2004 ISUZU TF SERIES engine

ELECTRICAL-BODY AND CHASSIS 8A-433


No. Connector face No. Connector face
H-1
White
Battery (+) ~ Engine room H-10
WhiteINST ~ Front Door-RH
H-2
NOT USED H-11
NOT USED
H-3
(6VE1,
4JH1-TC)
White Battery (+) ~ Engine room H-12
BlackINST ~ Roof
H-4
(C24SE)
White Engine room ~ Mission H-13
WhiteINST ~ Door -LH
H-4
(6VE1,
4JA1-TC,
4JH1-TC)
White
Engine ~ Engine room H-14
WhiteRear body ~ Rear door-LH
H-5
NOT USED H-15
White
Engine room ~ Chassis
H-6
White
Engine room ~ INST H-16
WhiteRear body ~ Rear door-RH
H-7
White
Engine room ~ INST H-17
WhiteChassis ~ License plate lamp
H-8
NOT USED H-18
White
Engine room ~ INST
H-9
Blue
Engine room ~ Chassis H-19
~
H-21 NOT USED

8A-434 ELECTRICAL-BODY AND CHASSIS


No. Connector face No. Connector face
H-22
(6VE1)
(4JH1-TC)
White Engine ~ Engine room C H-31
(C24SE)
Engine room ~ Mission
H-23
(6VE1)
(4JH1-TC)
White Engine ~ Engine room B H-32
(C24SE)
(6VE1)
Engine room ~ Rear body
H-23
(4JA1-L)
White Engine room B ~ T/misson H-33
(4JH1-TC)
Engine ~ Engine room
H-24
Black
INST ~ Front door-RH H-34
(C24SE)
Engine ~ Engine room
H-25
Black
INST ~ Front door-LH H-35

Trailer
H-26
White
INST ~ Rear body


H-27
Black
INST ~ Rear body


H-28
White
Sub harness connector


H-29
(C24SE)
Battery(+) ~ Engine room


H-30
(6VE1)
(4JH1-TC)
Engine room ~ INST

ELECTRICAL-BODY AND CHASSIS 8A-437


No. Connector face No. Connector face
P-1
Silver
Battery (+) P-9

SilverACG (B)
P-2
Silver
Relay & Fuse box P-10
SilverEngine ground
P-3

Brown
Starter (S) P-11
SilverFuse & relay box
P-4
Silver
Starter (B) P-12
NOT USED
P-4
Silver
Starter (B) P-13

Gray Shift on the fly actuator
P-5
Silver
Battery (-) P-14
WhiteFuse & relay box
P-6
Silver
Body earth (Ground) P-15
Silver2nd battery (+)
P-7
NOT USED P-16
Silver
2nd battey (-)
P-8
(C24SE)
(4JH1-TC
Green ACG (L)


P-8
(6VE1)
White ACG (L)

CRUISE CONTROL SYSTEM 8B-17
DTC 2–1 Signal of Vehicle Speed Malfunction
Step Action Value(s) YES NO
1 Check the DTC for engine.
Is the vehicle speed sensor DTC set?
—
Go to DTC for
engine


Go to Step 2

2 Check continuity between harness side connector
E–44 terminal 3 and connector C–120 terminal 9.
Is there continuity between terminals?

—

Go to Step 3
Replace open
circuit
3 Check the continuity between harness side
connector E–44 terminal 3 and ground, connector
C–120 terminal 9 and ground.
Are the results same as specified in the value(s)
column?



No continuity



Replace the
control unit


Repair short
circuit

WORKSHOP MANUAL

TF SERIES




ENGINE
4JA1/4JH1-TC





SECTION 6

TROUBLESHOOTING 6 – 1


SECTION 6
TROUBLESHOOTING


TABLE OF CONTENTS
PAGE PAGE
BASIC INSPECTION PROCEDURE ... 6– 2

1. HARD STARTING ........................... 6– 3

1-1.Starter Motor Inoperative ......... 6– 3

1-2. Starter Motor Operates But
Engine Does Not Turn Over .......... 6– 3

1-3. Engine Turns Over But Does
Not Start Engine ............................. 6– 4

2. UNSTABLE IDLING ........................ 6– 5

3. INSUFFICIENT POWER ................. 6– 6

4. EXCESSIVE FUEL
CONSUMPTION ................................. 6– 7

5. EXCESSIVE OIL CONSUMPTION.. 6– 8

6. OVERHEATING............................... 6– 9

7. WHITE EXHAUST SMOKE ............. 6– 9

8. DARK EXHAUST SMOKE .............. 6– 10

9. OIL PRESSURE DOES NOT RISE . 6– 11

10. ABNORMAL ENGINE NOISE ....... 6– 12

10-1. Engine Knocking.................... 6– 12

10-2. Gas Leakage Noise ................ 6– 12

10-3. Continuous Noise .................. 6– 13

10-4. Slapping Noise ....................... 6– 13

10-5. Excessive Turbocharger
Noise ............................................... 6– 14
11. ROTATING PART WEAR OF
TURBOCHARGER ............................. 6– 14

12. OIL LEAKAGE FROM
TURBOCHRGER ............................... 6– 15

13. INSUFFICIENT ACCELERATION
AND/OR LACK OF POWER DUE
TO TURBOCHARGER ....................... 6– 15

14. BATTERY CHARGING AND
NOISE PROBLEM.............................. 6– 16

14-1. Battery No Charging .............. 6– 16

14-2. Battery Overcharging ............ 6– 16

14-3. Battery Under Charging......... 6– 17

14-4. Battery Unstable Charging
Current ............................................ 6– 17

14-5. Charging System Noise ......... 6– 18

15. STARTER MOTOR PROBLEM..... 6– 19

15-1. Starter Motor Pinion Engages
to Ring Gear But Engine Does
Not Turn Over ................................. 6– 19

15-2. Incorrect Pinion And Ring
Gear Engagement .......................... 6– 19

15-3. Starter Motor Continues To
Run After The Starter Switch Is
Turned Off ....................................... 6– 20

15-4. Excessive Commutator
Sparking .......................................... 6– 20

6 – 2 TROUBLESHOOTING
Basic Inspection Procedure
Follow the under inspection procedure, when the problem vehicle comes workshop.
Step Inspection point Inspection result YES NO
1 Check the check engine lamp Is the check engine lamp turn
ON ? Go to section
6E “On Board
Diagnostic
(OBD) System
Check" Go to Step 2
2 The battery fluid level and the
gravity Was the problem found? Re-charge the
battery or
replace the
battery Go to Step 3
3 The engine coolant capacity Was the problem found? Replenish the
engine coolant Go to Step 4
4 The engine oil level Was the problem found? Replenish the
engine oil Go to Step 5
5 The air cleaner element Was the problem found? Clean or
replace Go to Step 6
6 The piping fixing condition (oil,
vacuum and fuel piping) Was the problem found? Return normal
condition Go to Step 7
7 The drive belt tension and break Was the problem found? Re-adjust the
tension or
replace Go to Step 8
8 Go to section 6E “On Board
Diagnostic (OBD) System
Check” Was the problem found?
Verify repair Go to Step 9
9 Go to mechanical
troubleshooting chart Was the problem found?
Verify repair —

TROUBLESHOOTING 6 – 3
1. Hard Starting
Inspect the following items before diagnosis.
1. The battery conditions.
The terminal connection condition.
The battery charge condition or battery power weakness.
2. The fan belt loosen or broken.
3. The main fuse condition (open or not).
4. Fuel quantity level.
1–1 Starter motor inoperative
Step Action Value(s) Yes No
1 Check the starter switch.
Does the starter switch work? —
Go to Step 2 Repair or
replace the
starter switch
2 Check the starter relay.
Does the starter relay work? —
Go to Step 3 Repair or
replace the
starter relay
3 Check the magnetic switch.
Does the magnetic switch work? —
Go to Step 4 Repair or
replace the
magnetic
switch
4 Check the pinion gear condition on the starter motor.
Was the condition normal? —
Go to Step 5 Replace the
pinion gear
5 Check the brush wear or brush spring weakness.
Was the condition normal? —
Replace the
starter motor
assembly Repair or
replace the
brush or brush
spring

1-2 Starter motor operates but engine does not turn over
Step Action Value(s) Yes No
1 Check the engine internal seizure.
Was the engine seized? —
Repair or
replace seized
parts Check other
DTC by Tech
2 and go to
indicated DTC