2004 INFINITI FX35 parking brake

ABCDEFGHIJKMLQUICK REFERENCE INDEX AGENERAL INFORMATIONGIGeneral InformationBENGINEEMEngine MechanicalLUEngine Lubrication SystemCOEngine Cooling SystemECEngine Control SystemFLFuel SystemEXExhaust SystemACCAccelerator Control SystemCTRANSMISSION/
TRANSAXLEATAutomatic TransmissionDDRIVELINE/AXLETFTransferPRPropeller ShaftFFDFront Final DriveRFDRear Final DriveFAXFront AxleRAXRear AxleESUSPENSIONFSUFront SuspensionRSURear SuspensionWTRoad Wheels & TiresFBRAKESBRBrake SystemPBParking Brake SystemBRCBrake Control SystemGSTEERINGPSPower Steering SystemHRESTRAINTSSBSeat BeltsSRSSupplemental Restraint System
(SRS)IBODYBLBody, Lock & Security SystemGWGlasses, Window System & Mir-
rorsRFRoofEIExterior & InteriorIPInstrument PanelSESeatJAIR CONDITIONERATCAutomatic Air ConditionerKELECTRICALSCStarting & Charging SystemLTLighting SystemDIDriver Information SystemWWWiper, Washer & HornBCSBody Control SystemLANLAN SystemAVAudio Visual, Navigation & Tele-
phone SystemACSAuto Cruise Control SystemPGPower Supply, Ground & Circuit Ele-
mentsLMAINTENANCEMAMaintenanceMINDEXIDXAlphabetical IndexEdition: July 2003
Revision: November 2004

ACS-12
[ICC]
LASER BEAM AIMING ADJUSTMENT
Revision: 2004 November 2004 FX35/FX45
LASER BEAM AIMING ADJUSTMENTPFP:00026
OutlineAKS006YI
Adjust the laser beam aiming every time the ICC sensor is removed or installed.
CAUTION:

Place the vehicle on the level ground when the laser beam aiming adjustment is operated.

Follow the CONSULT-II when adjusting the Laser beam aiming (Laser beam aiming adjustment
cannot be operated without CONSULT-II).
PreparationAKS006YJ

Keep all tires inflated to correct pressures. Adjust the tire pressure to the specified pressure value.

See that there is no-load in vehicle other than the driver (or equivalent weight placed in driver's position).
Coolant, engine oil filled up to correct level and full fuel tank.

Shift the gear into “P” position and release the parking brake.

Clean the sensor with a soft cloth.
Outline of Adjustment ProcedureAKS006YK
1. Set up the ICC target board [KV99110100 (J-45718)].
2. Adjust the sensor following the procedure on CONSULT-II (Turn manually the screw for up-down position
adjustment. ICC sensor automatically adjust the right-left position.).
Setting the ICC Target BoardAKS006YL
Accurate ICC target board setting is required for the laser beam aiming adjustment.
CAUTION:
ICC system does not function normally if laser beam aiming is not accurate.
ADJUSTING HEIGHT OF THE TARGET
1. Attach a triangle scale as shown in the right figure.
SKIA6179E
SKIA5974E

ACS-28
[ICC]
TERMINALS AND REFERENCE VALUE
Revision: 2004 November 2004 FX35/FX45
Terminals and Reference Value for ICC SensorAKS006YR
33 (G/R)
42 (G/R)
GroundIgnition switch ON or
STARTON — Battery voltage (Approx.12)
38 (P/G)Stop lamp switch
(normally open) ONDepress the brake pedal. Battery voltage (Approx.12)
Release the brake pedal. Approx. 0
39
(G/OR)DDL-RX — — —
40
(PU/W)parking brake signal ONParking brake is ONPower supply voltage
(Approx. 12)
Parking brake is OFF Approx. 0
47 (W/R)Stop lamp drive output sig-
nalONBrake operating with ICC system Battery voltage (Approx.12)
Brake not operating with ICC sys-
temApprox. 0 terminals
(wire color)
itemcondition
voltage (V)
+-ignition
switchoperation
terminals
(wire color)
itemcondition
voltage (V)
+–ignition
switchoperation
1 (Y)
GroundICC sensor power ON — Battery voltage (Approx.12)
3 (L) CAN H ON — —
6 (R) CAN L ON — —
4 (B) Ground ON — Approx. 0

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION
ACS-31
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
6. Touch any of “WORK SUPPORT”, “SELF-DIAG RESULTS”,
“DATA MONITOR”, “CAN DIAG SUPPORT MNTR”, “ACTIVE
TEST” and “ECU PART NUMBER” on selection screen.
WORK SUPPORT
Work Item
Cause of Auto-Cancel
1. Touch “WORK SUPPORT” on the selection screen, refer to
ACS-30, "
CONSULT-II INSPECTION PROCEDURE" .
2. Touch “CAUSE OF AUTO-CANCEL” on the selection screen.
3. Cause of automatic cancellation screen will be shown.
CAUTION:
Last five cancel (system cancel) causes are displayed.
Display Item List
Laser Beam Adjust
For details, refer to ACS-12, "LASER BEAM AIMING ADJUSTMENT" .
SELF-DIAGNOSTIC RESULTS
For details, refer to ACS-40, "Diagnostic Trouble Code (DTC) Chart" .
PKIA8867E
Operation Function
CAUSE OF AUTO-CANCEL Indicates causes of automatic cancellation of the ICC system.
LASER BEAM ADJUST Outputs laser beam, calculates dislocation of the beam, and indicates adjustment direction.
SKIA6191E
Cause of cancellation Description
OPERATING WIPER Windshield wipers were operated at HI or LO speed operation.
OPERATING ABS ABS function was operated.
OPERATING TCS TCS function was operated.
OPERATING VDC VDC function was operated.
OPE SW VOLT CIRC Outside the standard control switch input voltage was detected.
LASER SUN BEAM Intense light such as sunlight entered ICC sensor light sensing part.
LASER TEMP Temperature around ICC sensor became low.
OP SW DOUBLE TOUCH ICC steering switches were pressed at the same time.
VDC/TCS OFF SW VDC OFF switch was pressed.
WHEEL SPD UNMATCH Wheel speed became different from AT vehicle speed.
TIRE SLIP Wheel slipped.
PKB SW ON Parking brake is applied.
IGN LOW VOLT Power supply voltage became low.
NO RECORD —

AT-4Revision: 2004 November 2004 FX35/FX45CONSULT-II Reference Value ..............................187
Diagnostic Procedure ...........................................187
TROUBLE DIAGNOSIS FOR SYMPTOMS ............188
Wiring Diagram — AT — NONDTC ......................188
A/T CHECK Indicator Lamp Does Not Come On . 191
Engine Cannot Be Started In “P” or “N” Position ..193
In “P” Position, Vehicle Moves When Pushed ......193
In “N” Position, Vehicle Moves ..............................194
Large Shock (“N” to “D” Position) .........................195
Vehicle Does Not Creep Backward In “R” Position .198
Vehicle Does Not Creep Forward In “D” Position . 201
Vehicle Cannot Be Started From D
1 .....................203
A/T Does Not Shift: D
1 → D2 ................................206
A/T Does Not Shift: D
2 → D3 ................................208
A/T Does Not Shift: D
3 → D4 ................................211
A/T Does Not Shift: D
4 → D5 ................................213
A/T Does Not Perform Lock-up ............................216
A/T Does Not Hold Lock-up Condition ..................218
Lock-up Is Not Released ......................................220
Engine Speed Does Not Return To Idle ................221
Cannot Be Changed to Manual Mode ..................222
A/T Does Not Shift: 5th gear → 4th gear ..............223
A/T Does Not Shift: 4th gear → 3rd gear ..............225
A/T Does Not Shift: 3rd gear → 2nd gear .............227
A/T Does Not Shift: 2nd gear → 1st gear .............229
Vehicle Does Not Decelerate By Engine Brake ....231
SHIFT CONTROL SYSTEM ....................................233
Control Device Removal and Installation ..............233
Adjustment of A/T Position ...................................234
Checking of A/T Position ......................................234
A/T SHIFT LOCK SYSTEM .....................................235
Description ............................................................235
Shift Lock System Electrical Parts Location .........235
Wiring Diagram — AT — SHIFT ...........................236
Diagnostic Procedure ...........................................237
KEY INTERLOCK CABLE ......................................239
Components .........................................................239
Removal and Installation ......................................240
ON-VEHICLE SERVICE ..........................................242
Control Valve with TCM and A/T Fluid Temperature
Sensor 2 ...............................................................242
Parking Components (2WD Models Only) ............253Rear Oil Seal .........................................................259
Revolution Sensor Components (2WD Models
Only) .....................................................................260
AIR BREATHER HOSE ...........................................264
Removal and Installation .......................................264
TRANSMISSION ASSEMBLY .................................266
Removal and Installation (2WD Models) ...............266
Removal and Installation (AWD models) ..............269
OVERHAUL .............................................................274
Components ..........................................................274
Oil Channel ...........................................................282
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings ..........................284
DISASSEMBLY .......................................................286
Disassembly ..........................................................286
REPAIR FOR COMPONENT PARTS ......................303
Oil Pump ...............................................................303
Front Sun Gear, 3rd One-Way Clutch ...................306
Front Carrier, Input Clutch, Rear Internal Gear .....308
Mid Sun Gear, Rear Sun Gear, High and Low
Reverse Clutch Hub ..............................................314
High and Low Reverse Clutch ..............................320
Direct Clutch .........................................................323
ASSEMBLY .............................................................325
Assembly (1) .........................................................325
Adjustment ............................................................338
Assembly (2) .........................................................341
SERVICE DATA AND SPECIFICATIONS (SDS) ....348
General Specifications ..........................................348
Vehicle Speed When Shifting Gears .....................348
Vehicle Speed When Performing and Releasing
Complete Lock-up .................................................349
Vehicle Speed When Performing and Releasing
Slip Lock-up ..........................................................349
Stall Speed ............................................................350
Line Pressure ........................................................350
A/T Fluid Temperature Sensor ..............................350
Turbine Revolution Sensor ....................................350
Vehicle Speed Sensor A/T (Revolution Sensor) ...350
Reverse Brake ......................................................350
Total End Play .......................................................351

AT-12
A/T FLUID
Revision: 2004 November 2004 FX35/FX45
A/T FLUIDPFP:KLE40
Changing A/T FluidACS0079Z
1. Warm up ATF.
2. Stop engine.
3. Loosen the level gauge bolt.
4. Drain ATF from drain plug and refill with new ATF. Always refill
same volume with drained fluid.

To replace the ATF, pour in new fluid at the charging pipe with
the engine idling and at the same time drain the old fluid from
the radiator cooler hose return side.

When the color of the fluid coming out is about the same as
the color of the new fluid, the replacement is complete. The
amount of new transmission fluid to use should be 30 to 50%
increase of the stipulated amount.
CAUTION:

Use only Genuine Nissan Matic J ATF. Do not mix with other fluid.

Using automatic transmission fluid other than Genuine Nissan Matic J ATF will cause deteriora-
tion in drive ability and automatic transmission durability, and may damage the automatic trans-
mission, which is not covered by the warranty.

When filling ATF, take care not to splash heat generating parts such as exhaust with ATF.

Do not reuse drain plug gasket.
5. Run engine at idle speed for 5 minutes.
6. Check fluid level and condition. Refer to AT- 1 2 , "
Checking A/T Fluid" . If fluid is still dirty, repeat step 2
through 5.
7. Install the removed A/T fluid level gauge in the A/T fluid charging pipe.
8. Tighten the level gauge bolt.
Checking A/T FluidACS007A0
1. Warm up engine.
2. Check for fluid leakage.
3. Loosen the level gauge bolt.
4. Before driving, fluid level can be checked at fluid temperatures
of 30 to 50°C (86 to 122°F) using “COLD” range on A/T fluid
level gauge as follows.
a. Park vehicle on level surface and set parking brake.
b. Start engine and move selector lever through each gear posi-
tion. Leave selector lever in “P” position.
c. Check fluid level with engine idling.
d. Remove A/T fluid level gauge and wipe clean with lint-free
paper.
CAUTION:
When wiping away the A/T fluid level gauge, always use
lint-free paper, not a cloth one.A/T fluid: Genuine Nissan Matic J ATF
Fluid capacity: 10.3 (10-7/8 US qt, 9-1/8 lmp qt)
Drain plug:
: 34 N·m (3.5 kg-m, 25 ft-lb)
Level gauge bolt:
: 5.1 N·m (0.52 kg-m, 45 in-lb)
SCIA4896E
SCIA4835E

A/T CONTROL SYSTEM
AT-19
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
Shift MechanismACS002LE
The automatic transmission uses compact triple planetary gear systems to improve power-transmission effi-
ciency, simplify construction and reduce weight.
It also employs an optimum shift control and super wide gear ratios. They improve starting performance and
acceleration during medium and high-speed operation.
CONSTRUCTION
FUNCTION OF CLUTCH AND BRAKE
1. Front brake 2. Input clutch 3. Direct clutch
4. High and low reverse clutch 5. Reverse brake 6. Forward brake
7. Low coast brake 8. 1st one-way clutch 9. Forward one-way clutch
10. 3rd one-way clutch 11. Front sun gear 12. Input shaft
13. Mid internal gear 14. Front internal gear 15. Rear carrier
16. Rear sun gear 17. Mid sun gear 18. Front carrier
19. Mid carrier 20. Rear internal gear 21. Output shaft
22. Parking gear 23. Parking pawl
PCIA0002J
Name of the Part Abbreviation Function
Front brake (1) FR/B Fastens the front sun gear (11).
Input clutch (2) I/CConnects the input shaft (12), the front internal gear (14) and the mid internal
gear (13).
Direct clutch (3) D/C Connects the rear carrier (15) and the rear sun gear (16).
High and low reverse clutch (4) HLR/C Connects the mid sun gear (17) and the rear sun gear (16).
Reverse brake (5) R/B Fastens the rear carrier (15).
Forward brake (6) Fwd/B Fastens the mid sun gear (17).
Low coast brake (7) LC/B Fastens the mid sun gear (17).
1st one-way clutch (8) 1st/owcAllows the rear sun gear (16) to turn freely forward relative to the mid sun gear
(17) but fastens it for reverse rotation.
Forward one-way clutch (9) F/owcAllows the mid sun gear (17) to turn freely in the forward direction but fastens it
for reverse rotation.
3rd one-way clutch (10) 3rd/owcAllows the front sun gear (11) to turn freely in the forward direction but fastens
it for reverse rotation.

A/T CONTROL SYSTEM
AT-21
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
POWER TRANSMISSION
“N” Position
Since both the forward brake and the reverse brake are released, torque from the input shaft drive is not trans-
mitted to the output shaft.
“P” Position

The same as for the “N” position, both the forward brake and the reverse brake are released, so torque
from the input shaft drive is not transmitted to the output shaft.

The parking pawl linked with the selector lever meshes with the parking gear and fastens the output shaft
mechanically.
1. Front brake 2. Input clutch 3. Direct clutch
4. High and low reverse clutch 5. Reverse brake 6. Forward brake
7. Low coast brake 8. 1st one-way clutch 9. Forward one-way clutch
10. 3rd one-way clutch 11. Front sun gear 12. Input shaft
13. Mid internal gear 14. Front internal gear 15. Rear carrier
16. Rear sun gear 17. Mid sun gear 18. Front carrier
19. Mid carrier 20. Rear internal gear 21. Output shaft
22. Parking gear 23. Parking pawl
PCIA0003J