2004 INFINITI QX56 check engine

DI-38
WARNING LAMPS
Revision: August 20072004 QX56
Oil Pressure Warning Lamp Stays Off (Ignition Switch ON)EKS007EA
1. CHECK OIL PRESSURE SENSOR SIGNAL
1. Turn ignition switch ON.
2. Check voltage between combination meter harness connector
M24 terminal 20 (Y) and ground.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
2. CHECK OIL PRESSURE SENSOR GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector M24 and oil pressure
sensor connector F4.
3. Check continuity between combination meter harness connector
M24 terminal 16 (B/P) and oil pressure sensor harness connec-
tor F4 terminal 3 (B/P).
OK or NG
OK >> Replace the combination meter. Refer to IP-13, "Combi-
nation Meter" .
NG >> Repair harness or connector.
3. CHECK OIL PRESSURE SENSOR REFERENCE VOLTAGE
1. Turn ignition switch OFF.
2. Disconnect oil pressure sensor connector F4.
3. Turn ignition switch ON.
4. Check voltage between combination meter harness connector
M24 terminal 22 (GR/L) and ground.
OK or NG
OK >> GO TO 4.
NG >> Replace the combination meter. Refer to IP-13, "
Combi-
nation Meter" .
Terminals
Condition Voltage (V) (+)
(–)
ConnectorTe r m i n a l
(Wire color)
M24 20 (Y) GroundWhen ignition switch is in ON
position. (Engine stopped)Ye s
Engine running. (Idle speed) Yes
WKIA1833E
Continuity should exist.
WKIA1837E
Voltage : Approx. 5V
WKIA1834E

DI-40
WARNING LAMPS
Revision: August 20072004 QX56
Oil Pressure Warning Lamp Does Not Turn Off (Oil Pressure Is Normal)EKS007EB
NOTE:
For oil pressure inspection, refer to LU-7, "
OIL PRESSURE CHECK" .
1. CHECK ENGINE OIL PRESSURE GAUGE OPERATION
Observe operation of engine oil pressure gauge.
Does engine oil pressure gauge function properly?
YES >> Replace the combination meter. Refer to DI-25, "Removal and Installation of Combination Meter"
.
NO >> Go to DI-19, "
Engine Oil Pressure Signal Inspection" .

REAR SONAR SYSTEM
DI-65
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: August 20072004 QX56
Pre-diagnosis InspectionEKS007EX
SENSOR STATUS CHECK

Check that the rear sonar sensor is properly aligned (bumper is not misaligned, no deformation in sensor
mounting area.

Check that snow, mud, or other foreign objects are not adhering to the rear sonar sensor.

Check that there is no deformation, scratches, or other damage to the rear sonar sensor.

Check that water has not accumulated in the rear sonar sensor.
CAUTION:
Use water, cotton swab, or other soft material for cleaning the sensor.
1. Check that there are no obstacles within each rear sonar sensor's detection range.
2. Check that there are no nearby ultrasound sources (such as the sounds of vehicle horns, motorcycle
engines, or truck air brakes).
3. Check that the vehicle is on a level surface.
Self-diagnosis FunctionEKS007EY
There are four modes of self-diagnosis; entering diagnostics, requesting number of fault codes, requesting
fault codes, and idling or clearing fault codes. These steps must be followed in order. Self-diagnosis can be
manually exited by turning the ignition switch OFF, or selecting reverse gear. Self-diagnosis will exit unless a
fault code request occurs before a message is repeated five times without acknowledgement.
ENTERING DIAGNOSTICS MODE
1. Turn ignition switch ON. Rear sonar system OFF switch indica-
tor lamp illuminates for three seconds and then turns off.
2. Immediately push rear sonar system OFF switch ten times
within five seconds.
3. The sonar buzzer will sound once and the rear sonar system
OFF indicator will flash once.
REQUESTING NUMBER OF FAULT CODES MODE
1. While in diagnostic mode, push rear sonar system OFF switch
once.
2. The sonar buzzer will sound once.
3. Rear sonar system OFF indicator will flash once and sonar
buzzer will sound once for each fault code detected.
4. There will be a four second pause.
5. The number of fault codes will repeat five times then pause.
NOTE:
Self-diagnosis will exit unless requesting fault codes occurs
before five repeats ends.
Detection range
Rear sonar sensors Approx. 1.8 m (5.9 ft.) maximum
LKIA0389E
LKIA0388E

EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION EC
A
EC
Revision: August 20072004 QX56 INDEX FOR DTC ........................................................ 8
Alphabetical Index .................................................... 8
DTC No. Index ....................................................... 12
PRECAUTIONS ........................................................ 16
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................ 16
On Board Diagnostic (OBD) System of Engine and
A/T .......................................................................... 16
Precaution .............................................................. 16
Wiring Diagrams and Trouble Diagnosis ................ 19
PREPARATION ......................................................... 20
Special Service Tools ............................................. 20
Commercial Service Tools ...................................... 22
ENGINE CONTROL SYSTEM .................................. 23
System Diagram ..................................................... 23
Vacuum Hose Drawing ........................................... 24
System Chart ......................................................... 25
Multiport Fuel Injection (MFI) System .................... 26
Electronic Ignition (EI) System ............................... 28
Nissan Torque Demand (NTD) Control System ..... 29
Air Conditioning Cut Control ................................... 30
Fuel Cut Control (at No Load and High Engine
Speed) .................................................................... 30
CAN communication .............................................. 31
BASIC SERVICE PROCEDURE .............................. 32
Idle Speed and Ignition Timing Check .................... 32
Idle Speed/Ignition Timing/Idle Mixture Ratio
Adjustment ............................................................. 33
Accelerator Pedal Released Position Learning ...... 44
Throttle Valve Closed Position Learning ................ 44
Idle Air Volume Learning ........................................ 44
Fuel Pressure Check .............................................. 46
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 49
Introduction ............................................................ 49
Two Trip Detection Logic ........................................ 49
Emission-related Diagnostic Information ................ 50
IVIS (Infiniti Vehicle Immobilizer System — NATS) ... 63
Malfunction Indicator Lamp (MIL) ........................... 63
OBD System Operation Chart ................................ 66TROUBLE DIAGNOSIS ............................................ 71
Trouble Diagnosis Introduction ............................... 71
DTC Inspection Priority Chart ................................. 76
Fail-safe Chart ........................................................ 77
Basic Inspection ..................................................... 79
Symptom Matrix Chart ............................................ 84
Engine Control Component Parts Location ............ 88
Circuit Diagram ....................................................... 94
ECM Harness Connector Terminal Layout ............. 96
ECM Terminals and Reference Value ..................... 96
CONSULT-II Function ...........................................103
Generic Scan Tool (GST) Function .......................116
CONSULT-II Reference Value in Data Monitor .....118
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................121
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .123
Description ............................................................123
Testing Condition ..................................................123
Inspection Procedure ............................................123
Diagnostic Procedure ...........................................124
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................127
Description ............................................................127
Diagnostic Procedure ...........................................127
POWER SUPPLY AND GROUND CIRCUIT ...........128
Wiring Diagram .....................................................128
Diagnostic Procedure ...........................................129
Ground Inspection ................................................133
DTC U1000, U1001 CAN COMMUNICATION LINE .135
Description ............................................................135
On Board Diagnosis Logic ....................................135
DTC Confirmation Procedure ...............................135
Wiring Diagram .....................................................136
Diagnostic Procedure ...........................................137
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER .138
Description ............................................................138
CONSULT-II Reference Value in Data Monitor Mode
.138
On Board Diagnosis Logic ....................................138
DTC Confirmation Procedure ...............................139

EC-5
C
D
E
F
G
H
I
J
K
L
M
ECA
Revision: August 20072004 QX56 Overall Function Check ........................................ 396
Wiring Diagram .................................................... 398
Diagnostic Procedure ........................................... 401
Component Inspection ......................................... 404
Removal and Installation ...................................... 406
DTC P1148, P1168 CLOSED LOOP CONTROL .... 407
On Board Diagnosis Logic ................................... 407
DTC P1211 TCS CONTROL UNIT ......................... 408
Description ........................................................... 408
On Board Diagnosis Logic ................................... 408
DTC Confirmation Procedure ............................... 408
Diagnostic Procedure ........................................... 408
DTC P1212 TCS COMMUNICATION LINE ............ 409
Description ........................................................... 409
On Board Diagnosis Logic ................................... 409
DTC Confirmation Procedure ............................... 409
Diagnostic Procedure ........................................... 409
DTC P1217 ENGINE OVER TEMPERATURE ....... 410
Description ........................................................... 410
CONSULT-II Reference Value in Data Monitor Mode
. 410
On Board Diagnosis Logic .................................... 411
Overall Function Check ......................................... 411
Wiring Diagram .................................................... 413
Diagnostic Procedure ........................................... 415
Main 12 Causes of Overheating ........................... 418
Component Inspection ......................................... 419
DTC P1225 TP SENSOR ........................................ 420
Component Description ........................................ 420
On Board Diagnosis Logic ................................... 420
DTC Confirmation Procedure ............................... 420
Diagnostic Procedure ........................................... 421
Removal and Installation ...................................... 421
DTC P1226 TP SENSOR ........................................ 422
Component Description ........................................ 422
On Board Diagnosis Logic ................................... 422
DTC Confirmation Procedure ............................... 422
Diagnostic Procedure ........................................... 423
Removal and Installation ...................................... 423
DTC P1229 SENSOR POWER SUPPLY ................ 424
On Board Diagnosis Logic ................................... 424
DTC Confirmation Procedure ............................... 424
Wiring Diagram .................................................... 425
Diagnostic Procedure ........................................... 426
DTC P1271, P1281 A/F SENSOR 1 ....................... 429
Component Description ........................................ 429
CONSULT-II Reference Value in Data Monitor Mode
. 429
On Board Diagnosis Logic ................................... 429
DTC Confirmation Procedure ............................... 429
Wiring Diagram .................................................... 431
Diagnostic Procedure ........................................... 434
Removal and Installation ...................................... 436
DTC P1272, P1282 A/F SENSOR 1 ....................... 437
Component Description ........................................ 437
CONSULT-II Reference Value in Data Monitor Mode
. 437
On Board Diagnosis Logic ................................... 437
DTC Confirmation Procedure ............................... 437Wiring Diagram .....................................................439
Diagnostic Procedure ...........................................442
Removal and Installation ......................................444
DTC P1273, P1283 A/F SENSOR 1 .......................445
Component Description ........................................445
CONSULT-II Reference Value in Data Monitor Mode
.445
On Board Diagnosis Logic ....................................445
DTC Confirmation Procedure ...............................445
Wiring Diagram .....................................................447
Diagnostic Procedure ...........................................450
Removal and Installation ......................................453
DTC P1274, P1284 A/F SENSOR 1 .......................454
Component Description ........................................454
CONSULT-II Reference Value in Data Monitor Mode
.454
On Board Diagnosis Logic ....................................454
DTC Confirmation Procedure ...............................454
Wiring Diagram .....................................................456
Diagnostic Procedure ...........................................459
Removal and Installation ......................................462
DTC P1276, P1286 A/F SENSOR 1 .......................463
Component Description ........................................463
CONSULT-II Reference Value in Data Monitor Mode
.463
On Board Diagnosis Logic ....................................463
DTC Confirmation Procedure ...............................463
Overall Function Check ........................................464
Wiring Diagram .....................................................466
Diagnostic Procedure ...........................................469
Removal and Installation ......................................471
DTC P1278, P1288 A/F SENSOR 1 .......................472
Component Description ........................................472
CONSULT-II Reference Value in Data Monitor Mode
.472
On Board Diagnosis Logic ....................................472
DTC Confirmation Procedure ...............................473
Wiring Diagram .....................................................475
Diagnostic Procedure ...........................................478
Removal and Installation ......................................483
DTC P1279, P1289 A/F SENSOR 1 .......................484
Component Description ........................................484
CONSULT-II Reference Value in Data Monitor Mode
.484
On Board Diagnosis Logic ....................................484
DTC Confirmation Procedure ...............................485
Wiring Diagram .....................................................487
Diagnostic Procedure ...........................................490
Removal and Installation ......................................495
DTC P1444 EVAP CANISTER PURGE VOLUME
CONTROL SOLENOID VALVE ...............................496
Description ............................................................496
CONSULT-II Reference Value in Data Monitor Mode
.496
On Board Diagnosis Logic ....................................497
DTC Confirmation Procedure ...............................497
Wiring Diagram .....................................................498
Diagnostic Procedure ...........................................500

EC-20Revision: August 2007
PREPARATION
2004 QX56
PREPARATIONPFP:00002
Special Service ToolsUBS00GZ9
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool nameDescription
EG17650301
(J-33984-A)
Radiator cap tester
adapterAdapting radiator cap tester to radiator cap and ra-
diator filler neck
a: 28 (1.10) dia.
b: 31.4 (1.236) dia.
c: 41.3 (1.626) dia.
Unit: mm (in)
KV10117100
(J-36471-A)
Heated oxygen sensor
wrenchLoosening or tightening heated oxygen sensors
with 22 mm (0.87 in) hexagon nut
KV10114400
(J-38365)
Heated oxygen sensor
wrenchLoosening or tightening heated oxygen sensors
a: 22 mm (0.87 in)
(J-44626)
Air fuel ratio (A/F) sen-
sor wrenchLoosening or tightening air fuel ratio (A/F) sensor 1
(J-44321)
Fuel pressure gauge
kitChecking fuel pressure
(J-44321-6)
Fuel pressure adapterConnecting fuel pressure gauge to quick connec-
tor type fuel lines.
(J-45488)
Quick connector re-
leaseRemove fuel tube quick connectors in engine
room.
S-NT564
S-NT379
S-NT636
LEM054
LEC642
LBIA0376E
PBIC0198E

PREPARATION
EC-21
C
D
E
F
G
H
I
J
K
L
MA
EC
Revision: August 20072004 QX56
KV109E0010
(J-46209)
Break-out boxMeasuring the ECM signals with a circuit tester
KV109E0080
(J-45819)
Y-cable adapterMeasuring the ECM signals with a circuit tester
(J-23688)
Engine coolant refrac-
tometerChecking concentration of ethylene glycol in en-
gine coolant Tool number
(Kent-Moore No.)
Tool nameDescription
S-NT825
S-NT826
W BIA0539E

EC-22Revision: August 2007
PREPARATION
2004 QX56
Commercial Service ToolsUBS00GZA
Tool name
(Kent-Moore No.)Description
Leak detector
i.e.: (J-41416)Locating the EVAP leak
EVAP service port
adapter
i.e.: (J-41413-OBD)Applying positive pressure through EVAP service
port
Fuel filler cap adapter
i.e.: (MLR-8382)Checking fuel tank vacuum relief valve opening
pressure
Socket wrench Removing and installing engine coolant tempera-
ture sensor
Oxygen sensor thread
cleaner
i.e.: (J-43897-18)
(J-43897-12)Reconditioning the exhaust system threads before
installing a new oxygen sensor. Use with anti-
seize lubricant shown below.
a: 18 mm diameter with pitch 1.5 mm for Zirco-
nia Oxygen Sensor
b: 12 mm diameter with pitch 1.25 mm for Tita-
nia Oxygen Sensor
Anti-seize lubricant
i.e.: (Permatex
TM
133AR or equivalent
meeting MIL specifica-
tion MIL-A-907)Lubricating oxygen sensor thread cleaning tool
when reconditioning exhaust system threads.
S-NT703
S-NT704
S-NT815
S-NT705
AEM488
S-NT779