2004 DAEWOO LACETTI light

1F – 66IENGINE CONTROLS
DAEWOO V–121 BL4
Fuel Pump Relay Circuit Check (1.4L/1.6L DOHC)
StepActionValue(s)YesNo
11. Turn the ignition OFF for 10 seconds.
2. Turn the ignition ON.
3. Listen for in–tank fuel pump operation.
Does the fuel pump operate for the time specified?2 secSystem OKGo to Step 2
21. Turn the ignition OFF.
2. Disconnect the fuel pump relay.
3. Connect a test light between the fuel pump
relay connector terminal 30 and ground.
Turn the ignition ON. Is the test light on?–Go to Step 3Go to Step 8
31. Turn the ignition OFF.
2. Connect a test light between the fuel pump
relay connector terminal 86 and battery posi-
tive.
3. Turn the ignition ON.
4. With the ignition ON, the test light should light
for the time specified.
Is the test light on?2 secGo to Step 4Go to Step 9
41. Turn the ignition OFF.
2. Connect a test light between the fuel pump
relay connector terminal 30 and ground.
Is the test light on?–Go to Step 5Go to Step 11
5Check for an open or short to ground in the wire be-
tween the fuel pump relay connector terminal 87 and
the fuel pump connector terminal 3.
Is the problem found?–Go to Step 6Go to Step 7
61. Repair the wire between the fuel pump relay
connector terminal 87 and the fuel pump con-
nector terminal 3.
2. Install the fuel pump relay.
3. Turn the ignition OFF for 10 seconds.
4. Turn the ignition ON.
Does the fuel pump operate for the time specified?2 secSystem OK–
71. Replace the fuel pump relay.
2. Turn the ignition OFF for 10 seconds.
3. Turn the ignition ON.
Does the fuel pump operate for the time specified?2 secSystem OK–
8Check for an open wire between the fuel pump relay
connector terminal 30 and the battery.
Is the problem found?–Go to Step 13–
9Check for an open wire between the fuel pump relay
connector terminal 86 to the engine control module
(ECM) connector terminal 6.
Is the problem found.–Go to Step 10Go to Step 12
101. Repair the wire between the fuel pump relay
connector terminal 86 to the ECM connector
terminal 6.
2. Install the fuel pump relay.
3. Turn the ignition OFF for 10 seconds.
4. Turn the ignition ON.
Does the fuel pump operate for the time specified?2 secSystem OK–

ENGINE CONTROLS 1F – 69
DAEWOO V–121 BL4
Fuel Pump Relay Circuit Check (1.8L DOHC)
StepActionValue(s)YesNo
11. Turn the ignition OFF for 10 seconds.
2. Turn the ignition ON.
3. Listen for in–tank fuel pump operation.
Does the fuel pump operate for the time specified?2 secSystem OKGo to Step 2
21. Turn the ignition OFF.
2. Disconnect the fuel pump relay.
3. Connect a test light between the fuel pump
relay connector terminal 30 and ground.
Turn the ignition ON. Is the test light on?–Go to Step 3Go to Step 8
31. Turn the ignition OFF.
2. Connect a test light between the fuel pump
relay connector terminal 85 and battery posi-
tive.
3. Turn the ignition ON.
4. With the ignition ON, the test light should light
for the time specified.
Is the test light on?2 secGo to Step 4Go to Step 9
41. Turn the ignition OFF.
2. Connect a test light between the fuel pump
relay connector terminal 30 and ground.
Is the test light on?–Go to Step 5Go to Step 11
5Check for an open or short to ground in the wire be-
tween the fuel pump relay connector terminal 87 and
the fuel pump connector terminal 3.
Is the problem found?–Go to Step 6Go to Step 7
61. Repair the wire between the fuel pump relay
connector terminal 87 and the fuel pump con-
nector terminal 3.
2. Install the fuel pump relay.
3. Turn the ignition OFF for 10 seconds.
4. Turn the ignition ON.
Does the fuel pump operate for the time specified?2 secSystem OK–
71. Replace the fuel pump relay.
2. Turn the ignition OFF for 10 seconds.
3. Turn the ignition ON.
Does the fuel pump operate for the time specified?2 secSystem OK–
8Check for an open wire between the fuel pump relay
connector terminal 30 and the battery.
Is the problem found?–Go to Step 13–
9Check for an open wire between the fuel pump relay
connector terminal 85 to the engine control module
(ECM) connector terminal K54
Is the problem found.–Go to Step 10Go to Step 12
101. Repair the wire between the fuel pump relay
connector terminal 85 to the ECM connector
terminal K54.
2. Install the fuel pump relay.
3. Turn the ignition OFF for 10 seconds.
4. Turn the ignition ON.
Does the fuel pump operate for the time specified?2 secSystem OK–

ENGINE CONTROLS 1F – 71
DAEWOO V–121 BL4
MAIN RELAY CIRCUIT CHECK (1.4L/1.6L DOHC)
Circuit Description
When the ignition is turned On or to the START position,
the main relay is energized. The main relay then supply
voltage to the engine fuse block fuse Ef11. The Electronic
Ignition (EI) system ignition coil, Evaporative Emission
(EVAP) Canister Purge Solenoid and Heated Oxygen
Sensor (HO2S) are supplied voltage through the engine
fuse block fuse Ef11. The fuel injectors are supplied volt-
age through the engine fuse block fuse Ef11.Diagnostic Aids
S An intermittent problem may be caused by a poor
connection, rubbed through wire insulation, or a
broken wire inside the insulation.
S A fault main relay will cause a no start condition.
There will be no voltage supplied to the EI system
ignition coil, or the fuel injectors. Without voltage
supplied to these components, they will not oper-
ate.
Main Relay Circuit Check (1.4L/1.6L DOHC)
StepActionValue(s)YesNo
11. Turn the ignition OFF.
2. Disconnect the engine fuse block fuse Ef11.
3. Turn the ignition ON.
4. With a test light connected to the ground,
probe the fuse terminals nearest the main relay
for fuse Ef11.
Is the light on at both terminal?–System OKGo to Step 2
2Is the light on at only one terminal?–Go to Step 3Go to Step 4
3Repair the open in the wiring between the main relay
connector terminal 87 and the fuse Ef11.
Is the repair complete?–System OK–

1F – 72IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
41. Turn the ignition OFF.
2. Remove the main relay.
3. Turn the ignition ON.
4. With a test light connected to the ground,
probe the main relay terminals 85.
Is the light on at both terminals.–Go to Step 6Go to Step 5
51. Turn the ignition OFF.
2. Measure the resistance between following ter-
minals.
S Terminal 86 of main relay and ground.
Is the resistance within the specified value0 WGo to Step 7Go to Step 6
6Repair open circuit.
Is the repair complete?–System OK–
7Replace the main relay.
Is the repair complete?–System OK–

ENGINE CONTROLS 1F – 73
DAEWOO V–121 BL4
MAIN RELAY CIRCUIT CHECK (1.8L DOHC)
Circuit Description
When the ignition is turned On or to the START position,
the main relay is energized. The main relay then supply
voltage to the engine fuse block fuse F2. The Electronic
Ignition (EI) system ignition coil, Evaporative Emission
(EVAP) Canister Purge Solenoid and Heated Oxygen
Sensor (HO2S) are supplied voltage through the engine
fuse block fuse F2. The fuel injectors are supplied voltage
through the engine fuse block fuse F2.Diagnostic Aids
S An intermittent problem may be caused by a poor
connection, rubbed through wire insulation, or a
broken wire inside the insulation.
S A fault main relay will cause a no start condition.
There will be no voltage supplied to the EI system
ignition coil, or the fuel injectors. Without voltage
supplied to these components, they will not oper-
ate.
Main Relay Circuit Check (1.8L DOHC)
StepActionValue(s)YesNo
11. Turn the ignition OFF.
2. Disconnect the I/P fuse block fuse F2.
3. Turn the ignition ON.
4. With a test light connected to the ground,
probe the fuse terminals nearest the ignition
relay for fuse F2.
Is the light on at both terminal?–System OKGo to Step 2
2Is the light on at only one terminal?–Go to Step 3Go to Step 4
3Repair the open in the wiring between the ignition
relay connector terminal 87 and the fuse F2.
Is the repair complete?–System OK–

1F – 74IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
41. Turn the ignition OFF.
2. Remove the ignition relay.
3. Turn the ignition ON.
4. With a test light connected to the ground,
probe the ignition relay terminals 85.
Is the light on at both terminals.–Go to Step 6Go to Step 5
51. Turn the ignition OFF.
2. Measure the resistance between following ter-
minals.
S Terminal 86 of main relay and ground.
Is the resistance within the specified value0 WGo to Step 7Go to Step 6
6Repair open circuit.
Is the repair complete?–System OK–
7Replace the ignition relay.
Is the repair complete?–System OK–

ENGINE CONTROLS 1F – 87
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
16Check the wire between the CKP sensor connector
terminal 1 and the ECM connector terminal 85 for an
open or short.
Is the problem found?Go to Step 18Go to Step 11
17Check the wire between the CKP sensor connector
terminal 3 and ground for an open or short.
Is the problem found?–Go to Step 19Go to Step 11
18Repair the wire between the CKP sensor connector
terminal 1 and the ECM connector terminal 85.
Is the repair complete?–System OK–
19Repair the wire between the CKP sensor connector
terminal 3 and ground.
Is the repair complete?–System OK–
201. Turn the ignition ON.
2. Measure the voltage between the CKP sensor
connector terminals 2 and 3.
Is the voltage within the value specified?1.3–1.5 v
(2.4–2.7 v)*Go to Step 24Go to Step 21
21Measure the voltage between the CKP sensor con-
nector terminal 2 and ground.
Is the voltage within the value specified?1.3–1.5 v
(2.4–2.7 v)*Go to Step 17Go to Step 22
22Check the wire between the CKP sensor connector
terminal 2 and the ECM connector terminal 54 for an
open or short.
Is the problem found?–Go to Step 23Go to Step 11
23Repair the wire between the CKP sensor connector
terminal 2 and the ECM connector terminal 54.
Is the repair complete?–System OK–
241. Turn the ignition OFF.
2. Connect a test light between the EI system
ignition coil connector terminal 2 and ground.
3. Turn the ignition ON.
Is the test light on?–Go to Step 25Go to Step 26
25Connect a test light between the EI system ignition
coil connector terminal 2 and battery positive.
Is the test light on?–Go to Step 5Go to Step 27
26Check for an open or short to ground in the wiring be-
tween the EI system ignition coil connector, terminal
2 and the ignition switch.
Is the problem found?–Go to Step 29–
27Repair the wire between the EI system ignition coil
connector terminal 1 and ground.
Is the repair complete?–System OK–
281. Turn the ignition OFF.
2. Replace the CKP sensor.
Is the repair complete?–System OK–
29Replace the fuse F2 or repair the open in the wiring
between the EI system ignition coil connector termi-
nal 2 and the ignition switch.
Is the repair complete?–System OK–

ENGINE CONTROLS 1F – 91
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
21Measure the voltage between the CKP sensor con-
nector terminal 2 and ground.
Is the voltage within the value specified?1.3–1.5 v
(2.4–2.7 v)*Go to Step 17Go to Step 22
22Check the wire between the CKP sensor connector
terminal 2 and the ECM connector terminal M5 for
an open or short.
Is the problem found?–Go to Step 23Go to Step 11
23Repair the wire between the CKP sensor connector
terminal 2 and the ECM connector terminal M5.
Is the repair complete?–System OK–
241. Turn the ignition OFF.
2. Connect a test light between the EI system
ignition coil connector terminal 2 and ground.
3. Turn the ignition ON.
Is the test light on?–Go to Step 25Go to Step 26
25Connect a test light between the EI system ignition
coil connector terminal 2 and battery positive.
Is the test light on?–Go to Step 5Go to Step 27
26Check for an open or short to ground in the wiring be-
tween the EI system ignition coil connector, terminal
2 and the ignition switch.
Is the problem found?–Go to Step 29–
27Repair the wire between the EI system ignition coil
connector terminal 1 and ground.
Is the repair complete?–System OK–
281. Turn the ignition OFF.
2. Replace the CKP sensor.
Is the repair complete?–System OK–
29Replace the fuse Ef10 or repair the open in the wiring
between the EI system ignition coil connector termi-
nal 2 and the ignition switch.
Is the repair complete?–System OK–