2004 DAEWOO LACETTI light

1F – 94IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
31. Check the engine fuse block fuse Ef6 and Ef8.
2. Replace the fuse as needed.
Is the fuse OK?–Go to Step 4Go to
”Diagnostic
Aids”
41. Turn the ignition OFF.
2. Turn the A/C switch OFF.
3. Connect a scan tool to the data link connector
(DLC).
4. The cooling fans should run at low speed when
the coolant temperature reaches 97°C
(207°F).
Do the cooling fans run at low speed?–Go to Step 5Go to Step 10
51. Turn the ignition OFF.
2. Turn the A/C switch OFF.
3. Connect a scan tool to the DLC.
4. Start the engine.
5. The cooling fans should run at high speed
when the coolant temperature reaches 101°C
(214°F).
Do the cooling fans run at high speed?–Go to Step 6Go to Step 33
61. Turn the ignition OFF.
2. Start the engine.
3. Turn the A/C switch ON.
Does the A/C compressor clutch engage?–Go to Step 8Go to Step 7
71. Diagnose the A/C compressor clutch circuit.
2. Repair the A/C compressor clutch circuit as
needed.
3. Start the engine.
4. Turn the A/C switch ON.
Does the A/C compressor clutch engage?–Go to Step 8–
8Do the cooling fans run at low speed?–Go to Step 9Go to Step 31
91. Turn the ignition OFF.
2. Connect the A/C pressure gauges.
3. Start the engine.
4. Turn the A/C switch ON.
5. The cooling fans should run at high speed
when the high side A/C pressure reaches 1
882 kPa (273 psi).
Do the cooling fans run at high speed?–Go to Step 10–
101. Turn the ignition OFF.
2. Connect a scan tool to the DLC.
3. The coolant temperature should be above
97°C (207°C).
4. Disconnect the main cooling fan connector.
5. Turn the ignition ON.
6. Connect a test light between the main cooling
fan connector terminal 2 and ground.
Is the test light on?–Go to Step 11Go to Step 12

ENGINE CONTROLS 1F – 95
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
111. Turn the ignition OFF.
2. Connect a scan tool to the DLC.
3. The coolant temperature should be above
97°C (207°C).
4. Disconnect the main cooling fan connector.
5. Connect a test light between the main cooling
fan connector terminal 1 and ground.
Is the test light on?–Go to Step 28Go to Step 17
121. Turn the ignition OFF.
2. Disconnect the cooling fan relay Low.
3. Connect a test light between the cooling fan
relay Low connector terminal 85 and ground.
4. Turn the ignition ON.
Is the test light on?–Go to Step 13Go to Step 24
131. Turn the ignition OFF.
2. Connect the cooling fan relay Low.
3. Disconnect engine control module (ECM) white
connector.
4. Connect a fused jumper between the ECM
connector terminal 10 and ground.
5. Turn the ignition ON.
Do the cooling fans run at low speed?–Go to Step 30Go to Step 14
14Check for an open wire between the low speed cool-
ing fan relay connector terminal 85 and the ECM
connector terminal 10.
Is the problem found?–Go to Step 25Go to Step 15
151. Turn the ignition OFF.
2. Disconnect the cooling fan relay Low.
3. Connect a test light between the cooling fan
relay Low connector terminal 30 and ground.
Is the test light on?–Go to Step 16Go to Step 23
16Connect a fused jumper between the cooling fan
relay Low connector terminals 30 and 87.
Do the cooling fans run at low speed?–Go to Step 26Go to Step 17
171. Disconnect the cooling fan control relay.
2. Connect a fused jumper between the cooling
fan relay Low connector terminals 30 and 87.
3. Connect a fused jumper between the cooling
fan control relay connector terminals 30 and
87.
Do the cooling fans run at low speed?–Go to Step 27Go to Step 18
18Check the wire between the cooling fan relay Low
connector terminal 87 to the main cooling fan con-
nector terminal 2 for an open.
Is the problem found?–Go to Step 22Go to Step 19
19Check the wire between the main cooling fan con-
nector terminal 1 and the cooling fan control relay
connector terminal 30 for an open.
Is the problem found?–Go to Step 22Go to Step 20

1F – 96IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
20Check the wire between the cooling fan control relay
connector terminal 87A and the auxiliary cooling fan
connector terminal 2 for an open.
Is the problem found?–Go to Step 22Go to Step 21
21Check for an open wire between the auxiliary cooling
fan connector terminal 1 and ground.
Is the problem found?–Go to Step 22Go to Step 29
22Repair the open wire as needed.
Is the repair complete?–System OK–
23Repair the open between the cooling fan relay Low
connector terminal 30 and the fuse Ef11.
Is the repair complete?–System OK–
24Repair the open between the cooling fan relay Low
connector terminal 86 and the ignition switch.
Is the repair complete?–System OK–
25Repair the open wire between the cooling fan relay
Low connector terminal 85 and the ECM connector
terminal 10.
Is the repair complete?–System OK–
26Replace the cooling fan relay Low.
Is the repair complete?–System OK–
27Replace the cooling fan control relay.
Is the repair complete?–System OK–
28Replace the main cooling fan.
Is the repair complete?–System OK–
29Replace the auxiliary cooling fan.
Is the repair complete?–System OK–
30Replace the ECM.
Is the repair complete?–System OK–
311. Turn the ignition OFF.
2. Disconnect the main cooling fan connector.
3. Connect a test light between the main cooling
fan connector termina 2 and ground.
4. Turn the A/C switch ON.
5. Start the engine.
Is the test light on?–Go to Step 32Go to Step 12
321. Turn the ignition OFF.
2. Connect a test light between the main cooling
fan connector terminal 1 and battery positive.
3. Turn the A/C switch ON.
4. Start the engine.
Is the test light on?–Go to Step 28Go to Step 17
331. Turn the ignition OFF.
2. Disconnect the cooling fan relay Hi.
3. Connect a test light between the cooling fan
relay Hi connector terminal 86 and ground.
4. Turn the ignition ON.
Is the test light on?–Go to Step 34Go to Step 44

ENGINE CONTROLS 1F – 97
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
341. Turn the ignition OFF.
2. Connect a test light between the cooling fan
relay Hi connector terminal 30 and ground.
Is the test light on?–Go to Step 35Go to Step 45
351. Disconnect the cooling fan control relay.
2. Connect a test light between the cooling fan
control relay connector terminal 85 and ground.
3. Turn the ignition ON.
Is the test light on?–Go to Step 36Go to Step 46
361. Turn the ignition OFF.
2. Connect a test light between the cooling fan
control relay connector terminal 87 and battery
positive.
Is the test light on?–Go to Step 37Go to Step 47
371. Connect the main cooling fan connector.
2. Connect the cooling fan relay Hi.
3. Connect the cooling fan control relay.
4. Disconnect the ECM connector.
5. Connect a fused jumper between the ECM
connector terminal 10 and ground.
6. Connect a fused jumper between the ECM
connector terminal 9 and ground.
7. Turn the ignition ON.
Do the cooling fans run at high speed?–Go to Step 30Go to Step 38
381. Turn the ignition OFF.
2. Check for an open wire between the cooling
fan relay Hi connector terminal 85 and the
ECM connector terminal 9.
Is the problem found?–Go to Step 22Go to Step 39
391. Disconnect the cooling fan relay Hi.
2. Connect a test light between the cooling fan
relay Hi connector terminal 87 and battery posi-
tive.
Is the test light on?–Go to Step 40Go to Step 48
401. Disconnect the ECM connector.
2. Connect a fused jumper between the ECM
connector terminal 9 and ground.
3. Disconnect the cooling fan relay Hi.
4. Connect a test light between the cooling fan
control relay connector terminal 86 and battery
positive.
Is the test light on?–Go to Step 41Go to Step 49

ENGINE CONTROLS 1F – 101
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
31. Check the engine fuse block fuse Ef21, Ef6,
Ef8.
2. Replace the fuse as needed.
Is the fuse OK?–Go to Step 4Go to
”Diagnostic
Aids”
41. Turn the ignition OFF.
2. Turn the A/C switch OFF.
3. Connect a scan tool to the data link connector
(DLC).
4. The cooling fans should run at low speed when
the coolant temperature reaches 97°C
(207°F).
Do the cooling fans run at low speed?–Go to Step 5Go to Step 10
51. Turn the ignition OFF.
2. Turn the A/C switch OFF.
3. Connect a scan tool to the DLC.
4. Start the engine.
5. The cooling fans should run at high speed
when the coolant temperature reaches 101°C
(214°F).
Do the cooling fans run at high speed?–Go to Step 6Go to Step 33
61. Turn the ignition OFF.
2. Start the engine.
3. Turn the A/C switch ON.
Does the A/C compressor clutch engage?–Go to Step 8Go to Step 7
71. Diagnose the A/C compressor clutch circuit.
2. Repair the A/C compressor clutch circuit as
needed.
3. Start the engine.
4. Turn the A/C switch ON.
Does the A/C compressor clutch engage?–Go to Step 8–
8Do the cooling fans run at low speed?–Go to Step 9Go to Step 31
91. Turn the ignition OFF.
2. Connect the A/C pressure gauges.
3. Start the engine.
4. Turn the A/C switch ON.
5. The cooling fans should run at high speed
when the high side A/C pressure reaches 1
882 kPa (273 psi).
Do the cooling fans run at high speed?–Go to Step 10–
101. Turn the ignition OFF.
2. Connect a scan tool to the DLC.
3. The coolant temperature should be above
97°C (207°C).
4. Disconnect the main cooling fan connector.
5. Turn the ignition ON.
6. Connect a test light between the main cooling
fan connector terminal 2 and ground.
Is the test light on?–Go to Step 11Go to Step 12

1F – 102IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
111. Turn the ignition OFF.
2. Connect a scan tool to the DLC.
3. The coolant temperature should be above
97°C (207°C).
4. Disconnect the main cooling fan connector.
5. Connect a test light between the main cooling
fan connector terminal 1 and ground.
Is the test light on?–Go to Step 28Go to Step 17
121. Turn the ignition OFF.
2. Disconnect the cooling fan relay Low.
3. Connect a test light between the cooling fan
relay Low connector terminal 85 and ground.
4. Turn the ignition ON.
Is the test light on?–Go to Step 13Go to Step 24
131. Turn the ignition OFF.
2. Connect the cooling fan relay Low.
3. Disconnect engine control module (ECM) white
connector.
4. Connect a fused jumper between the ECM
connector terminal K28 and ground.
5. Turn the ignition ON.
Do the cooling fans run at low speed?–Go to Step 30Go to Step 14
14Check for an open wire between the low speed cool-
ing fan relay connector terminal 85 and the ECM
connector terminal K28.
Is the problem found?–Go to Step 25Go to Step 15
151. Turn the ignition OFF.
2. Disconnect the cooling fan relay Low.
3. Connect a test light between the cooling fan
relay Low connector terminal 30 and ground.
Is the test light on?–Go to Step 16Go to Step 23
16Connect a fused jumper between the cooling fan
relay Low connector terminals 30 and 87.
Do the cooling fans run at low speed?–Go to Step 26Go to Step 17
171. Disconnect the cooling fan control relay.
2. Connect a fused jumper between the cooling
fan relay Low connector terminals 30 and 87.
3. Connect a fused jumper between the cooling
fan control relay connector terminals 30 and
87.
Do the cooling fans run at low speed?–Go to Step 27Go to Step 18
18Check the wire between the cooling fan relay Low
connector terminal 87 to the main cooling fan con-
nector terminal 2 for an open.
Is the problem found?–Go to Step 22Go to Step 19
19Check the wire between the main cooling fan con-
nector terminal 1 and the cooling fan control relay
connector terminal 30 for an open.
Is the problem found?–Go to Step 22Go to Step 20

ENGINE CONTROLS 1F – 103
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
20Check the wire between the cooling fan control relay
connector terminal 87A and the auxiliary cooling fan
connector terminal 2 for an open.
Is the problem found?–Go to Step 22Go to Step 21
21Check for an open wire between the auxiliary cooling
fan connector terminal 1 and ground.
Is the problem found?–Go to Step 22Go to Step 29
22Repair the open wire as needed.
Is the repair complete?–System OK–
23Repair the open between the cooling fan relay Low
connector terminal 30 and the fuse Ef21.
Is the repair complete?–System OK–
24Repair the open between the cooling fan relay Low
connector terminal 86 and the ignition switch.
Is the repair complete?–System OK–
25Repair the open wire between the cooling fan relay
Low connector terminal 85 and the ECM connector
terminal K28.
Is the repair complete?–System OK–
26Replace the cooling fan relay Low.
Is the repair complete?–System OK–
27Replace the cooling fan control relay.
Is the repair complete?–System OK–
28Replace the main cooling fan.
Is the repair complete?–System OK–
29Replace the auxiliary cooling fan.
Is the repair complete?–System OK–
30Replace the ECM.
Is the repair complete?–System OK–
311. Turn the ignition OFF.
2. Disconnect the main cooling fan connector.
3. Connect a test light between the main cooling
fan connector termina 2 and ground.
4. Turn the A/C switch ON.
5. Start the engine.
Is the test light on?–Go to Step 32Go to Step 12
321. Turn the ignition OFF.
2. Connect a test light between the main cooling
fan connector terminal 1 and battery positive.
3. Turn the A/C switch ON.
4. Start the engine.
Is the test light on?–Go to Step 28Go to Step 17
331. Turn the ignition OFF.
2. Disconnect the cooling fan relay Hi.
3. Connect a test light between the cooling fan
relay Hi connector terminal 86 and ground.
4. Turn the ignition ON.
Is the test light on?–Go to Step 34Go to Step 44

1F – 104IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
341. Turn the ignition OFF.
2. Connect a test light between the cooling fan
relay Hi connector terminal 30 and ground.
Is the test light on?–Go to Step 35Go to Step 45
351. Disconnect the cooling fan control relay.
2. Connect a test light between the cooling fan
control relay connector terminal 85 and ground.
3. Turn the ignition ON.
Is the test light on?–Go to Step 36Go to Step 46
361. Turn the ignition OFF.
2. Connect a test light between the cooling fan
control relay connector terminal 87 and battery
positive.
Is the test light on?–Go to Step 37Go to Step 47
371. Connect the main cooling fan connector.
2. Connect the cooling fan relay Hi.
3. Connect the cooling fan control relay.
4. Disconnect the ECM connector.
5. Connect a fused jumper between the ECM
connector terminal K28 and ground.
6. Connect a fused jumper between the ECM
connector terminal K12 and ground.
7. Turn the ignition ON.
Do the cooling fans run at high speed?–Go to Step 30Go to Step 38
381. Turn the ignition OFF.
2. Check for an open wire between the cooling
fan relay Hi connector terminal 85 and the
ECM connector terminal K12.
Is the problem found?–Go to Step 22Go to Step 39
391. Disconnect the cooling fan relay Hi.
2. Connect a test light between the cooling fan
relay Hi connector terminal 87 and battery posi-
tive.
Is the test light on?–Go to Step 40Go to Step 48
401. Disconnect the ECM connector.
2. Connect a fused jumper between the ECM
connector terminal K12 and ground.
3. Disconnect the cooling fan relay Hi.
4. Connect a test light between the cooling fan
control relay connector terminal 86 and battery
positive.
Is the test light on?–Go to Step 41Go to Step 49