2004 MERCEDES-BENZ E-Class Comand Manual

24 At a glanceMultifunction steering wheelTelephone* operation:
Either the main display, or a list appears on
display.
Telephone main display:
In the list screen, instead of the READY
message, either a phone book entry or one
of the last 10 outgoing calls will be dis-
played.
In order to close the list display,
presst
.
This switches to the telephone main
display.

25 At a glance
Menu system

Menu system
The menu system allows for easy opera-
tion of COMAND.
Each of the following main functions has a
main menu: 
Audio
(Radio, Single CD, CD changer* and
AUX mode)

Satellite radio*

Navigation*

Telephone*

Service
Opening main menus

Audio (
page 34):
Press
.

Satellite radio* (
page 61):
Press .

Navigation* (
page 98):
Press .

Telephone* (
page 77):
Press .

Service (
page 141):
Press .
Menu display
A display can be composed of 3 sections.
Example: Radio main menu
1Soft key sections
2Main area
3Status barThe functions currently assigned to the
soft keys are displayed in the soft key sec-
tions 1.
Messages or settings are displayed in the
main area 2.
The settings can be changed by operating
controls accordingly.
The status bar 3 is divided into three ar-
eas.
Left side:
The selected operating mode is given. In
this example: Radio
iA maximum of five soft keys may be
displayed on each side of the main area
2.

26 At a glanceMenu systemCenter:
Indication of the selected operating mode.
In this example:

FM = selected waveband

1 = selected station is stored on
preset 1
Right side:
General status information is displayed, re-
gardless of the selected operating mode.
In this example:

ROAMING = telephone* is logged into a
mobile communications network out-
side your home network.

= telephone* signal strengthMenu functions and submenus
Using the soft keys, you can switch func-
tions ON or OFF, or open submenus.
Example: Radio main menu:

The Scan soft key switches the scan
search ON or OFF.

The Autost. soft key opens the sub-
menu for the Autostore settings.In some situations, soft keys may not have
any function and thus not be available.
Should a soft key not be available, it will
appear shaded out, its characters will ap-
pear white.
Example:
Presets, Scan and Autost. soft key.

27 At a glance
Menu system
Exiting from submenus
You can exit the current submenu by
pressing the Back soft key. The display
switches to the next higher menu level.
The system does not accept setting modi-
fications which have not been stored.
There are exceptions where pressing the
Back soft key will also store new settings.
These exceptions, whenever applicable,
are referenced on the following pages.

28 At a glanceQuick reference COMANDSwitching ON 
Turn the key in the steering lock to po-
sition 1 or 2,
or

Press .
COMAND switches on the last active
system and displays the corresponding
menu.
Switching OFF

Turn the key in the steering lock to po-
sition 0 and remove it,
or

Press .Different volume settings are possible for
navigation*, telephone*, or Voice con-
trol*.
A common volume setting is provided for
Radio, Single CD, CD changer*, AUX and
Satellite radio* operating modes.
When setting the volume, the system auto-
matically stores the setting for the current-
ly active operating mode. The volume of
navigation announcements can be
changed only during an actual announce-
ment.
iThe system can be operated as follows:
from COMAND itself, or

from the multifunction steering
wheel
This operating manual describes oper-
ation from COMAND and from the mul-
tifunction steering wheel.
Unless otherwise specified, the de-
scriptions and the displays illustrated
relate to the COMAND control unit.
Switching ON/OFF
iWithout the key in position 1 or 2 of the
steering lock, the system automatically
switches OFF again after approx. 30
minutes of inactivity.
iIf a telephone call is in progress (hands-
free) you cannot switch the COMAND
OFF, is disabled.Volume

29 At a glance
Quick reference COMAND
Setting the volume 
Turn the rotary control
located on
the COMAND control unit,
or

Pressæ or ç on the multifunc-
tion steering wheel
The volume changes up or down, de-
pending on the direction of rotation or
which button was pressed.The system stores the volume settings
when the device is switched OFF.
After switching the system back on again,
the volume may be lower than at the time
when the system was switched off.
This could be the case if
the system was switched off for more
than 15 minutes, and

the volume had been set to a value in a
certain range at the time the device
was switched OFF.
Automatic volume control
The automatic volume control adjusts the
volume depending on

the vehicle’s speed (only in vehicles
without Sound-system*),
or on
the interior ambient noises of the vehi-
cle (only in vehicles with Sound-sys-
tem*)

other parameters (e.g. windows open
or closed)A common balance and fader setting ap-
plies to the following operating modes:

Radio

Single CD

CD changer*

AUX

Satellite radio*
When adjusting the balance or the fader,
the system automatically stores the set-
ting for the currently active operating
mode.Balance and faderiFor navigation* a different balance/
fader setting is possible. You find the
description under “Adjusting the
acoustics for navigation announce-
ments” (
page 99).

30 At a glanceQuick reference COMANDSetting balance/fader
Open the main menu of the appropriate
operating mode (
page 25).

Press the Bal/Fad soft key.
The Balance/Fader menu is displayed.
Now you can set the balance and the
fader (
page 30).
A cross-hair cursor appears. The verti-
cal line indicates the balance setting.
The horizontal line indicates the fader
setting.

Press or :
The cursor moves horizontally, adjust-
ing the desired balance,
or

Press or :
The cursor moves vertically, adjusting
the fader.
Storing new settings:

Press or the Back soft key,
or

wait until the display changes.For the following operating modes, differ-
ent settings for bass and treble can be se-
lected:

Radio (FM waveband)

Radio (AM waveband)

Radio (Weather Band)

Single CD

CD changer*

AUX

Satellite radio*

Navigation*
Bass and treble settings for navigation an-
nouncements are found under “Adjusting
the acoustics for navigation announce-
ments” (
page 99).
When adjusting bass or treble, the system
automatically stores the setting for the
currently active operating mode.
i Using  and , the cursor can be
moved simultaneously in vertical and
horizontal direction (diagonally).
Bass and treble

31 At a glance
Quick reference COMAND
Setting bass and treble
Open the main menu of the appropriate
operating mode (
page 25).

Press the Bass or Treble soft key.
The Bass or Treble menu appears.
Storing new settings:

Press or the Back soft key,
or

wait until the display changes.If the vehicle is equipped with a sound sys-
tem*, the sound functions are available for
the following operating modes:

Radio

Single CD

CD changer*

AUX

Satellite radio*
Different sound functions* can be activat-
ed for each one of the operating modes
listed above.
Example:
For CD mode: the LOGIC7 Surround func-
tion,
for Satellite radio* mode: the Speech
function.The following sound functions are avail-
able:

Default Settings:
Resets the sound functions* to the fac-
tory setting.

Standard:
Normal stereo playback.

Speech:
Playback optimized for speech compre-
hension.

LOGIC7 Surround:
7-channel-surround playback (not for
mono-sources like AM waveband or
Weather Band in radio mode).
Switching sound functions* ON

Open the main menu of the appropriate
operating mode (
page 25).

Press the Sound soft key.
Sound functions*