2004 DAEWOO NUBIRA fuel

1F – 42IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
191. Measure the resistance between following ter-
minals:
S Terminal 1 and 2 of ignition coil.
S Terminal 2 and 1 of ignition coil.
Are the resistance within the value specified.
1. Remove the high tension cable.
2. Measure the resistance between second coil.
S Between 1 and 4
S Between 2 and 3
Are the resistance within the value specified.0.9 W
5.3 kWGo to Step 21Go to Step 20
20Replace the EI system ignition coil.
Is the repair complete?–Go to Step 2–
211. Check for any damages or poor connection in
ignition wires and repair as needed.
2. Connect the EI system ignition coil connector
and ECM connector.
3. Check for the presence of spark from all of the
ignition wires.
Is the spark present from all of the ignition wires?–Go to Step 2Go to Step 22
22Replace ECM.
Is the repair complete?–Go to Step 2–
231. Turn the ignition OFF.
2. Connect a fuel pressure gauge.
3. Crank the engine.
Is any fuel pressure present?–Go to Step 26Go to Step 24
241. Turn the ignition OFF.
2. Disconnect the electrical connector at the fuel
pump.
3. Connect a test light between the fuel pump ter-
minals 2 and 3.
4. Turn the ignition ON.
5. With the ignition ON, the test light should light
for the time specified.
Is the test light on?2 sec.Go to Step 25Go to 34
25Replace the fuel pump.
Is the repair complete?–Go to Step 2–
26Is the fuel pressure within the value specified?283–324 kPa
(41–47 psi)Go to Step 27Go to Step 29
27Check the fuel for contamination.
Is the fuel contaminated?–Go to Step 28Go to Step 41
281. Remove the contaminated fuel from the fuel
tank.
2. Clean the fuel tank as needed.
Is the repair complete?–Go to Step 2–
291. Check the fuel filter for restriction.
2. Inspect the fuel lines for kinks and restrictions.
3. Repair or replace as needed.
4. Measure the fuel pressure.
Is the fuel pressure within the value specified?283–324 kPa
(41–47 psi)Go to Step 2Go to Step 30

ENGINE CONTROLS 1F – 43
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
301. Disconnect vacuum line from the fuel pressure
regulator.
2. Inspect the vacuum line for the presence of
fuel.
3. Inspect the fuel pressure regulator vacuum port
for the presence of fuel.
Is any fuel present?–Go to Step 31Go to Step 32
31Replace the fuel pressure regulator.
Is the repair complete?–Go to Step 2–
321. Remove the fuel pump assembly from the fuel
tank.
2. Inspect the fuel pump sender and the fuel cou-
pling hoses for a restriction.
3. Inspect the in–tank fuel filter for restriction.
Is the problem found?–Go to Step 33Go to Step 25
33Replace the fuel pump sender, the in–tank fuel filter,
and/or the fuel coupling hoses as needed.
Is the repair complete?–Go to Step 2–
341. Turn the ignition OFF.
2. Disconnect the electric connector at the fuel
pump.
3. Connect a test light between fuel pump con-
nector terminal 3 and ground.
4. Turn the ignition ON.
5. With the ignition ON, the test light should illumi-
nate for the time specified.
Is the test light on?2 secGo to Step 35Go to Step 36
35Repair the open circuit between the fuel pump con-
nector terminal 2 and ground.
Is the repair complete?–Go to Step 2–
361. Turn the ignition OFF.
2. Disconnect the fuel pump relay.
3. Turn the ignition ON.
4. Measure the voltage at terminal 30 and 86 of
fuel pump relay.
Is the voltage within the value specified?11–14 VGo to Step 38Go to Step 37
37Repair open or short circuit for power supply.
Is the repair complete?–Go to Step 2–
381. Turn the ignition OFF.
2. Disconnect ECM connector.
3. Using an ohmmeter, measure the resistance
between following terminals.
S Terminal 6 of ECM and terminal 85 of fuel
pump relay.
S Terminal 87 of fuel pump relay and terminal
3 of fuel pump.
Does the resistance within the value specified?0 WGo to Step 40Go to Step 39

1F – 44IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
39Repair the open or short circuit the following termi-
nals.
S Terminal 6 of ECM and terminal 86 of fuel
pump relay.
S Terminal 87 of fuel pump relay and terminal
3 of fuel pump.
Is the repair complete?–Go to Step 2–
40Replace the fuel pump relay.
Is the repair complete?–Go to Step 2–
411. Turn the ignition OFF.
2. Disconnect the fuel inject harness connectors
from all of the fuel injectors.
3. Turn the ignition ON.
4. Connect test light between fuel injector harness
connector 2 and ground.
5. Repeat step 4 for each of the remaining fuel
injectors.
Does the test light on at all of the fuel injectors?–Go to Step 42Go to Step 45
421. Turn the ignition OFF.
2. Connect test light between fuel injector harness
connector 1 and battery positive.
3. Crank the engine.
4. Repeat step 2 and 3 for each of the remaining
fuel injectors.
Does the test light flash for all of the fuel injectors?–Go to Step 43Go to Step 46
43Measure the resistance of each fuel injectors.
Is the resistance within the value specified.
Notice : the resistance will increase slightly at higher
temperature.11.6–12.4WSystem OKGo to Step 44
44Replace any of the fuel injectors with a resistance
out of specification.
Is the repair complete?–Go to Step 2–
451. Inspect the fuse EF22 in engine fuse block.
2. Check for an open between the circuit from
terminal 2 of the four fuel injectors and terminal
87 of main relay.
Is the problem found?–Go to Step 48Go to
”Main Relay
Circuit Check”
46Measure the resistance between following termi-
nals.
S Terminal 2 of injector 1 connector and terminal
59 of ECM connector.
S Terminal 2 of injector 2 connector and terminal
90 of ECM connector.
S Terminal 2 of injector 3 connector and terminal
60 of ECM connector.
S Terminal 2 of injector 4 connector and terminal
89 of ECM connector.
Does the resistance within the specified value?0 WGo to Step 49Go to Step 47
47Repair the open fuel injector harness wire(s).
Is the repair complete?–Go to Step 2–

ENGINE CONTROLS 1F – 47
DAEWOO V–121 BL4
ENGINE CRANKS BUT WILL NOT RUN (1.8L DOHC)
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the occurred. The information is then stored on the
scan tool for later reference.
2. By performing a compression test, it can be deter-
mined if the engine has the mechanical ability to
run.
3. It is important to check for the presence of sparkfrom all of the ignition wires. If spark is present from
one to three of the ignition coil terminals, the Crank-
shaft Position (CKP) sensor is OK.
19. In checking the engine control module (ECM) out-
puts for the electronic spark timing signal, it recom-
mended to use an oscilloscope to view the varying
voltage signals. In measuring these outputs with a
voltmeter, intermittent errors may occur that cannot
be seen by a voltmeter.
35. This step checks for proper operation of the ECM’s
control of the fuel pump circuit.
59. This step checks for a ground signal being supplied
by the ECM to operate the fuel injectors. If there is
no ground present during the cranking of the en-
gine, and the fuel injector wiring is OK, the ECM is
at fault.
Engine Cranks But Will Not Run (1.8L DOHC)
CAUTION : Use only electrically insulated pliers when
handling ignition wires with the engine running to
prevent an electrical shock.
CAUTION : Do not pinch or restrict nylon fuel lines.Damage to the lines could cause a fuel leak, resulting
in possible fire or personal injury.
Step
ActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic
(EOBD) Sys-
tem Check”
2Check for set Diagnostic Trouble Code (DTC)
P0601.
Is the DTC set?–Go to applica-
ble DTC tableGo to Step 4
3Crank the engine.
Does the engine start and continue to run?–System OKGo to Step 5
4Perform a cylinder compression test.
Is the cylinder compression for all of the cylinders at
or above the value specified?689 kPa
(100 psi)Go to Step 8Go to Step 5
5Inspect the timing belt alignment.
Is the timing belt in alignment?–Go to Step 7Go to Step 6
6Align or replace the timing belt as needed.
Is the repair complete?–Go to Step 3–
7Repair the internal engine damage as needed.
Is the repair complete?–Go to Step 3–
8Inspect the fuel pump fuse.
Is the problem found?–Go to Step 9Go to Step 10
9Replace the fuse.
Is the repair complete?–Go to Step 3–
101. Install a scan tool.
2. Turn the ignition ON, the engine OFF and close
the throttle.
Does the Throttle Position (TP) sensor read less
than the specified value.1.0 vGo to Step 11Go to ”DTC
P0123 Throttle
Position Sensor
High Voltage”

1F – 50IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
35While cranking the engine, measure the voltage at
the EI system ignition coil connector terminal 3 .
Does the voltage fluctuate within the values speci-
fied?0.2–2.0 vGo to Step 39Go to Step 37
36Check for an open in the wire from the EI system
ignition coil connector terminal 1 to the ECM connec-
tor terminal M51.
Is the problem found?–Go to Step 38Go to Step 40
37Check for an open in the wire from the EI system
ignition coil connector terminal 3 to the ECM connec-
tor terminal M1.
Is the problem found?–Go to Step 38Go to Step 40
381. Repair the wiring as needed.
2. Connect the EI system ignition coil connector.
3. Check for the presence of spark from all of the
ignition wires.
Is spark present from all of the ignition wires?–Go to Step 3Go to Step 39
39Replace the EI system ignition coil.
Is the repair complete?–Go to Step 3–
401. Turn the ignition OFF.
2. Replace the ECM.
Is the repair complete?–Go to Step 3–
411. Turn the ignition OFF.
2. Connect a fuel pressure gauge.
3. Crank the engine.
Is any fuel pressure present?–Go to Step 44Go to Step 42
421. Turn the ignition OFF.
2. Disconnect the electrical connector at the fuel
pump.
3. Connect a test light between the fuel pump
connector terminals 3 and 2.
4. Turn the ignition ON.
5. With the ignition ON, the test light should light
for the time specified.
Is the test light on?2 secGo to Step 43Go to Step 53
43Replace the fuel pump.
Is the repair complete?–Go to Step 3–
44Is the fuel pressure within the value specified?283–324 kPa
(41–47 psi)Go to Step 48Go to Step 45
451. Check the fuel filter for a restriction.
2. Inspect the fuel lines for kinks and restrictions.
Is the problem found?–Go to Step 46Go to Step 47
461. Disconnect the vacuum line from the fuel pres-
sure regulator.
2. Inspect the vacuum line for the presence of
fuel.
3. Inspect the fuel pressure regulator vacuum port
for the presence of fuel.
Is any fuel present?283–324 kPa
(41–47 psi)Go to Step 3Go to Step 47

ENGINE CONTROLS 1F – 51
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
471. Disconnect the vacuum line from the fuel pres-
sure regulator.
2. Inspect the vacuum line for the presence of
fuel.
3. Inspect the fuel pressure regulator vacuum port
for the presence of fuel.
Is any fuel presen–Go to Step 50Go to Step 51
48Check the fuel for contamination.
Is the fuel contaminated?–Go to Step 49Go to Step 65
491. Remove the contaminated fuel from the fuel
tank.
2. Clean the fuel tank as needed.
Is the repair complete?–Go to Step 3–
50Replace the fuel pressure regulator.
Is the repair complete?–Go to Step 3–
511. Remove the fuel pump assembly from the fuel
tank.
2. Inspect the fuel pump sender and the fuel cou-
pling hoses for a restriction.
3. Inspect the in–tank fuel filter for a restriction.
Is the problem found?–Go to Step 52Go to Step 43
52Replace the fuel pump sender, the in–tank fuel filter,
and/or the fuel coupling hoses as needed.
Is the repair complete?–Go to Step 3–
531. Turn the ignition OFF.
2. Disconnect the electrical connector at the fuel
pump.
3. Connect a test light between the fuel pump
connector terminal 3 and a known good
ground.
4. Turn the ignition ON.
5. With the ignition ON, the test light should light
for the time specified.
Is the test light on?2 secGo to Step 54Go to Step 55
54Repair the open wire between the fuel pump connec-
tor terminal 2 and ground.
Is the repair complete–Go to Step 3–
551. Turn the ignition OFF.
2. Disconnect the fuel pump relay.
3. Connect a test light between the fuel pump
relay connector terminal 85 and ground.
4. Turn the ignition ON.
Is the test light on?2 secGo to Step 56Go to Step 62
561. Turn the ignition OFF.
2. Connect a test light between the fuel pump
relay connector terminal 86 and battery posi-
tive.
3. Turn the ignition ON.
4. With the ignition ON, the test light should light
for the time specified.
Is the test light on?–Go to Step 57Go to Step 61

1F – 52IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
571. Turn the ignition OFF.
2. Connect a test light between the fuel pump
relay connector terminal 30 and ground.
Is the test light on?–Go to Step 58Go toStep 63
581. Turn the ignition OFF.
2. Check the wire between the fuel pump relay
connector terminal 87 and the fuel pump con-
nector terminal 3 for an open or short to
ground.
Is the repair complete?–Go to Step 2–
59Replace the fuel pump relay.
Is the repair complete?–Go to Step 3–
601. Check for an open in the wiring between the
fuel pump relay connector terminal 86 and
ground.
Is the problem found?–Go to Step 71–
61Check the wire between the fuel pump relay connec-
tor terminal 85 to the ECM connector terminal K54
for an open.
Is the problem found?–Go to Step 62Go to Step 40
62Repair the wire between the fuel pump relay connec-
tor terminal 85 to the ECM connector terminal K54.
Is the repair complete?–Go to Step 3–
63Repair the wire between the fuel pump relay connec-
tor terminal 30 and the fuse Ef18.
Is the repair complete?–Go to Step 3–
641. Turn the ignition OFF.
2. Disconnect the fuel injector harness connectors
from all of the fuel injectors.
3. Turn the ignition ON.
4. Connect a test light between the fuel injector
harness connector 2 and ground.
5. Repeat step 4 for each of the remaining fuel
injectors.
Is the test light on at all of the fuel injectors?–Go to Step 65Go to Step 68
651. Turn the ignition OFF.
2. Connect a test light between the fuel injector
harness connector terminal 1 and battery posi-
tive.
3. Crank the engine.
4. Repeat steps two and three for each of the re-
maining fuel injectors.
Does the test light flash for all of the fuel injectors?–Go to Step 66Go to Step 69
66Measure the resistance of each fuel injector.
Is the resistance within the value specified (the re-
sistance will increase slightly at higher tempera-
tures)?11.6–12.4 WSystem OKGo to Step 67
67Replace any of the fuel injectors with a resistance
out of specification.
Is the repair complete?–Go to Step 3–

ENGINE CONTROLS 1F – 53
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
68Repair the open wire(s) between the fuel injector
harness connector(s) terminal 2 and the engine har-
ness C103 terminal 10.
Is the repair complete?–Go to Step 3–
691. Check for an open between the #1 fuel injector
harness connector terminal 1 and the connec-
tor terminal M25.
2. Check for an open between the #2 fuel injector
harness connector terminal 1 and the connec-
tor terminal M22.
3. Check for an open between the #3 fuel injector
harness connector terminal 1 and the connec-
tor terminal M24.
4. Check for an open between the #4 fuel injector
harness connector terminal 1 and the connec-
tor terminal M11.
Is the problem found?–Go to Step 70Go to Step 72
70Repair the open fuel injector harness wire(s).
Is the repair complete?–Go to Step 3–
71Replace the fuse or repair the wiring as needed.
Is the repair complete?–Go to Step 3–
721. Inspect the I/P fuse F2.
2. Check for an open between the circuits from
terminal 2 for each of the four fuel injectors and
the ignition switch.
Is the problem found?–Go to Step 71–