2004 INFINITI FX35 key

BL-134
INTELLIGENT KEY SYSTEM
Revision: 2004 November 2004 FX35/FX45
5. DOOR REQUEST SWITCH CIRCUIT INSPECTION
1. Disconnect Intelligent Key unit connector.
2. Check continuity between Intelligent Key unit connector M34 terminals 5 (driver door), 25 (passenger
door), and 29 (back door) and door request switch connector D12 (driver door), D42 (passenger door),
D113 (back door) terminal 1.
3. Check continuity between door request switch connector D12
(driver door), D42 (passenger door), D113 (back door) terminal
1 and ground.
OK or NG
OK >> Replace Intelligent Key unit.
NG >> Repair or replace harness between Intelligent Key unit and door request switch.
Check Intelligent Key Warning BuzzerAIS004NI
1. INTELLIGENT KEY WARNING BUZZER POWER SUPPLY CIRCUIT INSPECTION
1. Turn ignition knob LOCK position.
2. Disconnect Intelligent Key warning buzzer connector.
3. Check voltage between Intelligent Key warning buzzer connector D11 (driver side), D41 (passenger side)
terminal 1 (L) and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace Intelligent Key warning buzzer power
supply circuit.
2. INTELLIGENT KEY WARNING BUZZER CIRCUIT INSPECTION
1. Disconnect Intelligent Key unit connector.
2. Check continuity between Intelligent Key unit connector M34 terminal 4 and Intelligent Key warning
buzzer connector D11 (driver side), D41 (passenger side) terminal 2 (G).
3. Check continuity between Intelligent Key warning buzzer con-
nector D11 (driver side), D41 (passenger side) terminal 2 (G)
and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness between Intelligent Key warn-
ing buzzer and Intelligent Key unit. Driver 5 (W/L) - 1 (SB) : Continuity should exist.
Passenger 25 (W/R) - 1 (GY) : Continuity should exist.
Back door 29 (GY) - 1 (GY) : Continuity should exist.
1 - Ground : Continuity should not exist.
PIIA6747E
1 (L) - Ground : Battery voltage
PIIA6748E
4 (LG) - 2 (G) : Continuity should exist.
2 (G) - Ground : Continuity should not exist.
PIIA6749E

INTELLIGENT KEY SYSTEM
BL-135
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2004 November 2004 FX35/FX45
3. INTELLIGENT KEY WARNING BUZZER OPERATION INSPECTION
Connect battery power supply to Intelligent Key warning buzzer connector D11 (driver side), D41 (passenger
side) terminals 1 and 2, and check the operation.
OK or NG
OK >> Intelligent Key warning buzzer is OK.
NG >> Replace Intelligent Key warning buzzer
Check Outside Key AntennaAIS004NJ
1. OUTSIDE KEY ANTENNA POWER SUPPLY INSPECTION
Push each door request switch, and use an oscilloscope to check voltage waveform of harness between Intel-
ligent Key unit connector M34 terminals 17 (back door), 19 (driver and rear LH door), and 37 (passenger and
rear RH door) and ground.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.1 (BAT+) - 2 (BAT-) : the buzzer sounds
PIIA6750E
Terminal (Wire color)
ConditionSignal
(Reference value)
(+) (-)
Back door:
17 (OR/L)
GroundPush each
door request
switch Driver, rear LH:
19 (SB)
Passenger,
rear RH
37 (G)
MIIB0375ESIIA1910J

BL-136
INTELLIGENT KEY SYSTEM
Revision: 2004 November 2004 FX35/FX45
2. OUTSIDE KEY ANTENNA OPERATION INSPECTION
1. Disconnect each outside key antenna connector.
2. Check the following.
–Check continuity between door mirror (outside key antenna) connector D2 (driver side), D32 (passenger
side) terminals 6 and 7
–Check continuity between outside key antenna D62 (rear door LH), D82 (rear door RH), D116 (back door)
terminals 1 and 2
OK or NG
OK >> GO TO 3.
NG >> Replace outside key antenna.Driver side, Passenger side
6 - 7 : Continuity should exist.
Back door, Rear door
1 - 2 : Continuity should exist.
PIIA9931E

INTELLIGENT KEY SYSTEM
BL-137
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2004 November 2004 FX35/FX45
3. OUTSIDE KEY ANTENNA CIRCUIT INSPECTION
1. Disconnect Intelligent Key unit connector.
2. Check continuity between each outside key antenna connector D2 (driver side), D32 (passenger side),
D62 (rear door LH), D82 (rear door RH), D116 (back door) terminals 1, 2, 6, 7 and Intelligent Key unit con-
nector M34 terminals 17, 18, 19, 20, 37, and 38.
3. Check continuity between each out side key antenna connector
terminals 1, 2, 6, 7 and ground.
OK or NG
OK >> Replace Intelligent Key unit.
NG >> Replace harness between outside key antenna and Intelligent Key unit. Back door1 (L/B) - 17 (OR/L): Continuity should exist.
2 (W/B) - 18 (PU/R): Continuity should exist.
Driver side7 (BR/W) - 19 (SB): Continuity should exist.
6 (R/Y) - 20 (R/G): Continuity should exist.
Passenger side7 (G/Y) - 37 (G): Continuity should exist.
6 (L/Y) - 38 (PU/W): Continuity should exist.
Rear door LH1 (G/Y) - 19 (SB): Continuity should exist.
2 (PU/W) - 20 (R/G): Continuity should exist.
Rear door RH1 (G/Y) - 37 (G): Continuity should exist.
2 (PU/W) - 38 (PU/W): Continuity should exist.
Back door1 (L/B) - Ground: Continuity should not exist.
2 (W/B) - Ground: Continuity should not exist.
Rear door
(LH, RH)1 (G/Y) - Ground: Continuity should not exist.
2 (PU/W) - Ground: Continuity should not exist.
Driver side7 (BR/W) - Ground: Continuity should not exist.
6 (R/Y) - Ground: Continuity should not exist.
Passenger
side7 (G/Y) - Ground: Continuity should not exist.
6 (L/Y) - Ground: Continuity should not exist.
PIIA9932E

BL-138
INTELLIGENT KEY SYSTEM
Revision: 2004 November 2004 FX35/FX45
Check Inside Key AntennaAIS004NK
1. INSIDE KEY ANTENNA POWER SUPPLY CIRCUIT INSPECTION
Push ignition knob and use an oscilloscope to check voltage waveform between Intelligent Key unit connector
M34 terminals 13 (luggage room), 15 (dash board), 35 (dash board) and ground.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
2. INSIDE KEY ANTENNA OPERATION INSPECTION
1. Disconnect inside key antenna connector.
2. Check continuity between inside key antenna connector M70, M153 (dash board), B68 (luggage room)
terminals 1 and 2.
OK or NG
OK >> GO TO 3.
NG >> Replace malfunctioning inside key antenna.
Terminal (Wire color)
ConditionSignal
(Reference value)
(+) (-)
Luggage room:
13 (Y)
GroundPush igni-
tion knob. Dash board:
15 (W/R)
35 (LG)
PIIA6753ESIIA1910J
1 - 2 : Continuity should exist.
PIIA9933E

INTELLIGENT KEY SYSTEM
BL-139
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2004 November 2004 FX35/FX45
3. INSIDE KEY ANTENNA INSPECTION
1. Disconnect Intelligent Key unit connector.
2. Check continuity between inside key antenna connector M70, M153 (dash board), B68 (luggage room)
terminals 1, 2 and Intelligent Key unit connector terminals 13, 14, 15, 16, 35 and 36.
3. Check continuity between inside key antenna connector M70, M153 (dash board), B68 (luggage room)
terminals 1 and 2 and ground.
OK or NG
OK >> Replace Intelligent Key unit.
NG >> Repair or replace harness between inside key antenna and Intelligent Key unit.
Check Steering Lock UnitAIS004NL
1. STEERING LOCK UNIT POWER SUPPLY INSPECTION
1. Turn ignition knob LOCK position.
2. Disconnect steering lock unit connector.
3. Check voltage between steering lock unit connector M26 terminal 1 (L/R) and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace steering lock unit power supply circuit.Inside key
antenna-3 (Lug-
gage room)1 (OR/L) - 13 (Y): Continuity should exist.
2 (W/L) - 14 (BR): Continuity should exist.
Inside key
antenna-1 (Dash
board)1 (W/R) - 15 (W/R): Continuity should exist.
2 (B/R) - 16 (B/R): Continuity should exist.
Inside key
antenna-2 (Dash
board)1 (LG) - 35 (LG): Continuity should exist.
2 (PU) - 36 (PU): Continuity should exist.
Inside key
antenna-3 (Lug-
gage room)1 (OR/L) - Ground: Continuity should not exist.
2 (W/L) - Ground: Continuity should not exist.
Inside key
antenna-1 (Dash
board)1 (W/R) - Ground: Continuity should not exist.
2 (B/R) - Ground: Continuity should not exist.
Inside key
antenna-2 (Dash
board)1 (LG) - Ground: Continuity should not exist.
2 (PU) - Ground: Continuity should not exist.
PIIA6755E
1 (L/R) - Ground : Battery voltage
PIIA6797E

BL-140
INTELLIGENT KEY SYSTEM
Revision: 2004 November 2004 FX35/FX45
2. STEERING LOCK UNIT GROUND CIRCUIT INSPECTION
Check continuity between steering lock unit connector M26 terminal 4 (Y/B) and ground.
OK or NG
OK >> GO TO 3.
NG >> GO TO 4.
3. STEERING LOCK COMMUNICATION CIRCUIT INSPECTION
1. Connect steering lock unit connector.
2. Check voltage between Intelligent Key unit connector M34 terminal 1 (R/W) and ground.
3. Immediately after pushing ignition knob, use an oscilloscope to check voltage waveform between Intelli-
gent Key unit connector M34 terminal 32 (R/B) and ground.
OK or NG
OK >> GO TO 4.
NG >> Replace Intelligent Key unit.4 (Y/B) - Ground : Continuity should exist.
PIIA6798E
1 (R/W) - Ground : Approx. 5V
MIIB0385E
Immediately after ignition knob pushing.
32 (R/B) - Ground
MIIB0386E
SIIA1911J

INTELLIGENT KEY SYSTEM
BL-141
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: 2004 November 2004 FX35/FX45
4. STEERING LOCK UNIT COMMUNICATION CIRCUIT INSPECTION
1. Disconnect Intelligent Key unit and steering lock unit connectors.
2. Check continuity between Intelligent Key unit connector M34 terminals 1, 31, 32 and steering lock unit
connector M26 terminals 2, 3, 4.
3. Check continuity between steering lock unit connector M26 ter-
minals 2, 3, 4 and ground.
OK or NG
OK >> Replace steering lock unit.

After replacing steering lock unit, perform registration procedure. Refer to “CONSULT-II Opera-
tion Manual NATS-IVIS/NVIS”.
NG >> Repair or replace harness between steering lock unit and Intelligent Key unit.
Check Stop Lamp SwitchAIS004NM
1. STOP LAMP SWITCH POWER SUPPLY CIRCUIT INSPECTION
1. Disconnect stop lamp switch connector.
2. Check voltage between stop lamp switch connector E210 termi-
nal 1 (GY) and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace harness between stop lamp switch
and fuse.
2. STOP LAMP SWITCH OPERATION INSPECTION
Check continuity between stop lamp switch connector E210 terminal
1 and 2.
OK or NG
OK >> GO TO 3.
NG >> Replace stop lamp switch.1 (R/W) - 2 (R/W) : Continuity should exist.
31 (Y/B) - 4 (Y/B) : Continuity should exist.
32 (R/B) - 3 (R/B) : Continuity should exist.
2 (R/W) - Ground : Continuity should not exist.
3 (R/B) - Ground : Continuity should not exist.
4 (Y/B) - Ground : Continuity should not exist.
PIIA6799E
1 (GY) - Ground : Battery voltage
PIIA6811E
1 - 2
Brake pedal depressed : Continuity should exist.
Brake pedal not
depressed: Continuity should not exist.
PIIA6800E