2004 INFINITI FX35 ECU

ABCDEFGHIJKMLQUICK REFERENCE INDEX AGENERAL INFORMATIONGIGeneral InformationBENGINEEMEngine MechanicalLUEngine Lubrication SystemCOEngine Cooling SystemECEngine Control SystemFLFuel SystemEXExhaust SystemACCAccelerator Control SystemCTRANSMISSION/
TRANSAXLEATAutomatic TransmissionDDRIVELINE/AXLETFTransferPRPropeller ShaftFFDFront Final DriveRFDRear Final DriveFAXFront AxleRAXRear AxleESUSPENSIONFSUFront SuspensionRSURear SuspensionWTRoad Wheels & TiresFBRAKESBRBrake SystemPBParking Brake SystemBRCBrake Control SystemGSTEERINGPSPower Steering SystemHRESTRAINTSSBSeat BeltsSRSSupplemental Restraint System
(SRS)IBODYBLBody, Lock & Security SystemGWGlasses, Window System & Mir-
rorsRFRoofEIExterior & InteriorIPInstrument PanelSESeatJAIR CONDITIONERATCAutomatic Air ConditionerKELECTRICALSCStarting & Charging SystemLTLighting SystemDIDriver Information SystemWWWiper, Washer & HornBCSBody Control SystemLANLAN SystemAVAudio Visual, Navigation & Tele-
phone SystemACSAuto Cruise Control SystemPGPower Supply, Ground & Circuit Ele-
mentsLMAINTENANCEMAMaintenanceMINDEXIDXAlphabetical IndexEdition: July 2003
Revision: November 2004

ACCELERATOR CONTROL SYSTEM
ACC-3
C
D
E
F
G
H
I
J
K
L
MA
ACC
Revision: 2004 November 2004 FX35/FX45
ACCELERATOR CONTROL SYSTEMPFP:18005
Removal and InstallationABS005ZA
REMOVAL
1. Disconnect accelerator pedal position sensor harness connector.
2. Loosen nuts, and remove accelerator pedal assembly.
CAUTION:

Do not disassemble accelerator pedal assembly. Do not remove accelerator pedal position sen-
sor from the accelerator pedal assembly.

Avoid impact from dropping etc. during handling.

Be careful to keep the accelerator pedal assembly away from water.
INSTALLATION
Install in the reverse order of removal.
INSPECTION AFTER INSTALLATION

Check that the accelerator pedal moves smoothly within the whole operation range.

Make sure that accelerator pedal securely returns to the original position.

For the electrical inspection of accelerator pedal position sensor, refer to EC-555, "DTC P2122, P2123
APP SENSOR" (VQ35DE), EC-562, "DTC P2127, P2128 APP SENSOR" (VQ35DE) and EC-576, "DTC
P2138 APP SENSOR" (VQ35DE) or EC-1225, "DTC P2122, P2123 APP SENSOR" (VK45DE), EC-
1232, "DTC P2127, P2128 APP SENSOR" (VK45DE) and EC-1246, "DTC P2138 APP SENSOR"
(VK45DE).
CAUTION:
When harness connector of accelerator pedal position sensor is disconnected, perform “Acceler-
ator Pedal Released Position Learning”. Refer to EC-49, "
Accelerator Pedal Released Position
Learning" (VQ35DE) or EC-698, "Accelerator Pedal Released Position Learning" (VK45DE).
1. Accelerator pedal assembly
SBIA0332E

ACS-30
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: 2004 November 2004 FX35/FX45
CONSULT-II FunctionAKS006YU
DESCRIPTION
CONSULT-II executes following functions by combining data reception and command transmission via com-
munication line from ICC unit.
CONSULT-II INSPECTION PROCEDURE
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
1. Turn ignition switch OFF.
2. Connect “CONSULT-II” and “CONSULT-II CONVERTER” to
data link connector, which is located under LH dash panel near
the hood opener handle.
3. Turn ignition switch ON.
4. Touch “START (NISSAN BASED VHCL)”.
5. Touch “ICC” on the selection screen.
If “ICC” is not indicated, go to GI-40, "
CONSULT-II Data Link
Connector (DLC) Circuit" .
Test mode Function
WORK SUPPORT

Monitors aiming direction to facilitate laser beam aiming operation.

Indicates causes of automatic cancellation of the ICC system.
SELF-DIAGNOSTIC RESULTS Displays malfunctioning system memorized in ICC unit.
DATA MONITOR Displays real-time input/output data of ICC unit.
CAN DIAG SUPPORT MNTR The results of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST Enables operation check of electrical loads by sending driving signal to them.
ECU PART NUMBER Displays part number of ICC unit.
PBIB1503E
SKIA3098E
SKIA6193E

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACS-31
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
6. Touch any of “WORK SUPPORT”, “SELF-DIAG RESULTS”,
“DATA MONITOR”, “CAN DIAG SUPPORT MNTR”, “ACTIVE
TEST” and “ECU PART NUMBER” on selection screen.
WORK SUPPORT
Work Item
Cause of Auto-Cancel
1. Touch “WORK SUPPORT” on the selection screen, refer to
ACS-30, "
CONSULT-II INSPECTION PROCEDURE" .
2. Touch “CAUSE OF AUTO-CANCEL” on the selection screen.
3. Cause of automatic cancellation screen will be shown.
CAUTION:
Last five cancel (system cancel) causes are displayed.
Display Item List
Laser Beam Adjust
For details, refer to ACS-12, "LASER BEAM AIMING ADJUSTMENT" .
SELF-DIAGNOSTIC RESULTS
For details, refer to ACS-40, "Diagnostic Trouble Code (DTC) Chart" .
PKIA8867E
Operation Function
CAUSE OF AUTO-CANCEL Indicates causes of automatic cancellation of the ICC system.
LASER BEAM ADJUST Outputs laser beam, calculates dislocation of the beam, and indicates adjustment direction.
SKIA6191E
Cause of cancellation Description
OPERATING WIPER Windshield wipers were operated at HI or LO speed operation.
OPERATING ABS ABS function was operated.
OPERATING TCS TCS function was operated.
OPERATING VDC VDC function was operated.
OPE SW VOLT CIRC Outside the standard control switch input voltage was detected.
LASER SUN BEAM Intense light such as sunlight entered ICC sensor light sensing part.
LASER TEMP Temperature around ICC sensor became low.
OP SW DOUBLE TOUCH ICC steering switches were pressed at the same time.
VDC/TCS OFF SW VDC OFF switch was pressed.
WHEEL SPD UNMATCH Wheel speed became different from AT vehicle speed.
TIRE SLIP Wheel slipped.
PKB SW ON Parking brake is applied.
IGN LOW VOLT Power supply voltage became low.
NO RECORD —

ACS-32
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: 2004 November 2004 FX35/FX45
DATA MONITOR
Operation Procedure
1. Touch “DATA MONITOR” on the selection screenACS-30,
"CONSULT-II INSPECTION PROCEDURE" .
2. Touch any of “ECU INPUT SIGNALS”, “MAIN SIGNALS”, and
“SELECTION FROM MENU” on selection screen.
3. Touch “SETTING”.
4. Display the data monitor.
5. If necessary, touch “COPY” in turn, and print data.
Monitored Item
×: Applicable
PKIA8868E
Monitored Item [unit]MAIN SIG-
NALSECU
INPUT
SIGNALSSELEC-
TION
FROM
MENUDescription
VHCL SPEED SE
[km/h] or [mph]×××Indicates vehicle speed calculated from wheel speed sen-
sor signal.
SET VHCL SPD
[km/h] or [mph]××Indicates set vehicle speed memorized in ICC unit.
THRTL OPENING
[%]×××Indicates throttle angle calculated from signal voltage of
throttle position sensor.
ENGINE RPM
[rpm]××Indicates engine speed read by ICC unit via CAN commu-
nication (ECM transmits engine speed via CAN communi-
cation).
DISTANCE ADJ
[SHOR/MID/LONG]×××Indicates set distance memorized in ICC unit.
WIPER SW
[OFF/LOW/HIGH]××Indicates wiper [OFF/LOW/HIGH] status.
MAIN SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from control switch
signal.
SET/COAST SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from control switch
signal.
CANCEL SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from control switch
signal.
RESUME/ACC SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from control switch
signal.
CRUISE OPE
[ON/OFF]××Indicates whether controlling or not (ON means “control-
ling”).
BRAKE SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from ICC brake
switch signal.
STOP LAMP SW
[ON/OFF]×××Indicates [ON/OFF] status as judged from stop lamp
switch signal.
RELEASE SW NO
[ON/OFF]
××Indicates [ON/OFF] status as judged from release switch
signal.
ON when brake is depressed.
OFF when brake is not depressed.
RELEASE SW NC
[ON/OFF]
××Indicates [ON/OFF] status as judged from release switch
signal.
OFF when brake is depressed.
ON when brake is not depressed.

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACS-33
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
ACTIVE TEST
Caution

Do not perform the active test while driving.

Active test cannot be started while ICC system warning indicator illuminates.
1. Touch “ACTIVE TEST” on selection screenACS-30, "
CONSULT-II INSPECTION PROCEDURE" .
2. Touch any of “ICC BUZZER 1”, “METER LAMP”, “STOP LAMP”
and “BOOSTER SOL/V 3” on selection screen.
3. Touch necessary item and “START”.
4. Active test screen will be shown.
IDLE SW
[ON/OFF]××Indicates [ON/OFF] status of idle switch read by ICC unit
via CAN communication (ECM transmits ON/OFF status
via CAN communication).
GEAR
[1, 2, 3, 4, 5]××Indicates AT gear position read by ICC unit via CAN com-
munication (TCM transmits gear position via CAN commu-
nication).
BUZZER O/P
[ON/OFF] ×Indicates [ON/OFF] status of ICC war output.
ICC WARNING×NOTE:
This item is displayed, but cannot monitoring.
VHCL SPD AT
[km/h] or [mph]
×Indicates vehicle speed calculated from AT vehicle speed
sensor by ICC unit via CAN communication (TCM trans-
mits AT vehicle speed sensor signal via CAN communica-
tion).
PRESS SENS
[bar]×××Indicates brake fluid pressure value calculated from signal
voltage of pressure sensor.
PRESS SENS 2×NOTE:
This item is displayed, but cannot monitoring.
D RANGE SW
[ON/OFF]××Indicates [ON/OFF] status of “D” position read by ICC unit
via CAN communication (TCM transmits ON/OFF condi-
tion of “D” position via CAN communication).
AT OD OFF
[ON/OFF]×Indicates [ON/OFF] status of OD cancel output under con-
trol.
NP RANGE SW
[ON/OFF]××Indicates PNP switch signal read by ICC unit via CAN
communication. TCM transmits PNP switch signal via CAN
communication.
DISTANCE×NOTE:
This item is displayed, but cannot monitoring.
RELATIVE SPD×NOTE:
This item is displayed, but cannot monitoring.
STP LMP DRIVE
[ON/OFF]××Indicates [ON/OFF] status of brake hold relay drive output. Monitored Item [unit]MAIN SIG-
NALSECU
INPUT
SIGNALSSELEC-
TION
FROM
MENUDescription
SKIA6195E

ACS-38
[ICC]
TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
Revision: 2004 November 2004 FX35/FX45
1. CHECK ICC SYSTEM DISPLAY

When ignition switch is ON, do all displays illuminate?
YES or NO
YES >> GO TO 2.
NO >> GO TO 5.
2. CHECK ICC STEERING SWITCH

Check ICC steering switch. Refer to ACS-65, "ICC Steering Switch" .
OK or NG
OK >> GO TO 3.
NG >> Replace ICC steering switch.
3. CHECK HARNESS BETWEEN ECM AND ICC STEERING SWITCH

Check harness and spiral cable between ECM and ICC steering switch for open or short circuit.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness or spiral cable between ECM and ICC steering switch.
4. CHECK SELF-DIAGNOSIS

Disconnect connector of ECM, and check terminals for bend and looseness. Securely connect it again.

Enter self-diagnosis mode for ICC system?
YES or NO
YES >> INSPECTION END
NO >> GO TO 5.
5. CHECK POWER SUPPLY FOR ICC UNIT

Check ICC unit power supply, and repair if necessary.

When ignition switch is ON, do all displays illuminate?
YES or NO
YES >> Perform self-diagnosis again.
NO >> GO TO 6.
6. CHECK CONNECTOR FOR ICC UNIT

Disconnect connector of ICC unit, and check terminals for bend and looseness. Securely connect it again.

When ignition switch is ON, do all displays illuminate?
YES or NO
YES >> Perform self-diagnosis again.
NO >> GO TO 7.
Combination meter system malfunction Indication not possible Indicator malfunction
Indicator segments disappear.
ICC unit malfunctionOpen or short lines Trouble phenomenon Malfunction causes

ACS-42
[ICC]
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
Revision: 2004 November 2004 FX35/FX45
DTC 31 POWER SUPPLY CIR, DTC 34 POWER SUPPLY CIR 2AKS006YZ
1. CHECK CONNECTOR ICC UNIT
1. Turn ignition switch OFF.
2. Disconnect ICC unit connector, and connect it securely again. Then erase DTC. After that perform self-
diagnosis of ICC system again.
OK or NG
OK >> GO TO 2.
NG >>

Poor connector connection.

Check connector. (Check connector housing for disconnected, loose, bent, and collapsed ter-
minals. If any malfunction is detected, repair applicable part.) After repair, erase DTC, and per-
form ICC running test. Then perform self-diagnosis of ICC system again.
2. CHECK POWER SUPPLY CIRCUIT FOR ICC UNIT
1. Turn ignition switch ON.
2. Check voltage between ICC unit harness connector M89 termi-
nal 33 (G/R), 42 (G/R) and ground.
OK or NG
OK >> GO TO 3.
NG >>

Repair ICC unit power supply harness.

After repair, erase DTC and perform ICC system run-
ning test. Then, perform self-diagnosis of ICC system
again.
3. CHECK GROUND CIRCUIT FOR ICC UNIT
1. Turn ignition switch OFF.
2. Disconnect ICC unit connector.
3. Check continuity between ICC unit harness connector M88 ter-
minal 19 (B), 20 (B), M89 terminal 46 (B) and ground.
OK or NG
OK >> After replacing ICC unit, erase DTC, and perform ICC
system running test. Then perform self-diagnosis of ICC
system again.
NG >>

Repair ICC unit ground harness.

After repair, erase DTC and perform ICC system running test. Then, perform self-diagnosis of
ICC system again.
DTC 41 VHCL SPEED SE CIRCAKS006Z0
1. PERFORM ICC UNIT SELF-DIAGNOSIS
1. Perform self-diagnosis. Is “DTC 43 ABS/TCS/VDC CIRC” or “DTC 20 CAN COMM CIRCUIT” indicated in
self-diagnosis item display?
YES or NO
YES >> Repair or replace applicable item. Erase DTC and perform ICC system running test. Then perform
self-diagnosis of ICC system again.
NO >> GO TO 2Battery voltage should exist.
SKIA1173E
Continuity should exist.
SKIA6650E