporationCold Mixture Heater (CMH), Heat Control Valve (HCV)
EGRExhaust Gas RecirculationExhaust Gas Recirculation (EGR)
EIElectronic IgnitionTOYOTA Distributorless Ignition (TDI)
EMEngine ModificationEngine Modification (EM)
EPROMErasable Programmable Read Only MemoryProgrammable Read Only Memory (PROM)
EVAPEvaporative EmissionEvaporative Emission Control (EVAP)
FCFan Control±
FEEPROMFlash Electrically Erasable Programmable
Read Only Memory±
FEPROMFlash Erasable Programmable Read Only Memory±
FFFlexible Fuel±
FPFuel PumpFuel Pump
GENGeneratorAlternator
GNDGroundGround (GND)
B08059
B08067
B08068
Seal Surface
Shroud Section
B08065
Inside Diameter Section
B08066
13±4
± INTAKETURBOCHARGER ASSEMBLY (1CD±FTV)
1CD±FTV ENGINE REPAIR MANUAL (RM927E)
(c) Using a plastic±faced hammer, tap out the bearing hous-
ing.
NOTICE:
Remove the bearing housing as straight as possible and do
not make the turbine wheel interfere with the turbine hous-
ing.
6. CLEAN TURBINE HOUSING
(a) Spray the engine conditioner to the section where the car-
bon dirt is adhered.
NOTICE:
Be careful not to erase the matchmark of the turbine hous-
ing.
(b) Using a wire brush, remove all the carbon dirt inside the
turbine housing.
NOTICE:
Clean the seal surface and shroud section shown in the il-
lustration sufficiently. And clean the waste gate valve seat
sufficiently, too.
HINT:
When the carbon dirt is heavily adhered, remove it using the
screwdriver and the like.
(c) Clean the inside diameter section with a sandpaper (No.
100) until the metal surface can be seen.
NOTICE:
If the cleaning is not enough, installation of the bearing
housing becomes harder, so clean it sufficiently.
(d) Wash with compressed air or a steam cleaner.
NOTICE:
Wash sufficiently without leaving any irregular objects.
