2004 ISUZU TF SERIES brake sensor

7A2-12 DIAGNOSIS (JR405E)
F0: Diagnostic Trouble Code
F0: Read DTC Infor As Stored By ECU
F1: Clear DTC Information
F1: Data Display
F2: Snapshot
F3: Miscellaneous Test
F0: Lamp
F0: Power Lamp Test
F1: 3rd Start Lamp Test
F2: AT Oil Temperature Lamp Test
F3: Transmission Check Light Test
F1: Solenoids
F0: Low & Reverse Brake Solenoid
F1: 2-4 Brake Solenoid
F2: High Clutch Solenoid
F3: Low Clutch Solenoid
F4: Line Pressure Solenoid
F5: Lock Up Duty Solenoid
F4: Programming
F0: Program VIN
F1: Lock ECU

F0: Diagnostic Trouble Code
The purpose of the "Diagnostic Trouble Codes" mode is to
display stored trouble code in the TCM.
When "Clear DTC Information" is selected, a "Clear DTC
Information", warning screen appears. This screen informs you
that by cleaning DTC's "all stored DTC information in the TCM
will be erased".
After clearing codes, confirm system operation by test driving
the vehicle.

F1: Data Display
The purpose of the "Data Display" mode is to continuously
monitor data parameters.
The current actual values of all important sensors and signals
in the system are display through F1mode.
See the "Typical Scan Data" section.

F2: Snapshot
"Snapshot" allows you to focus on making the condition occur,
rather than trying to view all of the data in anticipation of the
fault. The snapshot will collect parameter information around a
trigger point that you select.

F3: Miscellaneous Test:
The purpose of "Miscellaneous Test" mode is to check for
correct operation of electronic system actuators.

F4: Programming (Factory Use Only):
The purpose of "Programming" is to program VIN in the ECM
and lock the programmed data.

DIAGNOSIS (JR405E) 7A2-33
DIAGNOSIS TROUBLE CODE TABLE

Flash Code
(P-Code)

CHECK TRANS Flash Pattern

Description
CHECK
TRANS
Warning

11 (P0722) Vehicle Speed Sensor No Signal ON


12 (-) Normal -


13 (P0727) ON

Engine Revolution Sensor No
Signal

14 (P0717) Turbine Speed Sensor No Signal ON


15 (P0710) ATF Temperature Sensor FailureOFF


16 (P0560) System Voltage Failure ON


17 (P0705) Inhibitor Switch Failure ON


22 (P1120) Throttle Signal Failure ON


25 (P1875) GND Return Circuit Failure ON


26 (P1853) ON

Low & Reverse Brake Pressure
Switch Failure

27 (P1858) 2-4 Brake Pressure Switch FailureON


28 (P1863) ON

High Clutch Pressure Switch
Failure

31 (P0753) ON

Low & Reverse Brake Duty
Solenoid Failure

32 (P0758) 2-4BrakeDutySolenoidFailure ON


33 (P0763) ON
High Clutch Duty Solenoid Failure

DIAGNOSIS (JR405E) 7A2-35
FAIL-SAFEFUNCTION
Fail-Safe Condition
Flash Code
(P-Code)

Description
CHECK
TRANS
Warning

Gear Shift
Solenoid
Line
Pressure
Solenoid

Lock-up

Remark
11
(P0722)
Vehicle peed Sensor No
Signal ON 3rdFix All Stop - Inhibited
13
(P0727)
Engine Revolution Sensor
No Signal ON - - - Inhibited
14
(P0717)
Turbine Speed Sensor No
Signal ON 3rdFix All Stop - Inhibited
15
(P0710)
ATF Temperature Sensor
Failure OFF 3,2,L - - Inhibited*1
16
(P0560)
System Voltage Failure ON 3rdFix All Stop - Inhibited*2
17
(P0705)
Inhibitor Switch Failure ON 3rdFix All Stop - Inhibited
22
(P1120)
Throttle Signal Failure ON 3rdFix All Stop - Inhibited
25
(P1875)
GND Return Circuit
Failure ON 3rdFix All Stop - Inhibited*2
26
(P1853)
Low & Reverse Brake
Pressure Switch Failure ON No Fail-safe Function
27
(P1858)
2-4 Brake Pressure
Switch Failure ON No Fail-safe Function
28
(P1863)
High Clutch Pressure
Switch Failure ON No Fail-safe Function
31
(P0753)
Low & Reverse Brake
Duty Solenoid Failure ON 3rdFix All Stop - Inhibited
32
(P0758)
2-4 Brake Duty Solenoid
Failure ON 3rdFix All Stop - Inhibited
33
(P0763)
High Clutch Duty Solenoid
Failure ON 3rdFix All Stop - Inhibited
34
(P0768)
Low Clutch Duty Solenoid
Failure ON 3rdFix All Stop - Inhibited
35
(P0748)
Line Pressure Solenoid
Failure ON - - Stop -
36
(P1860)
Lock-up Duty Solenoid
Failure ON - - - Inhibited
41
(P0731)
1stGearRatioError ON No Fail-safe Function
42
(P0732)
2ndGearRatioError ON No Fail-safe Function
43
(P0733)
3rdGearRatioError ON No Fail-safe Function
44
(P0734)
4thGearRatioError ON No Fail-safe Function
51
(P1750)
Low & Reverse Brake
Fail-safe Valve Failure ON 3rdFix All Stop - Inhibited
52
(P1755)
2-4 Brake Fail-safe Valve
Failure ON 3rdFix All Stop - Inhibited
-
(P0602)
ECU Programming Error ON No Fail-safe Function
*1: When the engine speed is more than 470 rpm for 10 minuets, the lock-up and gear shift to 4th (over-drive) are
allowed.
*2: In case of fail-safe valve failure, gear shift to 4th (over-drive) is inhibited.

DIAGNOSIS (JR405E) 7A2-93
No. A1: Vehicle Does Not Run in D, 3, 2, L and R Range

Description:

Vehicle does not run though the accelerator pedal is stepped on.

Diagnosis Hints:

Some trouble in the AT main unit is supposed (since the vehicle can run even if the TCM is defective). However,
since the trouble of the main unit may be originated from the sensor system or output system, these systems
should be also checked to prevent reproduce of the trouble.

Possible Cause:

Slip of clutch (low clutch, low one-way clutch, reverse clutch, low & reverse brake).
If slip of clutch is caused, a DTC (gear ratio error) is stored.

Shortage or faulty quality of ATF.

Dropped line pressure.

Trouble in control valve body (faulty operation, sticking, clogged oil passage).

Disordered select cable (select indicator light indicates D, 3, 2, L or R but the hydraulic system is not in the D, 3,
2, L, or R range).

Faulty torque generated.

Trouble in the torque converter (faulty operation, sticking), insufficient engine output.

Malfunction of parking mechanism.

Step Action Yes No
1 Dislocation or disordered of select lever.
Does the vehicle move when the brake is released in a
position other than the P range and the vehicle is pushed?

Go to Step 2

Adjust the select cable.
2 Are any DTCs stored?
Go to DTC Chart Go to Step 3
3 Are the quantity, contamination and smell normal?
If the ATF level is low,
replenish up to the
specified level.

Go to Step 4
If ATF is extremely
black and
contaminated and
smells burnt, slip of the
clutch is supposed.
Overhaul the AT unit.
4 Is the stall revolution correct in all range? Refer the STALL
TEST section in this manual.
Go to Step 5
Repair the defect or
replace.
5 Is the line pressure correct? Refer the LINE PRESSURE
TEST section in this manual. Trouble in the AT
assembly or control
valve.
Repair the defect or
replace.

7A2-94 DIAGNOSIS (JR405E)
No. A2: Vehicle Does Not Run in R Range

Description:

Vehicle does not run in R range only.

It runs correctly in D, 3, 2, and L ranges.

Diagnosis Hints:

Some trouble in the AT main unit is supposed (since the vehicle can run even if the TCM is defective). However,
since the trouble of the main unit may be originated from the sensor system or output system, these systems
should be also checked to prevent reproduce of the trouble.

Possible Cause:

Slip of clutch (reverse clutch, low & reverse brake).
If slip of clutch is caused, a DTC (gear ratio error) is stored.

Shortage or faulty quality of ATF.

Dropped line pressure.

Trouble in control valve body (faulty operation, sticking, clogged oil passage).

Disordered select cable (select indicator light indicates R but the hydraulic system is not in the R range).

Faulty torque generated.

Trouble in the torque converter (faulty operation, sticking), insufficient engine output.

Malfunction of parking mechanism.

Step Action Yes No
1 Dislocation or disordered of select lever.
Does the vehicle move when the brake is released in a
position other than the P range and the vehicle is pushed?

Go to Step 2

Adjust the select cable.
2 Are any DTCs stored?
Go to DTC Chart Go to Step 3
3 Are the quantity, contamination and smell normal?
If the ATF level is low,
replenish up to the
specified level.

Go to Step 4

If ATF is extremely
black and
contaminated and
smells burnt, slip of the
clutch is supposed.
Overhaul the AT unit.
4 Is the stall revolution correct in R range? Refer the STALL
TEST section in this manual.
Go to Step 5
Repair the defect or
replace.
5 Is the line pressure correct? Refer the LINE PRESSURE
TEST section in this manual. Trouble in the AT
assembly or control
valve.
Repair the defect or
replace.

DIAGNOSIS (JR405E) 7A2-95
No. A3: Vehicle Does Not Run in D, 3, 2 and L Range

Description:

Vehicle does not run in D, 3, 2 and L range only.

It runs correctly in R ranges.

Diagnosis Hints:

Some trouble in the AT main unit is supposed (since the vehicle can run even if the TCM is defective). However,
since the trouble of the main unit may be originated from the sensor system or output system, these systems
should be also checked to prevent reproduce of the trouble.

Possible Cause:

Slip of clutch (low clutch and low one-way clutch).
If slip of clutch is caused, a DTC (gear ratio error) is stored.

Shortage or faulty quality of ATF.

Dropped line pressure.

Trouble in control valve body (faulty operation, sticking, clogged oil passage).

Disordered select cable (select indicator light indicates D, 3, 2 and L but the hydraulic system is not in the D, 3, 2
and L range).

Faulty torque generated.

Trouble in the torque converter (faulty operation, sticking), insufficient engine output.

Malfunction of parking mechanism.

Step Action Yes No
1 Dislocation or disordered of select lever.
Does the vehicle move when the brake is released in a
position other than the P range and the vehicle is pushed?

Go to Step 2

Adjust the select cable.
2 Are any DTCs stored?
Go to DTC Chart Go to Step 3
3 Are the quantity, contamination and smell normal?
If the ATF level is low,
replenish up to the
specified level.

Go to Step 4

If ATF is extremely
black and
contaminated and
smells burnt, slip of the
clutch is supposed.
Overhaul the AT unit.
4 Is the stall revolution correct in D, 3, 2 and L range? Refer
the STALL TEST section in this manual.
Go to Step 5
Repair the defect or
replace.
5 Is the line pressure correct? Refer the LINE PRESSURE
TEST section in this manual. Trouble in the AT
assembly or control
valve.
Repair the defect or
replace.

7A2-96 DIAGNOSIS (JR405E)
No. B1: Vehicle Runs in N Range

Description:

Creep appears in N range.

Vehicle moves unless the brake pedal is stepped on in N range.

Diagnosis Hints:

Basically a trouble in the AT main unit. However, some trouble in the sensor system or output system may have
some influence on the trouble in the main unit and therefore these systems should be also checked to prevent
reproduce of the trouble.

Possible Cause:

Seized clutch (low clutch, low one-way clutch, reverse clutch, low & reverse brake).

Trouble in the control valve (faulty operation, sticking, clogged oil passage).

Dislocated select lever (the select indicator light indicates the N range but the hydraulic system is in the D, 3, 2
or L range).

Step Action Yes No
1 Dislocation or disordered of select lever.
Does the vehicle move when the brake is released in a
position other than the P range and the vehicle is pushed?

Go to Step 2

Adjust the select cable.
2 Are any DTCs stored?
Go to DTC Chart Go to Step 3
3 Are the quantity, contamination and smell normal?
If the ATF level is low,
replenish up to the
specified level.

Trouble in the AT
assembly or control
valve.

If ATF is extremely
black and
contaminated and
smells burnt, slip of the
clutch is supposed.
Overhaul the AT unit.

DIAGNOSIS (JR405E) 7A2-107
No. B10: Brake is Applied in R Range

Description:

Brake is applied suddenly in R range.

Diagnosis Hints:

Basically a trouble in the AT main unit. However, some trouble in the sensor system or output system may have
some influence on the trouble in the main unit and therefore these systems should be also checked to prevent
reproduce of the trouble.

Possible Cause:

Seized clutch (low clutch, high clutch, 2-4 brake).

Shortage or faulty quality of ATF.

Trouble in control valve body (faulty operation, sticking, clogged oil passage).

Disordered select cable (select indicator light indicates R but the hydraulic system is not in the R range).

Malfunction of parking mechanism.


No. B11: Insufficient Starting or Shaking in D Range

Description:

Insufficient starting or shaking in D range.

Possible Cause:

Slip of clutch (low clutch, low one-way clutch, reverse clutch, low & reverse brake).
If slip of clutch is caused, a DTC (gear ratio error) is stored.

Shortage or faulty quality of ATF.

Dropped line pressure.

Trouble in control valve body (faulty operation, sticking, clogged oil passage).


No. B12: Noise or Vibration is Generated at Starting

Description:

Noise or vibration is generated in the vicinity of AT at starting.

Diagnosis Hints:

Cause other than AT can be also considered. It is effective means to reproduce a running condition using a lift
up, chassis dynamo, etc. to investigate the origin (generating condition) of noise and vibration.
Caution:
Lifting up some unit to test it accompanies danger. Provide safety measures as far as possible and
carry out the test with sufficient care.

Possible Cause:
Following sources of noise or vibration other than the AT can be considered.

Noise from differential gears.

Noise from propeller shaft.

The bearing support in the middle of the propeller shaft has fatigued, and the bend angle of the propeller shaft
has changed, causing vibration at the time of start.

Unbalanced and poor uniformity of tires cause vibration.