2004 ISUZU TF SERIES immobilizer

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-333
Step Action Value (s) Yes No
17
1. Review all diagnostic procedures within this table.
2. If all procedures have been completed and no
malfunctions have been found, review/inspect the
following:

Visual/physical inspection.

Tech 2 data.

All electrical connections within a suspected circuit
and/or system.
Was a problem found?
- Verify repair Go to Step 18
18
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 19
19
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

6E-336 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No
17
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

6E-340 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No
22
Check the ECM grounds to verify that they are clean
and tight. Refer to the ECM wiring diagrams.
Was a problem found?
- Verify repair Go to Step 23
23
1. Check for faulty engine mounts.
2. If a problem is found, repair as necessary.
Was a problem found?
- Verify repair Go to Step 24
24
Check for the following engine mechanical problems
(refer to Engine Mechanical section):

Low compression.

Leaking cylinder head gaskets.

Worn camshaft.

Sticking or leaking valves. -Valve timing.

Broken valve springs.

Camshaft drive belt slipped or stripped.
Was a problem found?
- Verify repair Go to Step 25
25
1. Review all diagnostic procedures within this table.
2. If all procedures have been completed and no
malfunctions have been found, review/inspect the
following:

Visual/physical inspection.

Tech 2 data.

All electrical connections within a suspected circuit
and/or system.
Was a problem found?
- Verify repair Go to Step 26
26
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 27
27
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

6E-344 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No
22
1. Review all diagnostic procedures within this table.
2. If all procedures have been completed and no
malfunctions have been found, review/inspect the
following:

Visual/physical inspection.

Tech 2 data.

All electrical connections within a suspected circuit
and/or system.
Was a problem found?
- Verify repair Go to Step 23
23
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 24
24
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

6E-348 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No
22
1. Review all diagnostic procedures within this table.
2. If all procedures have been completed and no
malfunctions have been found, review/inspect the
following:

Visual/physical inspection.

Tech 2 data.

All electrical connections within a suspected circuit
and/or system.
Was a problem found?
- Verify repair Go to Step 23
23
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 24
24
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-351
Step Action Value (s) Yes No
17
Check for the following engine mechanical problems
(refer to Engine Mechanical Section):

Low compression. -Leaking cylinder head gaskets.

Worn camshaft. -Sticking or leaking valves.

Valve timing. -Broken valve springs.

Camshaft drive belt slipped or stripped.
Was a problem found?
- Verify repair Go to Step 18
18
1. Check for faulty engine mounts.
2. If a problem is found, repair as necessary.
Was a problem found?
- Verify repair Go to Step 19
19
1. Review all diagnostic procedures within this table.
2. If all procedures have been completed and no
malfunctions have been found, review/inspect the
following:

Visual/physical inspection.

Tech 2 data.

All electrical connections within a suspected circuit
and/or system.
Was a problem found?
- Verify repair Go to Step 20
20
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 21
21
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-355
Step Action Value (s) Yes No
24
Is the ECM programmed with the latest software release?
If not, download the latest software to the ECM using the
"SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 25
25
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be programmed.
Refer to section of the Service Programming System (SPS) in
this manual. Following ECM programming, the immobilizer
system (if equipped) must be linked to the ECM. Refer to
section 11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

6E-358 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No
12
Check the fuel pressure. Refer to Fuel System
Diagnosis.
Was a problem found?
- Verify repair Go to Step 13
13
Monitor "B1S1 (Bank 1 Sensor 1) Status" and "B2S1
(Bank 2 Sensor 1) Status" on the Tech 2.
Is the "B1S1 (Bank 1 Sensor 1) Status" or "B2S1
(Bank 2 Sensor 1) Status" in the lean condition?
- Go to Step 14 Go to Step 15
14
Check items that can cause the engine to run lean.
Refer to DTC P0171 "O2 Sensor System Too Lean
(Bank 1)" or DTC P0174 "O2 Sensor System Tool
Lean (Bank 2)".
Was a problem found?
- Verify repair Go to Step 15
15
Check spark plugs for proper heat range.
Were incorrect spark plugs installed?
- Verify repair Go to Step 16
16
1. Remove excessive carbon buildup with a top
engine cleaner.
2. Re-evaluate vehicle performance.
Is detonation still present?
- Verify repair Go to Step 17
17
Check for an engine mechanical problem. Perform a
cylinder compression check. Refer to Engine
Mechanical.
Was a problem found?
- Verify repair Go to Step 18
18
1. Review all diagnostic procedures within this table.
2. If all procedures have been completed and no
malfunctions have been found, review/inspect the
following:

Visual/physical inspection.

Tech 2 data.

All electrical connections within a suspected circuit
and/or system.
Was a problem found?
- Verify repair Go to Step 19
19
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 20
20
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -