2004 ISUZU TF SERIES check oil

UNIT REPAIR (AW30–40LE) 7A4–51
13. Install two plates and two discs then install the
flange, with the flat side facing downward.
2 52L10 001 3
14. Install snap ring.
2 52L10 001 4
15. Check piston stroke of OD direct clutch (C–0)
Place the oil pump onto the torque converter, and
then place the OD direct clutch assembly onto the
oil pump.
25 2L10 0005Using a dial indicator, measure the OD direct clutch
piston stroke by applying and releasing the
compressed air (390 – 780 kPa or 57 – 114 psi) as
shown.
Piston stroke: 1.85 – 2.15 mm (0.0729 – 0.0847 in)
If the piston stroke is not within specification,
replace the disc and recheck the piston stroke.
If the piston stroke is nonstandard, select another
flange.
Flange sizes
25 2L10 0016
Flange thickness Flange thickness
3.8 mm (0.150 in) 3.4 mm (0.134 in)
3.7 mm (0.146 in) 3.3 mm (0.130 in)
3.6 mm (0.142 in) 3.2 mm (0.126 in)
3.5 mm (0.138 in) 3.1 mm (0.122 in)

UNIT REPAIR (AW30–40LE) 7A4–53
OD Support Assembly
Disassembled View
2 52R20 0003
E nd O FCallo ut
Disassembly
1. Check OD brake piston movement.
Place the OD support assembly onto the direct
clutch assembly.
25 2RY 0 0042
Legend
(1) Thrust bearing
(2) Race
(3) Thrust washer (plastic)
(4) Snap ring(5) Piston return spring
(6) OD brake piston
(7) O-ring
(8) Oil seal ring
(9) OD support

7A4–54 UNIT REPAIR (AW30–40LE)
Apply compressed air into the oil passage as
shown, and be sure that the OD brake piston moves
smoothly.
25 2RY 0 004 3
2. Remove the thrust bearing.
3. Remove the race.
4. Remove the thrust washer (plastic).
5. Place special tool on the spring retainer, and
compress the return spring with a shop press.
Spring compressor : J–37233
Remove the snap ring with a screwdriver.
RUW 37A SH00 310 1
6. Romove the piston return spring.7. Place the OD support onto the direct clutch
assembly.
Hold the OD brake piston so it is not slanted and
apply compressed air into the passage to remove
the OD brake piston.
Remove the OD brake piston.
25 2RY 0 0045
8. Remove the O-ring and oil seal rings from OD
support.
Inspection and Repair
Make necessary correction or parts replacement if wear,
damage or any abnormal conditions are found through
inspection.
1. Check piston return spring
Using calipers, measure the free length of the return
spring.
Standard length: 17.2 mm (0.677 in)
25 2RY 0 0046

7A4–66 UNIT REPAIR (AW30–40LE)
5. Place special tool on the spring retainer and
compress the return spring.
Using snap ring pliers, remove the snap ring.
Spring compressor : J–25048
24 8RY 0 000 3
6. Remove the piston return spring.
7. Place the forward clutch drum onto the OD support.
Holding the forward clutch piston by hand, apply
compressed air to the OD support to remove the
forward clutch piston.
24 8RY 0 004 2
8. Remove the O-rings from piston.
9. Remove the O-ring from forward clutch drum.
10. Remove the oil seal rings and thrust bearing from
forward clutch drum.
Inspection and Repair
1. Check forward clutch piston
Check that check ball is free by shaking the piston.
Check that the valve does not leak by applying
low-pressure compressed air.
24 8RY 0 0031
2. Check forward clutch drum bushing.
Using a dial indicator, measure the inside diameter
of the forward clutch drum bushing.
Maximum inside diameter: 24.08 mm (0.948 in)
If the inside diameter is greater then the maximum,
replace the forward clutch drum.
24 8RY 0 0043
3. Check disc, plate and flange.
Check to see if the sliding surface of the disc, plate
and flange are worn or burnt. If necessary, replace
them.
If the lining of the disc is peeling off or discolored,
or even if parts of the printed numbers are
defaced, replace all discs.

UNIT REPAIR (AW30–40LE) 7A4–67
Before assembling new discs, soak them in ATF
for at least fifteen minutes.
24 8RY 0 004 5
4. Check piston return spring.
Using calipers, measure the free length of the return
spring.
Standard length: 19.47 mm (0.7665 in)
24 7RY 0 003 4
Reassembly
1. Coat the assembled thrust bearing and race with
petroleum jelly and install it onto the forward clutch
drum, with the race side facing downward.
Bearing and race (Reference)
24 8RY 0 0044
2. Coat the three oil rings with ATF.
Contract the oil seal rings as shown, and install
three oil seal rings onto the forward clutch drum.
NOTE: Do not spread the ring ends more than
necessary.
24 8RY 0 0046
Inside diameter 33.7 mm (1.327 in)
Outside diameter 47.8 mm (1.882 in)

7A4–74 UNIT REPAIR (AW30–40LE)
Disassembly
1. Check operation of No.1 one-way clutch
Hold the planetary sun gear and turn the second
brake hub.
The second brake hub should turn freely clockwise
and should lock counterclockwise.
RUW 37A SH00 460 1
E nd OFCa llou t
2. Remove the one-way clutch and second brake hub.
3. Remove the trust washer (plastic).
4. Remove two oil seal rings (metal).
24 8RY 0 005 2
5. Remove the snap ring with snap ring pliers.
24 8RY 0 0053
6. Remove the sun gear input drum.
7. Remove the snap ring from planetary sun gear.
Inspection and Repair
1. Check planetary sun gear bushing
Using a dial indicator, measure the inside diameter
of the planetary sun gear bushing.
Maximum inside diameter: 27.08 mm (1.066 in)
If the inside diameter is greater than the maximum,
replace the planetary sun gear.
24 8RY 0 0054
Legend
(1) Free
(2) Lock

7A4–82 UNIT REPAIR (AW30–40LE)
Disassembly
1. Remove second brake assembly from output shaft.
24 6RY 0 001 4
2. Remove oil seal ring from output shaft.
24 7RY 0 002 8
3. Remove the seven discs, seven plates and flange
(B–3).4. Remove rear planetary gear from rear planetary ring
gear.
24 7RY 0 0029
5. Check operation of No.2 one-way clutch.
Hold the planetary gear and turn the one-way clutch
inner race.
The one-way clutch inner race should turn freely
counterclockwise and should lock clockwise.
RUW3 7A SH00 4701
E nd OFCa llou t
Legend
(1) Lock
(2) Free

UNIT REPAIR (AW30–40LE) 7A4–103
18. Remove the sleeve(31) with the plungers(32)(33),
spring(34) and washer.
Remove the two plungers(32)(33) from the sleeve.
Remove the primary regulator valve(36) from the
valve body(37).
2 44R20 006 0
Inspection and Repair
1. Inspect strainer
Inspect strainer for residual adhesive and damage,
and clean and replace as necessary.
2 44R20 005 1
2. Inspect valve springs
Check for damage, squareness, rust and distorted
coils.
Measure the spring free length and replace if less
than shown below.
mm (in)
2 44R20 0077
SpringFree
lengthColor
(1) By-pass valve21.3
(0.839 )YELLOW
(2) Steel ball20.5
(0.807 )WHITE
(3) 1–2 shift valve 30.8
(1.213 )PURPLE
(4) Low coast modulator valve30.4
(1.197 )LIGHT
GREEN
(5) Accumulator control valve33.8
(1.331)—
(6) Solenoid modulator valve 26.6
(1.047)LIGHT
BLUE
(7) Cut back valve 34.0
(1.339)DARK
BLUE
(8) Primary regulator valve38.58
(1.519)WITHE