2004 ISUZU TF SERIES section 8A

ENGINE MECHANICAL 6A – 117


RTW46ASH001201
33. Injection Nozzle Holder
1. Install the injection nozzle gasket and the O-ring to the
injection nozzle holder.
Be sure that the O-ring fits snugly in the injection
nozzle groove.
2. Install the nozzle holder toghther with the nozzle holder
bracket to the cylinder head.










3. Tighten the nozzle holder bracket bolt to the specified
torque.


Injection Nozzle Holder Bracket Bolt
Torque N·m(kg·m/lbft)
37 (3.8/28)













Note on Valve Clearance Adjustment
Valve clearances must be adjusted before the cylinder
head cover is reinstalled.Refer to "Valve Clearance
Adjustment" in the "Servicing" Section of this manual.


Valve Clearance (At Cold) mm(in)
0.4 (0.0157)


RTW46ASH001101















34. Cylinder Head Cover
1. Apply engine oil to the rocker arm and the valve spring.
2. Install the cylinder head cover gasket to the head
cover. Check to see that the head cover gasket has no
loose areas.
3. Tighten the cylinder head cover nuts in the numerical
order shown in the illustration.


Cylinder Head Cover Bolt Torque N·m(kg·m/lbft)
13 (1.3/9.4)
4. Connect the positive crankcase ventilation (PCV) hose
to the cylinder head cover.




014RY00015

ENGINE MECHANICAL 6A – 123




15. Starter Motor
Tighten the starter motor bolts to the specified torque.
Starter Motor Bolt Torque N·m(kg·m/Ib ft)
85 (8.7/63)

16. Injection Pump
17. Injection Pump Cover (4JA1TC/4JH1TC only)


18. Engine Foot
Install the engine foot to the cylinder body and tighten the
bracket bolts to the specified torque.
Engine Foot Bolt Torque N·m(kg·m/Ib ft)
Right Side M10
1.25
40 (4.1/30)
M10
1.25
40 (4.1/30) Left Side
M14
1.50
127 (13/93)









4JA1L, 4JH1TC
022R300003
















4JA1TC
RTW46ASH002601







RTW36ASH001001
















19. Intake Manifold
1) Install the manifold gasket to the intake manifold.
2) Connect the intake rubber hose to the intake duct.
3) Tighten the intake manifold bolts and the flange nuts
to the specified torque.
Intake Manifold Bolt Torque N·m(kg·m/Ib ft)
19 (1.9/14)

Intake Manifold Flange Nut Torque N·m(kg·m/Ib ft)
24 (2.4/18)

4) Connect the PCV hose to the cylinder head cover.

5) Install the fan drive belt and adjust the belt tension
referring SERVICING of this section

6A – 136 ENGINE MECHANICAL





RTW36ASH000601
Removal
1. Radiator Grille

Refer to removal procedure in Sheet Metal section.







RTW36ASH000501
2. Front Bumper Fascia

Remove the nine clips and four screws.

Disconnect the fog light harness connectors.
















RTW46ASH002101
3. Front Bumper Impact Support Assembly

Remove the nut and two bolts.



4. Inter Cooler

Remove the nut and two bolts.

Disconnect the air hose.




Installation
4. Inter Cooler

Tighten the nut and two bolts.


3. Front Bumper Impact Support Assembly

Tighten the nut and two bolts.



2. Front Bumper Fascia

Install the nine clips and four screws.

Connect the fog light harness connectors.


1. Radiator grille

Refer to installation procedure in Sheet Metal section.

ENGINE COOLING 6B – 1


SECTION 6B
ENGINE COOLING


TABLE OF CONTENTS
PAGE
Main Data and Specifications ....................................................................................... 6B - 3
General Description .................................................................................................. 6B - 4
Coolant Flow .............................................................................................................. 6B - 4
Water Pump................................................................................................................ 6B - 5
Thermostat ................................................................................................................. 6B - 5
Radiator ...................................................................................................................... 6B - 6
Diagnosis........................................................................................................................ 6B - 7
Draining and Refilling Cooling System ........................................................................ 6B - 8
Water Pump .................................................................................................................... 6B - 10
Removal and Installation .......................................................................................... 6B - 10
Removal...................................................................................................................... 6B - 10
Inspection and Repair ............................................................................................... 6B - 11
Installation.................................................................................................................. 6B - 11
Thermostat ..................................................................................................................... 6B - 13
Removal and Installation .......................................................................................... 6B - 13
Removal...................................................................................................................... 6B - 13
Inspection and Repair ............................................................................................... 6B - 13
Installation.................................................................................................................. 6B - 14
Radiator .......................................................................................................................... 6B - 15
Removal and Installation .......................................................................................... 6B - 15
Radiator and Associated Parts................................................................................. 6B - 15
Removal...................................................................................................................... 6B - 16
Inspection and Repair ............................................................................................... 6B - 17
Installation.................................................................................................................. 6B - 18

6B – 6 ENGINE COOLING



110RS001
RADIATOR
The radiator is a tube type with corrugated fins. In order to
raise the boiling point of the coolant, the radiator is fitted with a
cap in which the valve is operated at 93.3

122.7 kPa (13.5

17.8 psi) pressure. (No oil cooler provided for M/T)





F06RW005
Antifreeze Solution
NOTE: Antifreeze solution + Water = Total cooling system
capacity.
Total Cooling System Capacity Lit (US / UK gal)
9.4 (2.5/21) 4JA1L/TC
M/T 10.1 (2.7/2.2) 4JH1TC
A/T 10.0 (2.6/2.2) 4JH1TC
See section 0B MAINTENACE AND LUBRICATION.





PTW46BSH000201
NOITE:
To maintain the corrosion resistance of the aluminum
radiator, water and antifreeze must be combined in a 1:1
solution (50% antifreeze and 50% water)
NOTE

6B – 10 ENGINE COOLING

WATER PUMP
REMOVAL AND INSTALLATION
Read this Section carefully before performing any removal and installation procedure. This Section gives you
important points as well as the order of operation. Be sure that you understand everything in this Section before you
begin.




Removal
1. Radiator Upper Hose
1) Partially drain the engine coolant.
2) Remove the radiator upper hose.





031R300003
2. Water Outlet Pipe
1) Disconnect the turbocharger-cooling pipe from outlet pipe.
2) Loosen the fixing bolt and remove the water outlet bolt.
3. Thermostat
Remove the thermostat from the thermostat housing.
Take care not to damage the thermostat.
4. Upper Fan Shroud

5. Fan and Fan Clutch 1) Loosen the fan clutch nuts.
2) Remove the fan together with the fan clutch. Take care not to damage the radiator core.
6. Fan Drive Belt and Pulley
1) Loosen the tension adjust bolt on the generator.
2) Remove the fan drive belt with the fan pulley.

030R300001 7. Water Pump
1) Remove the water pump bolts.
2) Remove the water pump.

030R300002

ENGINE COOLING 6B – 13
THERMOSTAT
REMOVAL AND INSTALLATION
Read this Section carefully before performing any removal and installation procedure. This Section gives you
important points as well as the order of operation. Be sure that you understand everything in this Section before you
begin.

Removal
1. Radiator Upper Hose
1) Partially drain the engine coolant.
2) Remove the radiator upper hose.


2. Water Outlet Pipe 3) Disconnect the turbocharger-cooling pipe from outlet pipe.
4) Loosen the fixing bolt and remove the water outlet bolt.
3. Thermostat
Remove the thermostat from the thermostat housing.
Take care not to damage the thermostat.

031R300003

Inspection and Repair
Make the necessary adjustments, repairs, and part
replacements if excessive wear or damage is discovered
during inspection.


031RY00005
Operating Test of Thermostat
1. Completely submerge the thermostat in water.
2. Heat the water. Stir the water constantly to avoid direct heat being
applied to the thermostat.
3. Check the thermostat initial opening temperature.
Thermostat Initial Opening Temperature
C (
F)
82 (180)

4. Check the thermostat full opening temperature.
Thermostat Full Opening Temperature
C (
F)
95 (203)

Valve Lift At Fully Open Position mm (in)
9.5 (0.37)

FUEL SYSTEM 6C – 1


SECTION 6C
FUEL SYSTEM


TABLE OF CONTENTS
PAGE
Main Data and Specifications ....................................................................................... 6C - 3
General Description....................................................................................................... 6C - 4
Fuel Flow .................................................................................................................... 6C - 4
Fuel Filter and Water Separator ............................................................................... 6C - 5
Injection Pump ........................................................................................................... 6C - 7
Injection Nozzle ......................................................................................................... 6C - 8
Fuel Tank ........................................................................................................................ 6C - 9
Removal ..................................................................................................................... 6C - 9
Installation ................................................................................................................. 6C - 10
Fuel Pump ...................................................................................................................... 6C - 12
Removal...................................................................................................................... 6C - 13
Installation.................................................................................................................. 6C - 13
Fuel Tube / Quick - Connector Fittings ........................................................................ 6C - 14
Filler Neck ...................................................................................................................... 6C - 16
Removal...................................................................................................................... 6C - 16
Installation.................................................................................................................. 6C - 16
Fuel Filler Cap ................................................................................................................ 6C - 17
Injection Pump ............................................................................................................... 6C - 18
Removal and Installation .......................................................................................... 6C - 18
Removal...................................................................................................................... 6C - 18
Installation.................................................................................................................. 6C - 21