2004 MITSUBISHI ENDEAVOR traction control

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

Fig. 215: Checking Junction block connector C
-211 and C
-215

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Ignition switch connector C-308
Fig. 216: Checking Ignition switch connector C
-308

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Steerin
g wheel sensor connector C-312

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

Fig. 217: Checking Steering Wheel Sensor Connector C
-312

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Check the connectors, for loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Are the connectors and terminals in good condition?
YES: An open or short circuit may be present in the power supply line to
the steering wheel sensor. Repair the wiring harness between steering
wheel sensor connector C-312 terminal 2 and ignition switch connector C-
308 terminal 4. Go to Step 8.
NO: Repair or replace the damaged component(s). Then go to Step 8.
STEP 3. Measure the resistance at steering wheel sensor connector C-312.
1. Disconnect the steering sensor connector C-312, and measure at the
harness side connector.

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

2. Measure the resistance between terminal 5 and bod
y ground.

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

Fig. 218: Measuring Resistance At Steering Wheel Sensor Connector C-312

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the measured resistance 2 ohms or less?
YES: Go to Step 5.
NO: Go to Step 4.
STEP 4. Check steering wheel sensor connector C-312 for loose, corroded
or damaged terminals, or terminals pushed back in the connector.
Fig. 219: Checking Steering Wheel Sensor Connector C
-312

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are the connectors and terminals in good condition?

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

YES: An open circuit may be present in the ground circuit. Repair the
wiring harness between steering wheel sensor connector C-312 terminals 5
and the body ground. Then go to Step 8.
NO: Repair or replace the damaged component(s). Then go to Step 8.
STEP 5. Check the battery.
Check the battery (Refer to BATTERY TEST
).
Q: Is the battery in good condition?
YES: Go to Step 6.
NO: Charge or replace the battery. Then go to Step 8.
STEP 6. Check the charging system.
Check the charging system (Refer to GENERATORS & REGULATORS
).
Q: Is the charging system in good condition?
YES: Go to Step 7.
NO: Repair or replace the charging system component(s). Then go to Step
8.
STEP 7. Retest the system.
Q: Can the steering wheel sensor communicate with the scan tool (MUT-
III Sub Assembly)?
YES: It can be assumed that this malfunction is intermittent. Refer to
HOW TO COPE WITH INTERMITTENT MALFUNCTIONS
.
NO: Replace the steering wheel sensor. Then go to Step 8.
STEP 8. Retest the system.
Q: Can the steering wheel sensor communicate with the scan tool (MUT-
III Sub Assembly)?
YES: The
procedure is com
plete.

2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor

NO: Go to Step 1.
INSPECTION PROCEDURE 5: G and yaw rate sensor power supply system
2004 Mitsubishi Endeavor LS
2004 BRAKES Traction Control, Active Skid Control System - Endeavor