2004 MITSUBISHI ENDEAVOR diagnosis

2004 Mitsubishi ENDEAVOR 04 - Engine > ENGINE AND ENGINE COOLING :
ENGINE [Part 061000 ]
TSB No: 0413004 NHTSA ID: , July 01, 2004 : Replacement: 0413004R
Summary: power train control module (pcm) reprogramming for spark knock / diagnostic
trouble code (dtc) 0171. *tt

2004 Mitsubishi ENDEAVOR 04 - Power Train > POWER TRAIN [Part 100000 ]
TSB No: 0423001 NHTSA ID: , July 01, 2004 : Replacement: 0423001R
Summary: power train control module (pcm) reprogramming for a/t shift delay. *tt

2004 Mitsubishi ENDEAVOR 04 - Equipment > EQUIPMENT [Part 350000 ]
TSB No: 0454004 NHTSA ID: , May 01, 2004 : Replacement:
Summary: overhead console service parts. *tt

2004 Mitsubishi ENDEAVOR 04 - Air Bag > AIR BAGS [Part 140000 ]
TSB No: 0452B002 NHTSA ID: , March 01, 2004 : Replacement:
Summary: corrected advanced air bag troubleshooting procedures - service manual
revision. *tt

2004 Mitsubishi ENDEAVOR 04 - Differential Unit > POWER TRAIN : DRIVELINE
: DIFFERENTIAL UNIT [Part 105500 ]
TSB No: 0427001 NHTSA ID: , February 01, 2004 : Replacement:
Summary: rear differential noise diagnosis. *mr

2004 Mitsubishi ENDEAVOR 04 - Electrical Equipment > EQUIPMENT :
ELECTRICAL [Part 353000 ]
TSB No: 0442A001 NHTSA ID: , February 01, 2004 : Replacement:
Summary: remote keyless entry (all 2004 models). *tt

2004 Mitsubishi ENDEAVOR 04 - ABS Antilock > SERVICE BRAKES,
HYDRAULIC : ANTILOCK [Part 036000 ]
TSB No: 0435002 NHTSA ID: , January 01, 2004 : Replacement:
Summary: abs and tcl diagnostic trouble codes - service manual revision. *tt

2004 BODY & ACCESSORIES
Rear Wiper And Washer - Endeavor
GENERAL DESCRIPTION REAR WIPER OPERATION
If the rear wiper and washer switch is turned to the "INT" position with the
ignition switch at "ACC" or "ON" position, the ETACS-ECU turns ON the rear
wiper drive signal for three seconds (approximately two cycles), then 7.4
seconds later the intermittent motion operates every eight seconds. If the
selector lever is moved to the "R" position when the rear wiper and washer
switch is turned to the "INT" position and the ignition switch is at the "ACC"
or "ON" position, the park/neutral position switch "R" turns ON. One second
later, the ETACS-ECU turns ON the rear wiper drive signal for three seconds
(approximately two cycles). Then, 7.4 seconds later, the intermittent operation
(eight second cycles) is restored.
REAR WASHER OPERATION
If the rear wiper and washer switch is turned to the ON (washer) position with
the ignition switch at the "ACC" or "ON" position, the rear washer ON signal
is sent to the ETACS-ECU, causing the rear wiper signal to turn on after 0.3
seconds. After the rear washer switch signal turns off, the rear wiper signal
turns off in three seconds. If the rear washer switch is turned to the ON
position while the rear wiper is in intermittent mode, the rear washer works for
that period when the washer switch remains on. Then the rear wiper returns to
the intermittent mode.
REAR WIPER AND WASHER DIAGNOSIS The rear wiper and washer are controlled by the Simplified Wiring System (SWS).
For troubleshooting, refer to SWS DIAGNOSIS
.
ON-VEHICLE SERVICE CHECK OF REAR WIPER OPERATION WHEN SELECTOR LEVER IS AT THE "R" POSITION
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Rear Wiper And Washer - Endeavor


2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Rear Wiper And Washer - Endeavor

1. When the selector lever is moved to the "R" position with the rear wiper switch
at the "INT" position, the wiper should operate twice or three times at low
speed after approximately one second.
2. If not, troubleshoot (Refer to SWS DIAGNOSIS
).
REAR WIPER MOTOR CHECK Inspect the rear wiper motor by removing the harness connector with the motor still
installed in the vehicle. WIPER MOTOR OPERATION 1. Remove the motor cover (Refer to REAR WIPER AND WASHER
).
2. Connect the rear wiper motor connector terminal num
ber 1 to the ground.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Rear Wiper And Washer - Endeavor

If the windshield mist wiper switch is turned to the ON position, with the
ignition switch at the "ACC" or "ON" position, the mist wiper high-speed
operation signal is sent to the front-ECU. This signal turns on the wiper speed
control relay, causing the wipers to work at high-speed while the mist switch is
on. While the windshield mist wiper switch remains turned on when the
intermittent mode is still working, the wipers work as the mist wiper. However,
the wipers return to the intermittent mode again when the switch is changed
back to "INT" position. To prevent the windshield mist wiper from operating when the windshield
wiper switch is turned OFF, the windshield mist wiper does not work for 0.5
second after the windshield intermittent wiper switch, the windshield low-
speed wiper switch and the windshield high-speed wiper switch are turned
OFF.
WINDSHIELD WASHER OPERATION
If the windshield washer switch is turned to the ON position with the ignition
switch at "ACC" or "ON" position, the windshield washer ON signal is sent to
the front-ECU. After 0.3 second, the windshield wiper signal turns on. After
the windshield washer switch signal turns off, the windshield wiper signal
turns off in three seconds. If the windshield washer switch is turned on while the windshield wiper is at
intermittent mode, and the windshield washer switch is turned OFF within 0.2
second, the wiper works only once to perform mist operation. When the
windshield washer switch is turned on for more than 0.2 second, the wiper
performs the same movement as normal condition from the time when 0.2
second has elapsed, and then returns to intermittent operation.
WINDSHIELD WIPER AND WASHER DIAGNOSIS The windshield wiper and washer are controlled by the Simplified Wiring System
(SWS). For troubleshooting, refer to SWS DIAGNOSIS
.
NOTE: Even when the ETACS-ECU has failed, the windshield wiper
can work at low speed in fail-safe mode. (Normally, the

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Windshield Wiper And Washer - Endeavor

ON-VEHICLE SERVICE WINDSHIELD INTERMITTENT WIPER VOLUME CHECK 1. If the windshield intermittent wiper volume is operated, the wiper interval
should change.
2. Holding the windshield intermittent wiper volume, input the simulated vehicle
speed with scan tool MB991958 and check that the wiper interval changes as
the vehicle speed changes.
3. If not, carry out the troubleshooting (Refer to SWS DIAGNOSIS
).
WINDSHIELD WASHER FLUID EJECTION CHECK The windshield washer nozzle aiming can not be adjusted. If the washer nozzles do
not spray washer fluid within the swept area, check the nozzles as follows.
1. Check that the windshield washer nozzles are fitted on the hood correctly, and
reinstall them if necessary. windshield wiper operates when the ignition switch is at the
"ACC" or "ON" position. But, if it enters the fail-safe mode,
the wiper can operate only when the ignition switch is at the
"ON" position).
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Windshield Wiper And Washer - Endeavor