2004 ISUZU TF SERIES wiring

SUPPLEMENTAL RESTRAINT SYSTEM 9A-41

7. Remove the driver knee bolster assembly.


RTW49JSH000401
Legend
(1) RHD
(2) LHD

8. Remove the steering column cover.
9. Disconnect the wiring harness connectors located
at the base of steering column.
CAUTION: Never apply force to the steering wheel
in direction of the shaft by using a hammer o
r
other impact tools in an attempt to remove the
steering wheel. The steering shaft is designed as
an energy absorbing unit.
10. Remove the combination switch assembly with
SRS coil.
SRS coil is a part of combination switch assembly,
which cannot be replaced separately. Therefore, be
sure not to remove the SRS coil from the combination
switch assembly.
11.Remove the snap ring.
12. Remove the cushion rubber.
13. Disconnect shift lock cable (A/T only).
14.Disconnect the starter switch harness connecto
r
located base of steering column.
15. Remove steering lock cylinder assembly.



16.Apply a setting mark across the universal joint and
steering shaft to reassemble the parts in thei
r
original position.
060R300038
17.Remove steering column assembly.

Installation
1. Install the steering column assembly and align the
setting marks on the universal joint and steering
shaft made during removal.
060R300038
2. Tighten the steering column fixing bolts (dash
panel side) to the specified torque.
Torque: 20 N




m (2.0 kg




m/14 lb ft)
3. Tighten the steering column fixing bolts (Pedal
bracket) to the specified torque.
Torque: 20 N





m (2.0 kg





m/14 lb ft)

9A-42 SUPPLEMENTAL RESTRAINT SYSTEM

4. Tighten the universal joint to the specified torque.
Torque: 31 N




m (3.2 kg




m/23 lb ft)
5. Install steering lock cylinder assembly.
6. Connect shift lock cable (For A/T)
7. Install cushion rubber.
8. Install snap ring.
9. Install the combination switch assembly with SRS
coil.
10. Connect the wiring harness connector located on
the base of steering column.
11. Turn the SRS coil counterclockwise to full, return
about 3 turns and align the neutral mark.
CAUTION: When turning the SRS coil
counterclockwise to full, stop turning if resistance
is felt. Forced further turning may damage to the
cable in the SRS coil.
826RW014
Legend
(1) Neutral mark

12.Install steering column cover.
CAUTION: When installing the steering column
cover, be sure to wire (through each harness) as
illustrated so that the harness starter switch,
combination switch and SRS coil may not catch
wiring.


825RS048
13.Install the steering wheel and align the setting
marks.

9A-46 SUPPLEMENTAL RESTRAINT SYSTEM

Pretensioner Seat Belt (If so quipped)
Service Precaution
WARNING: WHEN PERFORMING SERVICE ON OR
AROUND THE PRETENSIONER SEAT BELT O
R
THE PRETENSIONER SEAT BELT WIRING,
FOLLOW THE PROCEDURES LISTED BELOW TO
TEMPORARILY DISABLE THE PRETENSIONE
R
SEAT BELT.
FAILURE TO FOLLOW PROCEDURES COULD
RESULT IN POSSIBLE THE PRETENSIONER SEAT
BELT DEPLOYMENT, PERSONAL INJURY O
R
OTHERWISE UNNEEDED THE PRETENSIONE
R
SEAT BELT REPAIR.
AS A PRECAUTION, WEAR GLOVES AND SAFETY
GLASSES WHEN PERFORMING THE
PRETENSIONER SEAT BELT. WHEN DEPLOY A
LIVE PRETENSIONER SEAT BELT AT OUTSIDE
THE VEHICLE, DEPLOYMENT HARNESS SHALL
REMAIN SHORTED AND NOT BE CONNECTED TO
A POWER SOURCE UNTIL THE PRETENSIONE
R
SEAT BELT IS TO BE DEPLOYED. THE
PRETENSIONER SEAT BELT WILL IMMEDIATELY
DEPLOY WHEN A POWER SOURCE IS
CONNECTED TO IT. CONNECTING THE
DEPLOYMENT HARNESS SHOULED ALWAYS BE
THE FINAL STEP IN THE PRETENSIONER SEAT
BELT DEPLOYMENT PROCEDURE. FAILURE TO
FOLLOW PROCEDURES IN THE ORDER LISTED
COULD RESULT IN PERSONAL INJURY.
Parts Location


RTW49JSH000301
Legend
(1) Seat
(2) Bolt
(3) Pretensioner Harness
(4) Pretensioner

Removal
1. Turn ignition switch to “LOCK”, remove key.
2. Remove the foot rest located behind the seat.
3. Remove the cover on seat slide.
4. Disconnect the pretensioner connector at the
base of the seat.
5. Remove four fixing bolts the seat slide and
remove seat.
6. Remove the seat cover.
7. Remove the pretensioner seat belt assembly.
Installation
1. Install the pretensioner seat belt assembly.
2. Install the seat cover.
3. Install the seat on seat slide and four fixing bolts.
4. Connect the yellow pretensioner connector at the
base of the seat.
5. Install the cover on seat slide.
6. Install the foot rest located behind the seat.

9A-48 SUPPLEMENTAL RESTRAINT SYSTEM

Special Tools
WARNING: TO AVOID DEPLOYMENT WHEN
TROUBLESHOOTING THE SRS, DO NOT USE
ELECTRICAL TEST EQUIPMENT SUCH AS A
BATTERY–POWERED OR AC–POWERED
VOLTMETER, OHMMETER, ETC., OR ANY TYPE
OF ELECTRICAL EQUIPMENT OTHER THAN THAT
SPECIFIED IN THIS MANUAL. DO NOT USE A
NONPOWERED PROBE–TYPE TESTER.
INSTRUCTIONS IN THIS MANUAL MUST BE
FOLLOWED CAREFULLY, OTHERWISE
PERSONAL INJURY MAY RESULT.

5-8840-2421-0 SRS Driver/Passenger Load
Tool
901RS146
The SRS Driver/Passenger Load Tool 5-8840-2421-0
is used only when called for in this section. It is used
as a diagnostic aid and safety device to prevent
inadvertent air bag assembly deployment.
The load tool has three yellow connectors attached to
its case.
The three small connectors are electrically functional
and serve as resistive load substitutions.
No more than two connectors are used at any time.
One of the small connectors is used to substitute for
the load of the driver air bag assembly when it is
connected at the top of the column to the SRS coil
assembly. Another small connector is used to
substitute for the load of the driver air bag assembly
and the SRS coil assembly when it is connected at the
base of the column to the SRS wiring harness. The
third small connector is used to substitute for the load
of the passenger air bag assembly when connected to
the passenger air bag assembly harness connector.
By substituting the resistance of the load tool when
called for, a determination can be made as to whether
an inflator circuit component is causing system
malfunction and which component is causing the
malfunction. The load tool should be used only when
specifically called for in the diagnostic procedures.

5-8840-0285-0 DVM
901RS163
The 5-8840-0285-0 DVM is the preferred DVM for use
in SRS diagnosis and repair. However, 5-8840-0366-
0 may be used if 5-8840-0285-0 is not available. No
other DVMs are approved for SRS diagnosis and
repair.

Scan Tool
901RW176

9A1-2 RESTRAINT CONTROL SYSTEM

DTC B0051 (Flash Code 51) Squib Circuit Activated (Clash) .........................................9A1-37
DTC B0053 (Flash Code 53) Deployment Command Despite Present Trouble
Code ..................................................................................................................................9A1-39
DTC B0057 (Flash Code 57) Passenger Pretensioner Squib Circuit Low
Resistance ........................................................................................................................9A1-41
DTC B0058 (Flash Code 58) Passenger Pretensioner Squib Circuit High
Resistance ........................................................................................................................9A1-44
DTC B0059 (Flash Code 59) Passenger Pretensioner Squib Circuit Voltage
Range/Performance .........................................................................................................9A1-47
DTC B0064 (Flash Code 64) Driver Pretensioner Squib Circuit Low Resistance .........9A1-50
DTC B0065 (Flash Code 65) Driver Pretensioner Squib Circuit High Resistance ........9A1-53
DTC B0066 (Flash Code 66) Driver Pretensioner Squib Circuit Voltage Range/
Performance .....................................................................................................................9A1-56
DTC B0670 (Flash Code 63) Airbag Telltale Circuit Malfunction ...................................9A1-59
DTC B1000 (Flash Code 72) SDM Internal Fault ..............................................................9A1-61


Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE
SRS COMPONENTS OR THE SRS WIRING, REFER
TO THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN
POSSIBLE AIR BAG DEPLOYMENT, PERSONAL
INJURY, OR OTHERWISE UNNEEDED SRS SYSTEM
REPAIRS.

CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or
other corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener.
When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.

9A1-4 RESTRAINT CONTROL SYSTEM

cautions in the service manual and on warning labels
attached to SRS components.

Basic Electrical Circuits
You should understand the basic theory of electricity
including series and parallel circuits, and understand
the voltage drops across series resistors. You should
know the meaning of voltage (volts), current (amps),
and resistance (ohms). You should understand what
happens in a circuit with an open or a shorted wire. You
should be able to read and understand a wiring
diagram.

“Flash Code” Diagnostics
Flash code diagnostics can be used to read active
codes and to determine if history codes are present but
cannot be used to clear codes or read history codes.
Flash code diagnostics is enabled by grounding by
terminal 4 shorting to terminal 13 of the DLC connector
with the ignition switch “ON”. Grounding terminal 4 of
the DLC connector pulls the “Diagnostics Request”
input (Terminal 1) of the SRS control unit low and
signals the SRS control unit to enter the flash code
diagnostic display mode.


060R300052

9A1-14 RESTRAINT CONTROL SYSTEM

Chart C “AIR BAG” Warning Lamp Does Not Come “ON” Steady


RTW49JLF000101

Circuit Description
When the ignition switch is first turned “ON”, “Ignition 1”
voltage is applied from the “METER” fuse to the “AIR
BAG” warning lamp which is connected to “SRS
Warning Lamp”, terminal “39”. The “SRS” fuse appl
y
system voltage to the “Ignition 1” inputs, terminals “35”.
The SRS control unit responds by flashing the “AIR
BAG” warning lamp seven times. If “Ignition 1” is more
than 16 volts, the “AIR BAG” warning lamp will be still
“OFF” solid with no DTCs set.

Chart Test Description
Number(s) below refer to step number(s) on the
diagnostic chart:
1.
This test decides whether power is available to SRS
control unit warning lamp power feed circuit.
2.
This test determines whether the voltage is present
in the warning lamp circuit.
3.
This test determines if the malfunction is in the
instrument cluster.
4.
This test checks for open in the warning lamp
circuitry.
5.
This test isolates the SRS warning lamp circuit and
checks for a short in the SRS warning lamp circuit to
B+.
8.
This test checks for a short from the SRS control
unit warning lamp power feed circuit to ground.
9.
This test determines whether the short to ground is
due to a short in the wiring.

RESTRAINT CONTROL 9A1-17

DTC B0016 (Flash Code 16) Passenger Airbag Squib Circuit Low Resistance


RTW49JLF000101
Circuit Description
When the ignition switch is turned “ON”, the SRS
control unit will perform tests to diagnose critical
malfunctions within itself. Upon passing these tests
“Ignition 1”, and deployment loop voltages are
measured to ensure they are within their respective
normal voltage ranges. The SRS control unit then
proceeds with the “Resistance Measurement Test”.
“Passenger Bag Low” terminal “47” is grounded through
a resistor and the passenger current source connected
to “Passenger Bag High” terminal “48” allows a known
amount of current to flow. By monitoring the voltage
difference between “Passenger Bag High” and
“Passenger Bag Low”, the SRS control unit calculates
the combined resistance of the passenger air bag
assembly, harness wiring circuits “Passenger Bag High”
and “Passenger Bag Low” connector terminal contact.
DTC Will Set When
The combined resistance of the passenger air bag
assembly, harness wiring circuits “Passsenger Bag
High” and “Passenger Bag Low”, and connector
terminal contact is above a specified value. This test
is run once each ignition cycle during the “Resistance
Measurement Test” when:
1.
No “higher priority faults” are detected during “Turn–
ON”,
2.
“Ignition 1” voltage is in the specified value.

Action Taken
SRS control unit turns “ON” the “AIR BAG” warning
lamp and sets a diagnostic trouble code.