2004 MITSUBISHI ENDEAVOR engine oil

Fig. 13: Identifying API Service Symbol (Up To December 2003)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
ENGINE OIL < FROM JANUARY 2004 > Use onl
y en
gine oils conformin
g to the ILSAC G
F-3 certification.
CAUTION: Never use nondetergent or straight mineral oil.

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Lubrication - Endeavor

Fig. 14: Identifying ILSAC Certification Symbol (From January 2004)

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
If these oils are not available, an API classification SL, SL/CF can be used.

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Lubrication - Endeavor

Fig. 5: Holding The Drive Plate Or Flywheel Using Special Tool MD998781

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Clean the bolt hole in crankshaft bolt, damper pulley seating surface and the
washer.
3. Degrease the cleaned seating surface of the damper pulley.
4. Install the damper pulley.
5. Apply a minimum amount engine oil to the thread and lower flange of the
crankshaft bolt.
6. Install the washer to the crankshaft bolt with its inside chamfered side toward
the bolt head.
7. Tighten the crankshaft bolt to the specified torque.
Tightening torque: 185+/-5 N.m (137+/-3 ft-lb)

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

MD998715: Pins MD998767: Tensioner Pulley Wrench MD998769: Crankshaft Spacer
REMOVAL SERVICE POINTS << A >> TIMING BELT REMOVAL 1. Mark the belt running direction for reinstallation.
2. Loosen the tensioner pulley bolt, and then remove
the timing belt.
CAUTION: Water or oil on the belt shortens its life drasticall
y, so
the removed timing belt, sprocket, and tensioner
must be kept free from oil and water. These parts
should not be washed or immersed in solvent.
Replace parts if contaminated. If there is oil or water
on any part, check the front case oil seal, camshaft
oil seal, and water pump for leaks.

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

1. Install special tool MD998769 and the crankshaft pulley washer, and then
tighten the crankshaft bolt.
2. Align the timing mark on the crankshaft sprocket with the timing mark on the
oil pump case, and then rotate the sprocket three teeth counterclockwise.
Fig. 24: Aligning The Timing Mark On Crankshaft Sprocket & Timing
Mark On Oil Pump Case

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. Align the timing mark on the left bank camshaft sprocket with the timing mark
on the rocker cover.
4. Align the timing mark on the right bank camshaft sprocket with the timing
mark on the rocker cover.

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

Fig. 25: Align The Timing Mark On The Right Bank Camshaft Sprocket With Timing Mark On Rocker Cover

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
5. Align the timing mark on the crankshaft sprocket with the timing mark on the
oil pump case.
6. Install the timing belt on each sprocket and pulley in the following sequence.
Do not leave the belt slack between each sprocket and pulley.
1. Crankshaft sprocket
2. Idler pulley
3. Left bank camshaft sprocket
4. Water pump pulley
5. Right bank camshaft sprocket
6. Tensioner
pulle
y

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

AUT
O-TENSIONE
R
1. Check for oil leaks. If oil leaks are evident, replace the auto-tensioner.
2. Check the rod end for wear or damage and replace the auto-tensioner if
necessary.
3. Measure the rod protrusion. If it is out of specification, replace the auto-
tensioner.
Standard value: 12 mm (0.5 inch)
Fig. 38: Checking Auto
-Tensioner

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
4. Press the rod with a force of 98 to 196 N (22 to 44 pounds) and measure the
movement of the rod.
If the measured value is out of the standard value
, re
place the auto-tensioner.

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor

Tightening torque: 22+/-1 N.m (16+/-1 ft-lb)
>>B<< INJECTOR INSTALLATION 1. Apply clean engine oil to the O-ring.
2. Insert the injector into the fuel rail.
Fig. 43: Installing Injector

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. Make sure the injector rotates smoothly. If not, remove the injector to check
the O-ring for damage, and replace the O-ring if necessary. Then reinsert the
injector and check that it rotates smoothly.
4. Confirm the
protrusion of in
jector is at center. I
f not
, rotate the in
jector fo
r
CAUTION: Use care not to let engine oil enter the fuel rail.

2004 Mitsubishi Endeavor Limited 2004 ENGINE Engine Overhaul - Endeavor