Page 915 of 3870
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 916 of 3870
Fig. 68: Connecting Special Tool MB991923
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. Turn the ignition switch to the "ON" position.
4. Measure the terminal voltage between special tool 23-pin connector
(without red tape) terminal 33 (PCM connector B-19 terminal 33) and
ground.
When the brake pedal is depressed, the voltage should measure
battery positive voltage (approximately 12 volts). When the brake pedal is released, the voltage should measure 1 volt
or less.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 917 of 3870
Fig. 69: Measuring Terminal Voltage Between Special Tool 23
-
Pin Connector Terminal 33 And Ground
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
5. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage battery positive voltage (approximately 12
volts) when the brake pedal is depressed and 1 volt or less when the brake
pedal is released?
YES : Go to Step 21 .
NO : Go to Step 16.
STEP 16. Check PCM connector B-19 and stoplight switch connector C-03
for loose, corroded or dama
ged terminals, or terminals
pushed back in the
connector.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 918 of 3870
Fig. 70: Checkin
g PCM Connector
B-19
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 919 of 3870
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
Fig. 71: Checking Stoplight Switch Connector C
-03
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are the connector and terminals in good condition?
YES : Go to Step 17.
NO : Repair or replace the damaged components. Then go to Step 22 .
STEP 17. Check the harness wire between PCM connector B-19 terminal
33 and stoplight switch connector C-03 terminal 3 for damage.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 920 of 3870
Fig. 72: Check Harness Wire Between PCM Connector B
-19 Terminal 33
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 921 of 3870
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
Fig. 73: Identifying Connector C
-03
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the harness wire in good condition?
YES : Go to Step 18.
NO : Repair the damaged harness wire. Then go to Step 22 .
STEP 18. Check the harness wire between stoplight switch connector C-03
terminal 4 and ground for damage.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
Page 922 of 3870
Fig. 74: Identifying Connector C
-03
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the harness wire in good condition?
YES : Go to Step 19.
NO : Repair the damaged harness wire. Then go to Step 22 .
STEP 19. Check the stoplight switch.
1. Remove the stoplight switch (Refer to , BRAKE PEDAL ).
2. Connect an ohmmeter to the stoplight switch between terminals 3 and 4.
2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor
