2004 DAEWOO LACETTI filter

ENGINE CONTROLS 1F – 163
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
3With the engine running, operate the vehicle until the
LOOP STATUS indicates closed.
Is the Long Term Fuel Trim value above the specified
value?–30%Go to Step 4Go to Step 5
41. Turn the ignition switch ON, with the engine
OFF.
2. Review the Freeze Frame data and note the
parameters.
3. Operate the vehicle within the Freeze Frame
conditions and Conditions for Setting The DTC
as noted.
Does the Long Term Fuel Trim value above the spe-
cified value while operating under the specified con-
ditions?–30%Go to Step 21Go to Step 5
5Visually/physically check the air cleaner filter for ex-
cessive dirt or being plugged and repair as needed.
Is the repair complete?–Go to Step 21Go to Step 6
6Visually/physically check the air intake system for
collapsed or restricted and repair as needed.
Is the repair complete?–Go to Step 21Go to Step 7
7Inspect the throttle body inlet for damaged or foreign
objects which may partially block the airflow and re-
pair as needed.
Is the repair complete?–Go to Step 21Go to Step 8
81. Turn the ignition OFF.
2. Inspect the throttle bore, throttle plate and Idle
Air Control (IAC) passages for clocking and
foreign objects and repair as needed.
Is the repair complete?–Go to Step 21Go to Step 9
9Start the engine with the vehicle in park or neutral
and A/C off and note the idle quality.
Is a low or unsteady idle being experienced?–Go to Step 10Go to Step 12
10Idle the engine.
Are the IAC counts below the specified value?100Go to Step 12Go to Step 11
111. Turn the ignition OFF.
2. Disconnect the Manifold Absolute Pressure
(MAP) sensor electrical connector.
3. Start the engine.
4. Operate the vehicle in Closed Loop while moni-
toring the Long Term Fuel Trim value.
Does the Long Term Fuel Trim value increase above
the specified value?–30%Go to Step 20Go to Step 12
12Check the IAC valve performance. Refer to ”DTC
P0506 Idle Speed RPM Lower Than Desired Idle
Speed” or ”DTC P0507 Idle Speed RPM Higher
Than Desired Idle Speed” in this section and repair
as necessary.
Is the repair complete?–Go to Step 21Go to Step 13

ENGINE CONTROLS 1F – 195
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0327
KNOCK SENSOR CIRCUIT FAULT (1.4L DOHC)
Circuit Description
The knock sensor (KS) system is used to detect engine
detonation, allowing the engine control module (ECM) to
retard ignition control spark timing based on the KS signal
being received. The KS produces an AC signal so that un-
der a no knock condition the signal on the KS circuit mea-
sures about 0.007V AC. The KS signal’s amplitude and
frequency depend upon the amount of knock being experi-
enced. The ECM contains a non–replaceable knock filter
module called a signal–to–noise enhancement filter
(SNEF) module. This filter module in the ECM determines
whether knock is occurring by comparing the signal level
on the KS circuit with the voltage level on the noise chan-
nel. The noise channel allows the ECM to reject any false
knock signal by knowing the amount of normal engine me-
chanical noise present. Normal engine noise varies de-
pending on engine speed and load. When the ECM deter-
mines that an abnormally low noise channel voltage level
is being experienced, a DTC P0327 will set.
Conditions for Setting the DTC
S The knock sensor SPI bus in failure during 8 sec-
onds.
Or
S The knock sensor voltage is less than 0.3V.
S The engine coolant temperature is greater than
60°C (145°F).
S The engine speed is greater than 1,500 rpm.
S The mass air flow is higer than 180mg/tdc.
Or
S When difference between a original signal valve
and filtering valve is less than 5%.S The engine coolant temperature is greater than
60°C (145°F).
S The mass air flow is greater than 180mg/tdc.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will not illumi-
nate.
S The ECM will store wnditions which were present
when the DTC was set as Failure Records data
only.
S This information will not be stored in the Freeze
Frame data.
Conditions for Clearing the MIL/DTC
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Check and correct any abnormal engine noise before us-
ing the diagnostic table.
Any circuitry that is suspected as causing engine noise
complaint should be thoroughly checked for the following
conditions :
S Backed–out terminals
S Improper mating
S Broken locks
S Improperly formed
S Damaged terminals
S Poor terminal–to–wire connection
S Physical damage to the wiring harness

1F – 198IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0327
KNOCK SENSOR CIRCUIT FAULT (1.6L DOHC)
Circuit Description
The knock sensor (KS) system is used to detect engine
detonation, allowing the transaxle control module
(TCM)/engine control module (ECM) to retard ignition con-
trol spark timing based on the KS signal being received.
The KS produces an AC signal so that under a no knock
condition the signal on the KS circuit measures about
0.007V AC. The KS signal’s amplitude and frequency de-
pend upon the amount of knock being experienced. The
ECM contains a non–replaceable knock filter module
called a signal–to–noise enhancement filter (SNEF) mod-
ule. This filter module in the ECM determines whether
knock is occurring by comparing the signal level on the KS
circuit with the voltage level on the noise channel. The
noise channel allows the ECM to reject any false knock
signal by knowing the amount of normal engine mechani-
cal noise present. Normal engine noise varies depending
on engine speed and load. When the ECM determines that
an abnormally low noise channel voltage level is being ex-
perienced, a DTC P0327 will set.
Conditions for Setting the DTC
S The knock sensor SPI bus in failure during 10 sec-
onds.
Or
S The knock sensor voltage is less than 0.3V.
S The engine coolant temperature is greater than
60°C(145°F).
S The engine speed is greater than 1,500rpm.
S The mass air flow is higer than 180mg/tdc.
Or
S When difference between a original signal valve
and filtering valve is less than 5%.S The engine coolant temperature is greater than
60°C(145°F).
S The mass air flow is greater than 170mg/tdc.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive trip with a fail.
S The ECM will record operating conditions at the
time the diagnostic fail. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Check and correct any abnormal engine noise before us-
ing the diagnostic table.
Any circuitry that is suspected as causing engine noise
complaint should be thoroughly checked for the following
conditions :
S Backed–out terminals
S Improper mating
S Broken locks
S Improperly formed
S Damaged terminals
S Poor terminal–to–wire connection
S Physical damage to the wiring harness

ENGINE CONTROLS 1F – 309
DAEWOO V–121 BL4
S The ECM will record operating conditions at the
time the diagnostic fail. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Due to moisture associated with exhaust systems, the
EGR valve may freeze and stick in cold weather at times.
After the vehicle is brought into a warm shop for repairs,
the valve warms and the problem disappears.
By watching the Actual EGR and desired EGR positions
on a cold vehicle with a scan tool, the fault can be easily
verified. Check the Freeze Frame data to determine if the
DTC set when the vehicle was cold by viewing the Engine
Coolant Temperature (ECT).
DTC P1402 – Exhaust Gas Recirculation Blocked
StepActionValue(s)YesNo
1Perform an Euro On–Board Diagnostic (EOBD)
System Check.
Is the system check complete?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Start the engine and allow the engine to idle.
2. Install the scan tool.
3. Command the exhaust gas recirculation (EGR)
valve to the specified values.
Does the engine stall or attempt to stall?50%Go to Step 5Go to Step 3
31. Turn the ignition switch to LOCK.
2. Remove the EGR valve assembly.
3. Inspect the EGR valve, passages and pipe for
a restriction or damage and repair as neces-
sary.
Is a repair necessary?–Go to Step 5Go to Step 4
4Replace the EGR valve.
Is the replacement complete?–Go to Step 5–
51. Start the engine.
2. Disconnect the battery for the specified time.
3. Drive the vehicle to the specified value.
4. Release the throttle and allow the vehicle to
decelerate to the specified value.
Is the EGR Decel Filter Values less than the speci-
fied value?10 secnds
60mph
(27km/h)
20mph
(32km/h)
0mphGo to Step 3Go to Step 6
61. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting the DTC as specifiec in the supporting
text.
Does the scan tool indicate that this diagnostic ran
and passed?–Go to Step 7Go to Step 2

ENGINE CONTROLS 1F – 373
DAEWOO V–121 BL4
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S The DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
S Fuel pressure – The system will be lean if the fuel
pressure is too low. It may be necessary to monitor
the fuel pressure while driving the vehicle at various
road speeds and/or loads to confirm. Refer to ”Fuel
System Diagnosis” in this section.
S Manifold Absolute Pressure (MAP) sensor – An
output that causes the ECM to sense a lower than
normal manifold pressure (high vacuum) can cause
the system to go lean. Disconnecting the MAP sen-
sor will allow the ECM to substitute a fixed (default)
value for the MAP sensor. If the lean condition is
gone when the sensor is disconnected, substitute a
known good sensor and recheck.
S Fuel contamination – Water, in even small amounts
near the in–tank fuel pump inlet can be delivered to
the injector. The water causes a lean exhaust and
can set DTC P0131.
S Sensor harness – The HO2S1 sensor pigtail may
be mis–positioned and contacting the exhaust man-
ifold.
S Engine misfire – A misfiring cylinder will result in
unburned oxygen in the exhaust, which could cause
DTC P0131 to set. Refer to DTC P0300 Engine
Misfire in this section.S Cracked Front Heated Oxygen Sensor – A cracked
HO2S1 or poor ground at the sensor could cause
DTC P0131. Refer to”Symptoms Diagnosis” in this
section.
S Plugged fuel filter – A plugged fuel filter can cause
a lean condition and cause a DTC P0131 to set.
S Plugged Front Heated Oxygen Sensor – A plugged
reference port on the HO2S1 will indicate a lower–
than–normal voltage output from the HO2S1.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. This step determines if DTC P0131 is the result of
a hard failure or an intermittent condition. It may be
necessary to operate the vehicle within the Freeze
Frame conditions and Conditions for Setting the
DTC in order to duplicate the malfunction detected
by the ECM.
4. This step simulates DTC P0134. If the ECM senses
the change, the ECM and the wiring are OK.
6. The replacement ECM must be reprogrammed.
Refer to the latest Techline procedure for ECM re-
programming.
8. If no malfunctions have been found at this point and
no additional DTCs were set, refer to ”Diagnostic
Aids” for additional checks and information.
DTC P0131 – Front Heated Oxygen Sensor (HO2S1) Low Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Is the check completed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Start the engine and idle at normal operating
temperature.
Does the Front Heated Oxygen Sensor (HO2S1)
voltage remain below the value specified?0.1 VGo to Step 4Go to Step 3
31. Review the Freeze Frame data and note the
parameters.
2. Operate the vehicle within the Freeze frame
conditions and Conditions For Setting the DTC
as noted.
Does the HO2S1 voltage stay below the specified
value?0.1 VGo to Step 4Go to Step 7

ENGINE CONTROLS 1F – 385
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0135
FRONT HEATED OXYGEN SENSOR (HO2S1) HEATER
CIRCUIT NOT FUNCTIONING
Circuit Description
Heated oxygen sensors (HO2S) are used for fuel control
and post catalyst monitoring. Each HO2S compares the
oxygen content of the surrounding air with the oxygen con-
tent in the exhaust stream. The HO2S must reach operat-
ing temperature to provide an accurate voltage signal. A
heating element inside the HO2S minmizes the time re-
quired for the sensor to reach operating temperature. Volt-
age is provided to the heater by the ignition 1 voltage cir-
cuit through a fuse. With the engine running, ground is
provided to the heater by the HO2S heater low control cir-
cuit, through a low side driver within the engine control
module (ECM). The ECM monitors the current flow
through the heater for diagnosis.
If the ECM detects that the HO2S heater current is above
or blelow a specified range, DTC P0135 seats.
Conditions for Setting the DTC
S DTCs P0106, P0117, P0118, P1017 are not set.
S Engine run time is greater than 200 seconds.
S Filtered O2 heater current is less than 0.025 amps.
Action Taken When the DTC SetsS The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history Diagnostic Trouble Code (DTC) is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after three consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
An intermittent may be caused by rubbed through wire in-
sulation or a wire contacting the exhaust.
Check for poor connection or damaged harness – inspect
harness connectors for the following conditions:
S Improper mating
S Broken locks
S Improperly formed
S Damaged terminals
S Poor terminal–to–wire connection

1F – 404IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0172
FUEL TRIM SYSTEM TOO RICH
System Description
To provide the best possible combination of driveability,
fuel economy, and emission control, a Closed Loop air/fuel
metering system is used. While in Closed Loop, the En-
gine Control Module (ECM) monitors the Front Heated
Oxygen Sensor (HO2S1) signal voltage and adjusts fuel
delivery based on signal voltage. A change made to fuel
delivery will be indicated by the long and short term fuel
trim values which can be monitored with the scan tool.
Ideal fuel trim values are around 128 (0%). If the HO2S1
signal is indicating a lean condition, the ECM will add fuel
resulting in fuel trim values above 128 (0% to 100%). If a
rich condition is detected, the fuel trim values will be below
128 (0% to –100%), indicating that the ECM is reducing
the amount of fuel delivered. If exhaust emissions reach
an excessive level due to a lean or rich condition, a fuel
trim Diagnostic Trouble Code (DTC) is set.
Conditions for Setting the DTC
S The average of adaptive index multiplier value is
less than 0.75.
S No intrusive tests active.
S DTCs P0106, P0107, P0108, P0112, P0113,
P0117, P0118, P0122, P0123, P0131, P0132,
P0133, P0134, P0135, P1167, P1171, P0336,
P0337, P0341, P0342, P0402, P0404, P1404,
P0405, P0406, P0443, P0506, and P0507 are not
set.
S Throttle Position (TP) is less than 95%.
S Engine speed is between 700 and 6000 rpm.
S Barometric Pressure (BARO) is greater than 72.0
kPa (10.4 psi).
S Coolant temperature is between 70°C (158°F) and
11 5°C (239°F).
S Manifold Absolute Pressure (MAP) is between 25
kPa (3.6 psi) and 99.7 kPa (14.5 psi).
S Intake Air Temperature (IAT) is between –40°C
(–40°F) and 120°C (248°F).
S Airflow is between 1.5 and 45 g/sec.
S Vehicle speed is less than 140 km/h (87 mph).
S System is in closed loop.
S Adaptive index is ready.
S System voltage is greater than 11 volts.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after two consecutive ignitions cycle in which the
diagnostic runs with the fault active (SOHC).
S The Malfunction Indicator Lamp (MIL) will illuminate
after first consecutive ignitions cycle (DOHC).
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.Conditions for Clearing the MIL/DTC
S The MIL will turn off after two consecutive ignition
cycles in which the diagnostic runs without a fault
within the freeze frame conditions that the DTC
failed.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S The DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Important : After repairs, use the scan tool Fuel Trim Re-
set function to reset the long–term fuel trim to 128 (0%).
Check for poor connection at the ECM. Inspect the har-
ness connectors for the following conditions:
S Backed–out terminals.
S Improper mating.
S Broken locks.
S Improperly formed.
S Damaged terminals.
S Poor terminal–to–wire connection.
Inspect the wiring harness for damage. If the harness ap-
pears to be OK, observe the HO2S1 display on the scan
tool while moving the connectors and the wiring harness
related to the engine harness. A change in the display will
indicate the location of the fault.
If a DTC P1404 is also set, check the 5 volt reference cir-
cuits for a short to voltage.
Check for a restricted exhaust system.
A shorted 5 volt reference circuit may cause a DTC P0172
to set. Check the 5 volt reference sensors for abnormal
readings.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
5. A clogged air cleaner filter element restricts the air-
flow coming into the engine. This step checks the
condition of the air cleaner filter.
17. A leaky injector can cause a rich condition and set
DTC P0172. Refer to ”Fuel Injector Balance Test”
in this section.
19. A loose TP sensor may not set a TP sensor related
DTC, but may cause the system to become rich by
a higher–than–actual TP reading.

ENGINE CONTROLS 1F – 405
DAEWOO V–121 BL4
DTC P0172 – Fuel Trim System Too Rich
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install the scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON.
Are any component related Diagnostic Trouble
Codes (DTCs) set?–Go to applica-
ble DTC tableGo to Step 3
3With the engine running, operate the vehicle until the
LOOP STATUS indicates closed.
Is the Long Term Fuel Trim value above the specified
value?–20%Go to Step 4Go to Step 5
41. Turn the ignition switch ON, with the engine
OFF.
2. Review the Freeze Frame data and note the
parameters.
3. Operate the vehicle within the Freeze Frame
conditions and Conditions for Setting The DTC
as noted.
Does the Long Term Fuel Trim value above the spe-
cified value while operating under the specified con-
ditions?–20%Go to Step 21Go to Step 5
5Visually/physically check the air cleaner filter for ex-
cessive dirt or being plugged and repair as needed.
Is the repair complete?–Go to Step 21Go to Step 6
6Visually/physically check the air intake system for
collapsed or restricted and repair as needed.
Is the repair complete?–Go to Step 21Go to Step 7
7Inspect the throttle body inlet for damaged or foreign
objects which may partially block the airflow and re-
pair as needed.
Is the repair complete?–Go to Step 21Go to Step 8
81. Turn the ignition OFF.
2. Inspect the throttle bore, throttle plate and Idle
Air Control (IAC) passages for clocking and
foreign objects and repair as needed.
Is the repair complete?–Go to Step 21Go to Step 9
9Start the engine with the vehicle in park or neutral
and A/C off and note the idle quality.
Is a low or unsteady idle being experienced?–Go to Step 10Go to Step 12
10Idle the engine.
Are the IAC counts below the specified value?100Go to Step 12Go to Step 11