2004 ISUZU TF SERIES steering

SUPPLEMENTAL RESTRAINT SYSTEM 9A-47

Main Data and Specifications
Fastener Tightening Specification
Application N




m kg




m Ft.lb
SRS control unit 7 0.7 5
Steering wheel fixing bolt 35 3.5 25
Steering column (dash panel side fixing bolts) 20 2.0 14
Steering column (Pedal bracket fixing bolt) 20 2.0 14
Steering column (Universal joint fixing bolt) 31 3.2 23
Passenger Air Bag fixing bolt & nut 8 0.8 5.8
Pretensioner seat belt bolt 55 5.6 40

9A-50 SUPPLEMENTAL RESTRAINT SYSTEM

5-8840-2795-0 SRS Adapter for
Deployment Tool
901RW107
The 5-8840-2795-0 SRS Adapter for Deployment Tool
must be used with 5-8840-2468-0 SRS Deployment
Tool.

5-8521-0016-0 Steering Wheel remover
LNW28BSH003101

RESTRAINT CONTROL 9A1-13

Chart B “AIR BAG” warning lamp comes “ON” Steady

Step Action Yes No
1

1. When measurements are requested in this chart use 5-8840-
0285-0 DVM with correct terminal adapter from 5-8840-
0385-0.

2. Ignition switch “OFF.”

3. Connect scan tool to data link connector, follow directions as
given in the scan tool instruction MANUAL.

4. Ignition switch “ON.”

5. Request SRS diagnostic trouble code display.
Dose scan tool indicate “No Data Received”? Go to Step 2 Go to Step 3
2

1. Ignition switch “OFF”.

2. Inspect SRS control unit harness connector connection to
SRS control unit.
Is it securely connected to the SRS control unit? Ignition switch
“OFF.”
Replace SRS
control unit.
Go to Step 5 Connect SRS
control unit
securely to de–
activate shorting
clip in SRS control
unit harness
connector.
Go to Step 5
3 Using scan tool, request SRS data list.
Is “ignition” more than 9 volts? Go to Step 4 Ignition switch
“OFF.”
Replace SRS
control unit.
Go to Step 5
4

1. Ignition switch “OFF.”

2. Disconnect SRS coil and passenger air bag assemblies.
yellow connector located at base of steering column and
behind the glove box assembly.
Disconnect SRS control unit.

3. Disconnect the connector of “SRS Warning Lamp” of
instrument cluster.

4. Measure resistance from SRS control unit harness connector
terminal “40” to ground.
Does 5-8840-0285-0 DVM display “OL” (Infinite)? Go to Chart A Replace SRS
harness.
Go to Step 5
5 Reconnect all SRS components, ensure all components are
properly mounted.
Was this step finished? Repeat the “SRS
Diagnostic System
Check” Go to Step 5

RESTRAINT CONTROL 9A1-15

Chart C “AIR BAG” Warning Lamp Does Not Come “ON” Steady

Step Action Yes No
1

1. When measurements are requested in this chart, use 5-8840-
0285-0 DVM with correct terminal adapter from 5-8840-
0385-0.

2. Ignition switch “OFF.”
3. Remove and inspect “METER” fuse to the “AIR BAG”
warning lamp.
Is fuse good? Go to Step 2 Go to Step 7
2

1. Ignition switch “OFF.”

2. Disconnect SRS coil and passenger air bag assemblies.
Yellow connector located at base of steering column and
behind the glove box assembly.

3. Disconnect SRS control unit.

4. Ignition switch “ON.”
5. Measure voltage on SRS control unit harness connector from
terminal “39” to terminal “40” (ground).
Is system voltage present on terminal “39”? Go to Step 4 Go to Step 3
3

1. Ignition switch “OFF.”

2. Remove instrument meter cluster.
3. Check for proper connection to instrument cluster at SRS
warning lamp circuit terminal.

4. If ok, then remove and inspect “AIR BAG” bulb.
Is bulb good? Go to Step 5 Replace bulb.
Go to Step 6
4

1. Ignition switch “OFF.”

2. Disconnect instrument meter cluster harness connector.
3. Ignition switch “ON.”

4. Measure voltage on SRS control unit harness connector from
terminal “39” to terminal “40” (ground).
Is voltage 1 volt or less? Go to Chart A Replace SRS
harness.
Go to Step 6
5

1. Install bulb.

2. Measure resistance from instrument meter cluster harness
connector SRS warning lamp circuit terminal to SRS control
unit harness connector terminal “7”.
Is resistance 5.0 ohms or less? Service instrument
meter cluster.
Install instrument
meter cluster.
Go to Step 6 Replace SRS
harness.
Go to Step 6
6 Reconnect all SRS components, ensure all components are
properly mounted.
Was this step finished? Repeat the “SRS
Diagnostic System
Check” Go to Step 6
7 Perform chart C.
Was this step finished? Go to Step 8 Go to Step 1
8

1. Replace “METER” fuse.

2. Ignition switch “ON” wait 10 Seconds then ignition switch “Off.
“
3. Remove and inspect “METER” fuse.
Is fuse good? Install “METER”
fuse.
Go to Step 10 Go to Step 9

9A1-16 RESTRAINT CONTROL SYSTEM

Step Action Yes No
9

1. Disconnect SRS coil and passenger air bag assemblies.
Yellow connectors located at base of steering column and
behind the glove box assembly.

2. Disconnect SRS control unit.
3. Replace “METER” fuse.

4. Ignition switch “ON” wait 10 seconds.

5. Ignition switch “OFF”.
6. Remove and inspection “METER” fuse.
Is fuse good? Install “METER”
fuse.
Go to Chart A Replace SRS
harness.
Replace “METER”
fuse.
Go to Step 10
10 Reconnect all SRS components, ensure all components are
properly mounted.
Was this step finished? Repeat the “SRS
Diagnostic System
Check” Go to Step 10

9A1-18 RESTRAINT CONTROL SYSTEM

DTC Will Clear When
The ignition switch is turned “OFF.”

DTC Chart Test Description
Number(s) below refer to step number(s) on the
diagnostic chart:
2.
This test determines whether the malfunction is in
the SRS control unit.
3.
This test verifies connection of the yellow connector.
4.
This test cheeks for proper operation of the shorting
clip in the yellow connector.
5.
The test checks for a malfunction passenger air bag
assembly.
6.
This test determines whether the malfunctioning is
due to shortening in the wiring.
Diagnostic Aids
An intermittent condition is likely to be caused by a short
between circuits “Passenger Bag High” and “Passenger
Bag Low” or a malfunctioning shorting clip on the
passenger air bag assembly which would require
replacement of the air bag assembly. The test for this
diagnostic trouble code is only run while “AIR BAG”
warning lamp is performing the bulb check. When a
scan tool “Clear Codes” command is issued and the
malfunction is still present, the DTC will not reappear
until the next ignition cycle.


DTC B0016 (Flash Code 16) Passenger Airbag Squib Circuit Low Resistance

Step Action Yes No
1 Was the “SRS Diagnostic System Check” performed? Go to Step 2 Repeat the “SRS
Diagnostic System
Check”
2

1. Check the passenger air bag squib circuit for short to voltage
or short to ground.

2. If the problem found, repair as necessary.
Was a problem found? Verify repair Go to Step 3
3

1. Ignition switch “Off.”

2. Make sure the passenger air bag assembly yellow connector
located behind the glove box assembly is seated properly.
Is the yellow connector connected properly? Go to Step 4 Seat passenger air
bag assembly
yellow connector
properly.
Go to Step 7
4

1. Disconnect and inspect the passenger air bag assembly
yellow connector located behind the glove box assembly.

2. If ok, reconnect the passenger air bag assembly connector.

3. Ignition switch “ON.”
Is DTC B0016 Current? Go to Step 5 Go to Step 7
5

1. Ignition switch “Off.”

2. Disconnect SRS coil and passenger air bag assembly, yellow
connector located at the base of the steering column and
behind the glove box assembly.

3. Connect 5-8840-2421-0 SRS driver/passenger load tool and
appropriate adapters to SRS coil and passenger air bag
assembly harness connectors.

4. Ignition switch “ON.”
Is DTC B0016 current? Go to Step 6 Ignition switch
“Off.”
Replace the
passenger air bag
assembly.
Go to Step 7
6

1. Ignition switch “Off.”

2. There has been a decrease in the total circuit resistance of
the passenger inflator deployment loop
Replace SRS
harness.
Go to Step 7 Go to Chart A

RESTRAINT CONTROL 9A1-21

DTC Will Clear When
The ignition switch is turned “OFF.”

DTC Chart Test Description
Number(s) below refer to step number(s) on the
diagnostic chart:
2.
This test determines whether the malfunction is in
the SRS control unit.
3.
This test verifies proper connection of the yellow
connector.
4.
This test checks for proper contact and/or corrosion
of the yellow connector terminals.
5.
The test checks for a malfunctioning passenger ai
r
bag assembly.
6.
This test determines whether the malfunction is due
to high resistance in the wiring.
Diagnostic Aids
An intermittent condition is likely to be caused by a poor
connection at the passenger air bag assembly harness
connector terminals “1” and “2”, SRS control unit
terminal “48” and “47”, or a poor wire to terminal
connection in circuits “Passenger Bag High” and
“Passenger Bag Low”. This test for this diagnostic
trouble code is only run while the “AIR BAG” warning
lamp is performing the bulb check. When a scan tool
“Clear Codes” command is issued and the malfunction
is still present, the DTC will not reappear until the next
ignition cycle.


DTC B0017 (Flash Code 17) Passenger Airbag Squib Circuit High Resistance

Step Action Yes No
1 Was the “SRS Diagnostic System Check” Performed? Go to Step 2 Go to The “SRS
Diagnostic System
Check”
2

1. Check the passenger air bag squib circuit for open.

2. If the problem found, repair as necessary.
Was a problem found? Verify repair Go to Step 3
3

1. Ignition switch “Off.”

2. Make sure the passenger air bag assembly yellow connector
located behind the glove box assembly is seated properly.
Is the yellow connector connected properly? Go to Step 4 Seat passenger Air
Bag assembly
yellow connector
properly.
Go to Step 7
4

1. Disconnect and inspect the passenger air bag assembly
yellow connector located behind the glove box assembly.

2. If ok, reconnect the passenger air bag assembly connector.
3. Ignition switch “ON.”
Is DTC B0017 current? Go to Step 5 Go to Step 7
5

1. Ignition switch “Off.”

2. Disconnect SRS coil and passenger air bag assembly, yellow
connector located at the base of the steering column and
behind the glove box assembly.

3. Connect 5-8840-2421-0 SRS driver / passenger load tool and
appropriate adapters to SRS coil and passenger air bag
assembly harness connectors.

4. Ignition switch “ON.”
Is DTC B0017 Current? Go to Step 6 Ignition switch
“Off.”
Replace the
passenger air bag
assembly.
Go to Step 7

RESTRAINT CONTROL 9A1-27

DTC Will Set When
The combined resistance of the driver air bag
assembly, SRS Coil assembly, harness wiring circuits
“Driver Bag High” and “Driver Bag Low”, and connector
terminal contact is above a specified value. This test is
run once each ignition cycle during the “Resistance
Measurement Test” when:
1.
No “higher priority faults” are detected during “Turn–
ON”
2.
“Ignition 1” voltage is in the specified value.

Action Taken
SRS control unit turns “ON” the “AIR BAG” warning
lamp and sets DTC B0022.

DTC Will Clear When
The ignition switch is turned “OFF.”
DTC Chart Test Description
Number(s) below refer to circled number(s) on the
diagnostic chart:
2.
This test determines whether the malfunction is in
the SRS control unit.
3.
This test verifies proper connection of the yellow
connector at the base of the steering column.
4.
This test checks for proper operation of the shorting
clip in the yellow connector.
5.
This test isolate the malfunction to one side of the
SRS coil assembly yellow connector located at the
base of steering column.
6.
This test determines whether the malfunction is due
to shortening in the wiring.
7.
This test determines whether the malfunction is in
the SRS coil assembly or the driver air bag
assembly.

Diagnostic Aids
An intermittent condition is likely to be caused by a short
between circuit “Driver Bag High” or “Driver Bag Low”
or a malfunctioning shorting clip on the driver air bag
assembly or SRS coil assembly which would require
replacement of the component. The test for this
diagnostic trouble code is only run while the “AIR BAG”
warning lamp is performing the bulb check. When a
scan tool “Clear Codes” command is issued and the
malfunction is still present, the DTC will not reappear
until the next ignition cycle.


DTC B0022 (Flash Code 22) Driver Airbag Squib Circuit Low Resistance

Step Action Yes No
1 Perform the “SRS Diagnostic System Check.”
Was the “SRS Diagnostic System Check” performed? Go to Step 2 Go to the “SRS
Diagnostic System
Check”
2

1. Check the driver air bag squib circuit for short to voltage or
short to ground.

2. If the problem found, repair as necessary.
Was a problem found? Verify repair Go to Step 3
3

1. Ignition switch “OFF.”

2. Make sure the SRS coil assembly yellow connector located
at the base of steering column is seated properly.
Is the connector connected properly? Go to Step 4 Seat driver air bag
assembly
connector
properly.
Go to Step 8
4

1. Disconnect and inspect the SRS coil assembly yellow
connector located base of steering column.

2. If ok, reconnect the SRS coil assembly yellow connector.

3. Ignition switch “ON.”
Is DTC B0022 current? Go to Step 5 Go to Step 8