2004 INFINITI FX35 ignition

TROUBLE DIAGNOSIS
BRC-53
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2004 November 2004 FX35/FX45
Inspection 14: CAN Communication SystemAFS002Q9
DTC U1000, C1156
INSPECTION PROCEDURE
1. CHECK CONNECTOR
1. Turn ignition switch OFF, disconnect the ABS actuator and electric unit (control unit) connector, and check
the terminal for deformation, disconnection, looseness, and so on. If there is a malfunction, repair or
replace the terminal.
2. Reconnect connector to perform self-diagnosis.
Is
“CAN COMM CIRCUIT” or “ST ANG SEN COM CIR” displayed in the self-diagnosis display items?
YES >> Print out the self-diagnostic results, and refer to LAN-4, "Precautions When Using CONSULT-II" .
NO >> Connector terminal connection is loose, damaged, open, or shorted.
Component InspectionAFS001T6
VDC OFF SWITCH

Turn ignition switch OFF and disconnect VDC OFF switch con-
nector, and check continuity between VDC OFF switch connec-
tor M32 terminals 1 and 2.
Symptom 1: Excessive ABS Function Operation FrequencyAFS001T7
1. FRONT AND REAR AXLE INSPECTION
Make sure there is no excessive looseness in the front and rear axles.
OK or NG
OK >> GO TO 2.
NG >> Check front or rear axle system.
2. WHEEL SENSOR INSPECTION
Perform following inspection for wheel sensor:

Sensor mount and damage inspection

Sensor rotor mount and damage inspection

Sensor connector connection inspection

Sensor harness inspection
OK or NG
OK >> GO TO 3.
NG >> Sensor or sensor rotor replacement
3. ABS WARNING LAMP DISPLAY CHECK
Make sure warning lamp turns off approximately 2 sec. After turn ignition switch ON or when driving.
OK or NG
OK >> Normal
NG >> Perform self-diagnosis. Refer to BRC-27, "
SELF-DIAGNOSIS" . 1 -2 :Continuity should exist when pushing
switch.
continuity should not exist when releasing
switch.
SFIA1203E

BRC-54
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS
Revision: 2004 November 2004 FX35/FX45
Symptom 2: Unexpected Pedal ReactionAFS001T8
1. CHECK BRAKE PEDAL STROKE
Check brake pedal stroke.
Is the stroke too long?
YES >>
Bleed air from brake piping.

Check brake pedal, brake booster, and master cylinder mount for play, looseness, and brake
system for fluid leaks, etc. If any malfunctions are found, make repair.
NO >> GO TO 2.
2. CHECK FUNCTION
Disconnect ABS actuator and electric unit (control unit) connector E56 and make sure that braking force is suf-
ficient when ABS in not operating. After the inspection, reconnect connector.
OK or NG
OK >> GO TO symptom 1 “Step 2”. Refer to BRC-53, "Symptom 1: Excessive ABS Function Operation
Frequency" .
NG >> Check brake system.
Symptom 3: The Braking Distance Is LongAFS001T9
CAUTION:
On slippery road surfaces, the stopping distance might be longer with the ABS operating than when
the ABS is not operating.
1. CHECK FUNCTION
Disconnect ABS actuator and electric unit (control unit) connector E56 to deactivate ABS. In this condition,
check stopping distance. After inspection, connect connector.
OK or NG
OK >>
Bleed air from brake piping.

Check brake system.
NG >> GO TO symptom 1 “Step 2”. Refer to BRC-53, "
Symptom 1: Excessive ABS Function Operation
Frequency" .
Symptom 4: The ABS Function Does Not OperateAFS001TA
CAUTION:
The ABS does not operate when the speed is 10 km/h (6 MPH) or less.
1. CHECK ABS WARNING LAMP DISPLAY
Make sure warning lamp turns off approximately 2 second after the ignition switch is turned on or when driv-
ing.
OK or NG
OK >> GO TO symptom 1 “Step 2”. Refer to BRC-53, "Symptom 1: Excessive ABS Function Operation
Frequency" .
NG >> Perform self-diagnosis. Refer to BRC-27, "
SELF-DIAGNOSIS" .

TROUBLE DIAGNOSIS
BRC-55
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
Revision: 2004 November 2004 FX35/FX45
Symptom 5: Pedal Vibration or ABS Operation Sound OccursAFS001TB
CAUTION:
Under the following conditions, when brake pedal is lightly depressed (just place a foot on it), ABS is
activated and vibration is felt. However, this is normal.

When shifting gears

When driving on slippery road

During cornering at high speed

When passing over bumps or grooves

When pulling away just after starting engine [at approximately 10 km/h (6MPH) or higher]
1. SYMPTOM CHECK 1
Check if pedal vibration or operation sound occurs when engine is started.
OK or NG
OK >> Perform self-diagnosis. Refer to BRC-27, "SELF-DIAGNOSIS" .
NG >> GO TO 2.
2. SYMPTOM CHECK 2
Check symptom when electrical component (headlamps, etc.) switches are operated.
Does the symptom occur when the electrical component (head lamp, etc.) switches are operated?
YES >> Check if there is a radio, antenna, antenna lead wire, or wiring close to ABS actuator and electric
unit (control unit) (or its wiring), and if there is, move it farther away.
NO >> GO TO symptom 1 “Step 2”. Refer to BRC-53, "
Symptom 1: Excessive ABS Function Operation
Frequency" .
Symptom 6: Vehicle Jerks During VDC/TCS/ABS ControlAFS001TC
1. CHECK ENGINE SPEED SIGNAL
Perform CONSULT-II “DATA MONITOR” to check engine speed.
Is engine speed at idle 400 rpm or higher?
YES >> GO TO 3.
NO >> GO TO 2.
2. ABS WARNING LAMP DISPLAY CHECK
Make sure warning lamp turns off approximately 2 sec. After turn ignition switch ON or when driving.
OK or NG
OK >> System is normal.
NG >> GO TO 3.
3. CHECK ECM SELF-DIAGNOSTIC RESULTS
Perform ECM self-diagnosis.
Are self-diagnosis items displayed?
YES >> Check the corresponding items. Refer to EC-77, "TROUBLE DIAGNOSIS" (VQ35DE), EC-726,
"TROUBLE DIAGNOSIS" (VK45DE) in “Engine Control (EC section)”.
NO >> GO TO 4.
4. CHECK A/T SELF-DIAGNOSTIC RESULTS
Perform A/T self-diagnosis.
OK or NG
OK >> GO TO 5.
NG >> Check the corresponding items. Refer toAT- 4 2 , "
TROUBLE DIAGNOSIS" in “A/T”.

CO-8
[VQ35DE]
OVERHEATING CAUSE ANALYSIS
Revision: 2004 November 2004 FX35/FX45
Except cool-
ing system
parts mal-
function— Overload on engineAbusive drivingHigh engine rpm under no
load
Driving in low gear for
extended time
Driving at extremely high
speed
Powertrain system mal-
function
— Installed improper size
wheels and tires
Dragging brakes
Improper ignition timing
Blocked or restricted air
flowBlocked bumper —
— Blocked radiator grilleInstalled car brassiere
Mud contamination or
paper clogging
Blocked radiator —
Blocked condenser
Blocked air flow
Installed large fog lamp Symptom Check items

OVERHEATING CAUSE ANALYSIS
CO-33
[VK45DE]
C
D
E
F
G
H
I
J
K
L
MA
CO
Revision: 2004 November 2004 FX35/FX45
Except cool-
ing system
parts mal-
function— Overload on engineAbusive drivingHigh engine rpm under no
load
Driving in low gear for
extended time
Driving at extremely high
speed
Powertrain system mal-
function
— Installed improper size
wheels and tires
Dragging brakes
Improper ignition timing
Blocked or restricted air
flowBlocked bumper —
— Blocked radiator grilleInstalled car brassiere
Mud contamination or
paper clogging
Blocked radiator —
Blocked condenser
Blocked air flow
Installed large fog lamp Symptom Check items

DI-2Revision: 2004 November 2004 FX35/FX45Schematic ............................................................... 39
Wiring Diagram — WARN — .................................. 40
Oil Pressure Warning Lamp Stays Off (Ignition
Switch ON) ............................................................. 48
Oil Pressure Warning Lamp Does Not Turn Off (Oil
Pressure Is Normal) ................................................ 49
Component Inspection ............................................ 50
OIL PRESSURE SWITCH ................................... 50
A/T INDICATOR ........................................................ 51
Wiring Diagram — AT/IND — ................................. 51
A/T Indicator Is Malfunction .................................... 53
WARNING CHIME ..................................................... 55
Component Parts and Harness Connector Location ... 55
System Description ................................................. 55
FUNCTION .......................................................... 55
IGNITION KEY WARNING CHIME (WITHOUT
INTELLIGENT KEY) ............................................ 56
IGNITION KEY WARNING CHIME (WITH INTEL-
LIGENT KEY) ...................................................... 56
LIGHT WARNING CHIME ................................... 57
SEAT BELT WARNING CHIME ........................... 57
CAN Communication System Description .............. 57
CAN Communication Unit ....................................... 57
Schematic ............................................................... 58
Wiring Diagram — CHIME — ................................. 59
Terminals and Reference Value for BCM ................ 62
Terminals and Reference Value for Unified Meter
and A/C Amp. ......................................................... 63
Terminals and Reference Value for Combination
Meter ...................................................................... 64
How to Proceed With Trouble Diagnosis ................ 64
Preliminary Check .................................................. 65
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................... 65
CONSULT-II Function ............................................. 66
DIAGNOSTIC ITEMS DESCRIPTION ................. 66
CONSULT-II BASIC OPERATION PROCEDURE
... 66
DATA MONITOR .................................................. 67
ACTIVE TEST ..................................................... 67
SELF-DIAGNOSTIC RESULTS ........................... 67
All Warnings Are Not Operated .............................. 68
Key Warning Chime and Light Warning Chime Does
Not Operate (Seat Belt Warning Chime Does Oper-ate) .......................................................................... 69
Key Warning Chime Does Not Operate (Without
Intelligent Key) ........................................................ 70
Key Warning Chime Does Not Operate (With Intel-
ligent Key, When Mechanical Key Is Used) ............ 72
Key Warning Chime Does Not Operate (With Intel-
l i g e n t K e y , W h e n I n t e l l i g e n t K e y I s C a r r i e d W i t h T h e
Driver) ..................................................................... 74
Light Warning Chime Does Not Operate ................. 76
Seat Belt Warning Chime Does Not Operate .......... 77
CLOCK ...................................................................... 79
Wiring Diagram — CLOCK — ................................. 79
Removal and Installation of Clock ........................... 80
REMOVAL ............................................................ 80
INSTALLATION .................................................... 80
REAR VIEW MONITOR ............................................. 81
System Description ................................................. 81
POWER SUPPLY AND GROUND ....................... 81
AV COMMUNICATION LINE ............................... 81
REAR VIEW CAMERA OPERATION .................. 81
Component Parts and Harness Connector Location ... 82
Schematic ............................................................... 83
Wiring Diagram — R/VIEW — ................................ 84
Terminals and Reference Value for Rear View Cam-
era Control Unit ....................................................... 87
CONSULT-II Function ............................................. 87
CONSULT-II BASIC OPERATION ....................... 87
WORK SUPPORT ............................................... 88
DATA MONITOR .................................................. 89
Side Distance Guideline Correction ........................ 89
SIDE DISTANCE GUIDELINE CORRECTION
PROCEDURE ...................................................... 89
Power Supply and Ground Circuit Inspection ......... 91
Rear View Is Not Displayed With The A/T Selector
Lever In R-position .................................................. 92
The Rear View Image Is Distorted .......................... 96
Removal and Installation of Rear View Camera Con-
trol Unit .................................................................... 97
REMOVAL ............................................................ 97
INSTALLATION .................................................... 97
Removal and Installation of Rear View Camera ..... 97
REMOVAL ............................................................ 97
INSTALLATION .................................................... 98

DI-4
COMBINATION METERS
Revision: 2004 November 2004 FX35/FX45
COMBINATION METERSPFP:24814
System DescriptionAKS005MH
UNIFIED METER CONTROL UNIT

Speedometer, odo/trip meter, tachometer, fuel gauge and water temperature gauge are controlled by the
unified meter control unit, which is built into the combination meter. Unified meter control unit receives sig-
nals from unified meter and A/C amp.

Warning lamp and indicator lamp of combination meter are controlled by signals drawn from the unified
meter and A/C amp.

Digital meter is adopted for odo/trip meter*.
*The record of the odo meter is kept even if the battery cable is disconnected. The record of the trip meter
is erased when the battery cable is disconnected.

Odo/trip meter, A/T indicator and ICC system display segments can be checked in diagnosis mode.

Meters/gauges can be checked in diagnosis mode.
Illumination Control
The unified meter control unit outputs the odo/trip meter and A/T
indicator lighting when the ignition switch is turned on. When the
lighting switch is turned on, light on for the combination meter dial,
illumination control switch and external lighting are output. In addi-
tion, when the lighting switch is turned on, the illumination control
switch on the left side of the combination meter can be used to
adjust the brightness of each light. The brightness can be adjusted
to sixteen different levels: From 0 (no lights) to 15 (maximum).
Pressing the illumination control switch will brighten or darken the
lights. When the key switch is in the START position, the combina-
tion meter dial lighting and illumination control switch lighting are
turned off.
UNIFIED METER AND A/C AMP.
Refer to DI-28, "System Description" in “UNIFIED METER AND A/C AMP”.
SKIA4795E

COMBINATION METERS
DI-5
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: 2004 November 2004 FX35/FX45
HOW TO CHANGE THE DISPLAY FOR ODO/TRIP METER

The vehicle speed signal and the memory signals from the meter memory circuit are processed by the
combination meter and the mileage is displayed.

Switch modes with following procedure.

When trip transfer switch is pressed, trip meter display changes.

If trip reset switch is pressed for 1 second or more while trip A is
displayed, only trip A is reset. (Same with trip B.)

If the battery is disconnected, odometer mileage will be retained
but the trip meter is reset to 0.0.
POWER SUPPLY AND GROUND CIRCUIT
Power is supplied at all times

through 10A fuse [No. 19, located in the fuse block (J/B)]

to combination meter terminal 8, and

to unified meter and A/C amp. terminal 21.
With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 14, located in the fuse block (J/B)]

to combination meter terminal 7

through 10A fuse [No. 12, located in the fuse block (J/B)]

to unified meter and A/C amp. terminal 22.
With the ignition switch in the ACC or ON position, power is supplied

through 15A fuse [No. 10, located in the fuse block (J/B)], and

through 15A fuse [No. 11, located in the fuse block (J/B)]

to unified meter and A/C amp. terminal 46.
Ground is supplied

to combination meter terminals 5, 6 and 15

through body grounds M35, M45 and M85

to unified meter and A/C amp. terminals 29 and 30

through body grounds M35, M45 and M85.
PKIA2382E
SKIA4817E