2004 SUBARU LEGACY Owners Manual

11 - 8
2Maintenance and service
Engine compartment overview „
2.5 liter models
12 3 45678
9
10
11
12
13
14
UBB036BB
1) Manual transmission oil level
gauge (MT) (page 11-27) or Dif-
ferential gear oil level gauge
(AT) (page 11-30)
2) Air cleaner element (page 11- 22)
3) Clutch fluid reservoir (page 11-
38)
4) Automatic transmission fluid lev- el gauge (page 11-28)
5) Brake fluid reservoir (page 11- 36)
6) Fuel filter
7) Windshield washer tank (page 11-51)
8) Fuse box (page 11-59)
9) Battery (page 11-58)
10) Engine oil filler cap (page 11-11)
11) Engine coolant reservoir (page
11-18)
12) Radiator cap (page 11-18)
13) Engine oil level gauge (page 11-
11)
14) Power steering fluid reservoir (page 11-35)

11 - 9
2Maintenance and service
– CONTINUED –
„2.5 liter CALIFORNIA spec models
1
13 12 10 11 9 8
23
45 67
UBB099BB
1) Air cleaner element (page 11-
22)
2) Manual transmission oil level gauge (MT) (page 11-27) or Dif-
ferential gear oil level gauge
(AT) (page 11-30)
3) Clutch fluid reservoir (page 11-
38)
4) Automatic transmission fluid lev- el gauge (page 11-28)
5) Brake fluid reservoir (page 11- 36)
6) Windshield washer tank (page
11-51)
7) Fuse box (page 11-59)
8) Battery (page 11-58)
9) Engine oil filler cap (page 11-11)
10) Engine coolant reservoir (page 11-18)
11) Engine oil level gauge (page 11- 11)
12) Radiator cap (page 11-18)
13) Power steering fluid reservoir (page 11-35)

11 - 1 0
2Maintenance and service „
3.0 liter models
12 3 45 67
8
9
10
11
12
13
UBB058BB
1) Air cleaner element (page 11-
22)
2) Differential gear oil level gauge (AT) (page 11-30)
3) Automatic transmission fluid lev- el gauge (page 11-28)
4) Brake fluid reservoir (page 11-
36)
5) Fuel filter
6) Windshield washer tank (page
11-51)
7) Fuse box (page 11-59)
8) Battery (page 11-58)
9) Engine oil filler cap (page 11-11)
10) Engine coolant reservoir (page 11-18)
11) Engine oil level gauge (page 11- 11)
12) Radiator cap (page 11-18)
13) Power steering fluid reservoir (page 11-35)

11-11
2Maintenance and service
– CONTINUED –
Engine oil „Checking the oil level
Check the engine oil level at each fuel stop.
1. Park the vehicle on a level surface and stop the en-
gine.
2. Pull out the dipstick, wipe it clean, and insert it
again.
3. Be sure the dipstick is correctly inserted until it
stops with the graphic symbol on its top appear-
ing as shown in the illustration. 1) Notch (except 3.0L)
2) Upper level
3) Lower level
4. Pull out the dipstick again and check the oil level on
it. If it is below the lower level, add oil to bring the level
up to the upper level.
Use only engine oil with the recommended
grade and viscosity.
If you check the oil level just after stopping the engine,
UBB004JA
1 2
3
UGB082BB

11 - 1 2
2Maintenance and service
wait a few minutes for the oil to drain back into the oil
pan before checking the level.
To prevent overfilling the engine oil, do not add any
additional oil above the upper level when the engine is cold.
In 2.5-liter-engine models, the dipstick has a notch
above the upper level.
Just after driving or while the engine is warm, the en-
gine oil level reading may be in a range between the
upper level and the notch mark. This is caused by ther-
mal expansion of the engine oil. „
Changing the oil and oil filter
Change the oil and oil filter according to the mainte-
nance schedule in the “Warranty and Maintenance
Booklet”.
The engine oil and oil filter must be changed more fre-
quently than listed in the maintenance schedule when
driving on dusty roads, when short trips are frequently
made, or when driving in extremely cold whether.
1. Warm up the engine by letting the engine idle for
about 10 minutes to ease draining the engine oil.
2. Park the vehicle on a level surface and stop the en-
gine.
3. Remove the oil filler cap. 1) Drain plug
4. Drain out the engine oil by removing the drain plug
while the engine is still warm. The used oil should be
drained into an appropriate container and disposed of
properly.
Be careful not to burn yourself with hot engine
oil.
1
UBB005BB

11 -1 3
2Maintenance and service
– CONTINUED –
1) Sealing washer
2) Drain plug
5. Wipe the seating surface of the drain plug with a
clean cloth and tighten it securely with a new sealing
washer after the oil has completely drained out. 6. Remove three clips at the front of the cover under
the oil filter.
1
2
UBB051BBUBB054BA

11 - 1 4
2Maintenance and service
7. Slide the cover toward the vehicle front to remove it.
8. Remove the oil filter with an oil filter wrench.
9. Before installing a new oil filter, apply a thin coat of
engine oil to the seal.
10.Clean the rubber seal seating area of the bottom of
engine and install the oil filter by hand turning. Be
careful not to twist or damage the seal.
11.Tighten it approximately two-thirds of a turn after
the seal makes contact with the bottom of engine.
Never over tighten the oil filter because that can
result in an oil leak.
12.Reinstall the cover under the oil filter.
13.Pour engine oil through the filler neck.
Oil capacity (Guideline): 2.5 liter models: 4.2 US qt (4.0 liters, 3.5 Imp qt)
3.0 liter models: 5.6 US qt (5.3 liters, 4.6 Imp qt)
The oil quantity indicated above is only a guideline.
The necessary quantity of oil depends on the quantity
of oil that has been drained. The quantity of drained oil
differs slightly depending on the temperature of the oil
and the time the oil is left flowing out. After refilling the
engine with oil, therefore, you must use the dipstick to
confirm that the level is correct.
14.Start the engine and make sure that no oil leaks ap-
pear around the filter’s rubber seal and drain plug.
15.Run the engine until it reaches the normal operat-
ing temperature. Then stop the engine and wait a few
minutes to allow the oil drain back. Check the oil level
again and if necessary, add more engine oil.
UBB055BA

11 -1 5
2Maintenance and service
– CONTINUED –
„Recommended grade and viscosity
Use only engine oil with the recommended
grade and viscosity.
Oil grade:
ILSAC GF-3, which can be identified with the new
API certification mark (Starburst mark)
or API classification SL with the words “ENERGY
CONSERVING” (if you cannot obtain the oil with
SL grade, you may use SJ grade “ENERGY CON-
SERVING” oil).
These recommended oil grades can be identified by
looking for either or both of the following marks dis-
played on the oil container. New API Certification Mark (Starburst Mark)
AMERICANPETROLEUMINSTITUTE
CERTIFIED
HSB023AA