2004 ISUZU TF SERIES immobilizer

IMMOBILIZER SYSTEM 11A-21

Tech-2 Features
1.
Tech-2 is a 12volt system. Do not apply 24 volts.
2.
After connecting and/or installing the vehicle
communication interface (VCI) module, PCMCI
A
card and data link connector (DLC) to the Tech-2,
connect the tool to the vehicle DLC.
3.
Make sure the Tech-2 is OFF when removing o
r
installing the PCMCIA card.
4.
The Tech-2 has the capability of two or three
snapshots.
5.
The PCMCIA card is sensitive to magnetism and
static electricity, so care should be taken in the
handling of the card.
6.
The Tech-2 can not plot a graph when replaying a
snapshot.
7.
Always return to the Main Menu by pressing the
EXIT key several times before shutting down.
8.
To clear diagnostic trouble codes (DTCs), open
Application Menu and press "Clear DTC ".

Getting Started
Before operating the Isuzu PCMCIA card with the Tech
2, the following steps must be performed:
1.
The Isuzu System PCMCIA card inserts into the
Tech 2.
2.
Connect the SAE 16/19 adapter to the DLC cable.
3.
Connect the DLC cable to the Tech 2.
4.
Mark sure the vehicle ignition is off.
5.
Connect the Tech 2 SAE 16/19 adapter to the
vehicle DLC.


RHD (For example)
060R300015

6.
Tune on the vehicle ignition (key) switch.
7.
Power the Tech-2 ON and verify the Tech-2 powe
r
up display.

060RW009

11A-22 IMMOBILIZER SYSTEM

Operating Procedure
The power up screen is displayed when you power up
the tester with the Isuzu systems PCMCIA card.
Follow the operating procedure below.

060R100102

LTW3BALH000101

IMMOBILIZER SYSTEM 11A-23

Menu
The following table shows which functions are used for
the available equipment versions.









 



 

 !

" 
#


$

" $%


&





 ! 



##
'

"  

(


&  $
)*

+
## 


###
'





# $
)*

NOTE: Before going to programming process, Tech-2
indicates instruction as follows.

060R200289
DTC
On OBD has two options available in the Tech 2 DTC
mode to display the enhanced information available.


Read DTC Info Ordered By Priority


Read DTC Info As Stored By ECU
Clear DTC Information
To clear Diagnostic Trouble Codes (DTCs), use the
diagnostic scan tool "clear DTC information" function.
Tech-2 Data Display
Use the Tech 2 Data Values only after the On-Board
Diagnostic System Check has been completed, no
DTC(s) were noted, and you have determined that the
on-board diagnostics are functioning properly.
The Tech 2 data values represent values that would be
seen on a normally-immobilizer system.
Check Vehicle Identification Number (VIN)
1.
Select "Body" and "Immobilizer".
2.
Select "Additional Function" and "Read ECU
Identification".
3.
Shows up VIN on tech-2 display.
Reset Immobilizer (Reset Immobilizer
Control Unit)
1.
Select "Body" and "Immobilizer".
2.
Select "Additional Function" and "Reset
Immobilizer".
3.
Enter the security code and press Confirm.
4.
Reset Immobilizer screen shows up with warning.

See the following screen.

060R200279

11A-24 IMMOBILIZER SYSTEM

5.
When reset is completed, the following screen
shows up.

060R200278

Reset Engine Control Module (Reset ECM)
1.
Select "Body" and "Immobilizer".
2.
Select "Additional Function" and "Reset Engine
Control Module".
3.
The following screen shows up.

060R200289

4.
Confirm the following screen shows up.
5.
Input the security code, then press the soft key o
f
"Not Okay" or "Okay".
6.
The following screen shows up.


7.
Programming is completed.

060R200278

8.
When the procedure is completed waits 10
seconds and then turn the Key on.

The fail lamp begins to flash.
9.
Turn the ignition on, then engine dose not run.
10. Reset is completed.
Erase transponder key
1. Select "Body" and "Immobilizer".
2. Select "Additional Function” and "Erase
Transponder-Keys".
3. See immobilizer status on Tech-2 screen and type
security code. If the status dose not allow the
programming, only immobilizer status is displayed.
4. See illustration of caution.

IMMOBILIZER SYSTEM 11A-25






CAUTION


060R200286






Erase


060R200285

4.
See programming result on display.

Programming Immobilizer Function
Caution:

1)
Do not replace ICU and ECM at the same time
2)
Change ICU at first or ECM and other one
change follows.


1.
Select "Body" and "immobilizer".
2.
Select "Programming" on Tech-2 display.
3.
Check the display, then press the "Confirm" key.

LTW3BASH000401

4.
Install the "Hardware Key" on PC.
5.
Connect RS232 cable to the PC and Tech2.
6.
Turn on the PC, then start software "TIS 2000".
7.
Select "Security Access" in the TIS 2000 screen.

11A-26 IMMOBILIZER SYSTEM

8.
Select "Next" in the TIS 2000 screen and wait a
few seconds.
9.
When programming is enabled (Approved), then
press "close" in the TIS 2000 screen.

(Finish the "TIS 2000" operation.)
10.
Select "Program Immobiliser Function" on Tech-2
display.
11.
The following screen shows up.

060R200289

12.
Confirm the following screen shows up.
13.
Input the security code, then press the soft key o
f
"Not Okay" or "Okay".
14.
Select the engine type then, press "Enter" key.
15.
Input a program option, by moving the cursor on
the selection, then press "Enter" key.


Programming ICU


Programming ECM


Programming ICU and ECM




Programming ICU and ECM

060R200283
Programming ICU
1.
Follow Programming Immobilizer Function steps 1
through 14.
2.
Input a program option, by moving the cursor on
the selection, then pres "Enter" key.

060R200283

3.
Enter the security code.

IMMOBILIZER SYSTEM 11A-27

4.
Input the security code, then press the soft key of
"Okay" or "Not Okay".

060R200284

5.
Enter VIN.
6.
Enter Mechanical key number.
7.
Turn ON ignition.
8.
Select an engine system.
9.
See the programming result.

Tech-2 displays the result of programming as the
following.

Follow those instructions

Selected Programming is not possible due to
wrong System Status!


Immobilizer Not Programmed!


Immobilizer Already Programmed!


ECM Not Programmed!


ECM Already Programmed!
10.
Transponder key must be reprogrammed,
because all transponder information is erased.

When ICU is programmed. See Transponde
r
programming.

Programming ECM
1.
Follow Programming Immobilizer Function steps 1
through 14.
2.
Input a program option, by moving the cursor on
the selection, then pres "Enter" key.

060R200283
3.
Enter the security code.
4.
Input the security code, then press the soft key o
f
"Okay" or "Not Okay".

060R200284

5.
Turn on the Ignition.
6.
Select an Engine system.

11A-28 IMMOBILIZER SYSTEM

7.
See the display of programming result.

Tech-2 displays the result of programming as the
following.

Follow those instructions


Selected Programming is not possible due to
wrong System Status!


Immobilizer Not Programmed!


Immobilizer Already Programmed!

ECM Not Programmed!

ECM Already Programmed!
8.
Transponder key must be reprogrammed,
because all transponder information is erased.

When ICU is programmed. See Transponde
r
programming.
Programming ICU and ECM
1.
Follow Programming Immobilizer Function steps 1
through 14.
2.
Input a program option, by moving the cursor on
the selection, then pres "Enter" key.

060R200283
3.
Enter the security code.





4.
Input the security code, then press the soft key o
f
"Okay" or "Not Okay".

060R200284

5.
Input the security code.
6.
Enter VIN.
7.
Enter Key No.
8.
Select an engine system.

See programming result display and follow
instructions of the display.
9.
Transponder key must be reprogrammed,
because all transponder information on ICU is
erased when ICU is programmed. See
Transponder programming.
10.
Follow Programming ECM steps 2 through 8.
Transponder program
1.
Select "Body" and "Immobilizer".
2.
Select "Programming" and "Program Transponder-
Keys".

(Follow Programming Immobilizer Function steps 1
through 14.)
3.
See immobilizer status on Tech-2 screen, and
enter security code. If the status does not allow the
programming, only immobilizer status is displayed.