2004 DAEWOO LACETTI Lamp

1F – 378IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0133
FRONT HEATED OXYGEN SENSOR (HO2S1) SLOW
RESPONSE
Circuit Description
The Engine Control Module (ECM) continuously monitors
the Front Heated Oxygen Sensor (HO2S1) activity for 100
seconds. During the monitor period, the ECM counts the
number of times that the HO2S1 switches from rich to lean
and from lean to rich and adds the amount of time it took
to complete all switches. With this information, an average
time for all switches can be determined. If the average time
to switch is too out of specification, a DTC P0133 will set.
If the HO2S1 pigtail wiring, connector, or terminal is dam-
aged, the entire HO2S1 assembly must be replaced. Do
not attempt to repair the wiring, connector, or terminals. In
order for the sensor to function properly, it must have a
clean air reference provided to it. This clean air reference
is obtained by way of the HO2S1 wire(s). Any attempt to
repair the wires, connector, or terminals could result in the
obstruction of the air reference and degrade HO2S1 per-
formance.
Conditions for Setting the DTCS HO2S1 average transition time between 0.3–0.6
volts, lean to rich is greater than 156 millisec-
onds(A/T) or rich to lean is greater than 140 milli-
seconds (M/T).
S Closed loop stoichiometry.
S Engine Coolant Temperature (ECT) is greater than
70°C (158°F).
S System voltage is greater than 10 volts.
S Engine run time is greater than 60 seconds.
S Purge Duty Cycle (DC) is less than 20%.
S The rpm is between 1600 and 4300.
S Airflow is between 9 and 40 g/sec.
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0131, P0132, P0134, P0135,
P1167, P0171, P1171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0402, P0404, P0405, P0406, P0506,
P0507, P1404, and P0443 are not set.
S 2 second delay after conditions are met.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.

1F – 382IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0134
FRONT HEATED OXYGEN SENSOR (HO2S1) NO
ACTIVITY OR OPEN
Circuit Description
The Engine Control Module (ECM) supplies a voltage of
about 0.45 volts between terminals M12 and M29 (if mea-
sured with a 10 megohm digital voltmeter, this may read
as low as 0.32 volts). The Front Heated Oxygen Sensor
(HO2S1) varies the voltage within a range of about 1 volt
if the exhaust is rich, down through about 0.10 volts if the
exhaust is lean.
The sensor is like and open circuit and produces no volt-
age when it is below 315 °C (600 °F). An open sensor cir-
cuit or cold sensor causes Open Loop operation.
If the HO2S1 pigtail wiring, connector, or terminal is dam-
aged, the entire HO2S1 assembly must be replaced. Do
not attempt to repair the wiring, connector, or terminals. In
order for the sensor to function properly, it must have a
clean air reference provided to it. This clean air reference
is obtained by way of the HO2S1 wire(s). Any attempt to
repair the wires, connector or terminals could result in the
obstruction of the air reference and degrade the HO2S1
performance. Refer to”Front Heated Oxygen Sensor
(HO2S1)” in this section.Conditions for Setting the DTC
S HO2S1 voltage is between 420 and 480 mV.
S Engine Coolant Temperature (ECT) is greater than
60 °C (140 °F)
S System voltage is greater than 10 volts.
S Engine run time is greater than 60 seconds.
S Airflow is greater than 8 g/sec.
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0402, P0404, P0405, P0406, P0506,
P0507, P1404, and P0443 are not set.
S 3 second delay after exiting Decel Fuel Cut–off
(DFCO) mode.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illumi-
nate.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
S The vehicle will operate in Open Loop.

ENGINE CONTROLS 1F – 385
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0135
FRONT HEATED OXYGEN SENSOR (HO2S1) HEATER
CIRCUIT NOT FUNCTIONING
Circuit Description
Heated oxygen sensors (HO2S) are used for fuel control
and post catalyst monitoring. Each HO2S compares the
oxygen content of the surrounding air with the oxygen con-
tent in the exhaust stream. The HO2S must reach operat-
ing temperature to provide an accurate voltage signal. A
heating element inside the HO2S minmizes the time re-
quired for the sensor to reach operating temperature. Volt-
age is provided to the heater by the ignition 1 voltage cir-
cuit through a fuse. With the engine running, ground is
provided to the heater by the HO2S heater low control cir-
cuit, through a low side driver within the engine control
module (ECM). The ECM monitors the current flow
through the heater for diagnosis.
If the ECM detects that the HO2S heater current is above
or blelow a specified range, DTC P0135 seats.
Conditions for Setting the DTC
S DTCs P0106, P0117, P0118, P1017 are not set.
S Engine run time is greater than 200 seconds.
S Filtered O2 heater current is less than 0.025 amps.
Action Taken When the DTC SetsS The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history Diagnostic Trouble Code (DTC) is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after three consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
An intermittent may be caused by rubbed through wire in-
sulation or a wire contacting the exhaust.
Check for poor connection or damaged harness – inspect
harness connectors for the following conditions:
S Improper mating
S Broken locks
S Improperly formed
S Damaged terminals
S Poor terminal–to–wire connection

1F – 388IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0137
REAR HEATED OXYGEN SENSOR (HO2S2) LOW
VOLTAGE
Circuit Description
In order to control emissions, a catalytic converter is used
to convert harmful emissions into harmless water vapor
and carbon dioxide.
The Engine Control Module (ECM) has the ability to moni-
tor this process by using a Rear Heated Oxygen Sensor
(HO2S2). The HO2S2, located in the exhaust stream past
the catalytic converter, produces an output signal which in-
dicates the storage capacity of the catalyst. This in turn in-
dicates the catalyst’s ability to convert exhaust emissions
effectively. If the catalyst is functioning properly, the
HO2S2 signal will be far less active than the signal pro-
duced by the Front Heated Oxygen Sensor (HO2S1).
If the HO2S2 pigtail wiring, connector, or terminal is dam-
aged, the entire HO2S2 assembly must be replaced. Do
not attempt to repair the wiring, connector, or terminals. In
order for the sensor to function properly, it must have a
clean air reference provided to it. This clean air reference
is obtained by way of the HO2S2 wire(s). Any attempt to
repair the wires, connector, or terminals could result in the
obstruction of the air reference and degrade the HO2S2
performance.Conditions for Setting the DTC
S HO2S2 voltage is less than 0.05 volt in Closed
Loop control or less than 0.35 volt in Power Enrich-
ment (PE) mode.
S Engine Coolant Temperature (ECT) is greater than
60°C (140°F).
S System voltage is greater than 10 volts.
S Closed Loop test: 3 seconds delay after in Closed
Loop and air flow is greater than 9 g/sec.
S Power Enrichment test: Air/Fuel ration is less than
or equal to 13.5 and 3 seconds delay after in Power
Enrichment mode.
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0141, P0402, P0404, P0405, P0406,
P0506, P0507, P1404, and P0443 are not set.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.

ENGINE CONTROLS 1F – 391
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0138
REAR HEATED OXYGEN SENSOR (HO2S2) HIGH
VOLTAGE
Circuit Description
In order to control emissions, a catalytic converter is used
to convert harmful emissions into harmless water vapor
and carbon dioxide.
The Engine Control Module (ECM) has the ability to moni-
tor this process by using a Rear Heated Oxygen Sensor
(HO2S2). The HO2S2, located in the exhaust stream past
the catalytic converter, produces an output signal which in-
dicates the storage capacity of the catalyst. This in turn in-
dicates the catalyst¡¯s ability to convert exhaust emissions
effectively. If the catalyst is functioning properly, the
HO2S2 signal will be far less active than the signal pro-
duced by the Front Heated Oxygen Sensor (HO2S1).
If the HO2S2 pigtail wiring, connector, or terminal is dam-
aged, the entire HO2S2 assembly must be replaced. Do
not attempt to repair the wiring, connector, or terminals. In
order for the sensor to function properly, it must have a
clean air reference provided to it. This clean air reference
is obtained by way of the HO2S2 wire(s). Any attempt to
repair the wires, connector, or terminals could result in the
obstruction of the air reference and degrade the HO2S2
performance.Conditions for Setting the DTC
S HO2S2 voltage is greater than 0.952 volt in Closed
Loop control or greater than 0.55 volt in Decel Fuel
Cutoff (DFCO) mode.
S Engine Coolant Temperature (ECT) is greater than
60°C (140°F).
S System voltage is greater than 10 volts.
S Closed Loop test: 3 seconds delay after in Closed
Loop and airflow is greater than 9 g/sec.
S DFCO test: 2 seconds delay after in DFCO.
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0141, P0402, P0404, P0405, P0406,
P0506, P0507, P1404, and P0443 are not set.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.

1F – 394IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0140
REAR HEATED OXYGEN SENSOR (HO2S2) NO ACTIVITY
OR OPEN
Circuit Description
In order to control emissions, a catalytic converter is used
to convert harmful emissions into harmless water vapor
and carbon dioxide.
The Engine Control Module (ECM) has the ability to moni-
tor this process by using a Rear Heated Oxygen Sensor
(HO2S2). The HO2S2, located in the exhaust stream past
the catalytic converter, produces an output signal which in-
dicates the storage capacity of the catalyst. This in turn in-
dicates the catalyst is ability to convert exhaust emissions
effectively. If the catalyst is functioning properly, the
HO2S2 signal will be far less active than the signal pro-
duced by the Front Heated Oxygen Sensor (HO2S1).
If the HO2S2 pigtail wiring, connector, or terminal is dam-
aged, the entire HO2S2 assembly must be replaced. Do
not attempt to repair the wiring, connector, or terminals. In
order for the sensor to function properly, it must have a
clean air reference provided to it. This clean air reference
is obtained by way of the HO2S2 wire(s). Any attempt to
repair the wires, connector, or terminals could result in the
obstruction of the air reference and degrade the HO2S2
performance.Conditions for Setting the DTC
S HO2S2 voltage is between 0.422 and 0.478 volts.
S Engine Coolant Temperature (ECT) is greater than
60°C (140°F).
S Engine rum time is greater than 60 seconds.
S System voltage is greater than 10 volts.
S Closed Loop stoichiometry.
S 3 second delay after exiting Decel Fuel Cutoff
(DFCO) mode.
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0141, P0402, P0404, P0405, P0406,
P0506, P0507, P1404, and P0443 are not set.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC

ENGINE CONTROLS 1F – 397
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0141
REAR HEATED OXYGEN SENSOR (HO2S2) HEATER
CIRCUIT NOT FUNCTIONING
Circuit Description
In order to control emissions, a catalytic converter is used
to convert harmful emissions into harmless water vapor
and carbon dioxide.
The Engine Control Module (ECM) has the ability to moni-
tor this process by using a Rear Heated Oxygen Sensor
(HO2S2). The HO2S2, located in the exhaust stream past
the catalytic converter, produces an output signal which in-
dicates the storage capacity of the catalyst. This in turn in-
dicates the catalyst is ability to convert exhaust emissions
effectively. If the catalyst is functioning properly, the
HO2S2 signal will be far less active than the signal pro-
duced by the Front Heated Oxygen Sensor (HO2S1).
If the HO2S2 pigtail wiring, connector, or terminal is dam-
aged, the entire HO2S2 assembly must be replaced. Do
not attempt to repair the wiring, connector, or terminals. In
order for the sensor to function properly, it must have a
clean air reference provided to it. This clean air reference
is obtained by way of the HO2S2 wire(s). Any attempt to
repair the wires, connector, or terminals could result in the
obstruction of the air reference and degrade the HO2S2
performance.The ECM will check if HO2S2 is functioning properly by
monitoring the current to HO2S2 heater. If the current is
less than 0.1 ampere, DTC P0141 will set.
Conditions for Setting the DTC
S HO2S2 heater current is less than 0.1 amperes.
S Engine rum time is greater than 60 seconds.
S System voltage is greater than 10 volts.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S The DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.

1F – 400IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0171
FUEL TRIM SYSTEM TOO LEAN
System Description
To provide the best possible combination of driveability,
fuel economy, and emission control, a Closed Loop air/fuel
metering system is used. While in Closed Loop, the En-
gine Control Module (ECM) monitors the Front Heated
Oxygen Sensor (HO2S1) signal voltage and adjusts fuel
delivery based on signal voltage. A change made to fuel
delivery will be indicated by the long and short term fuel
trim values which can be monitored with the scan tool.
Ideal fuel trim values are around 128 (0%). If the HO2S1
signal is indicating a lean condition, the ECM will add fuel
resulting in fuel trim values above 128 (0% to 100%). If a
rich condition is detected, the fuel trim values will be below
128 (0% to –100%), indicating that the ECM is reducing
the amount of fuel delivered. If exhaust emissions reach
an excessive level due to a lean or rich condition, a fuel
trim Diagnostic Trouble Code (DTC) is set.
Conditions for Setting the DTC
S The average of adaptive index multiplier value is
greater than 1.28.
S No intrusive tests active.
S DTCs P0106, P0107, P0108, P0112, P0113,
P0117, P0118, P0122, P0123, P0131, P0132,
P0133, P0134, P0135, P1167, P1171, P0300,
P0336, P0337, P0341, P0342, P0402, P0404,
P1404, P0405, P0406, P0443, P0506, and P0507
are not set.
S Throttle Position (TP) is less than 95%.
S Engine speed is between 700 and 6000 rpm.
S Barometric Pressure (BARO) is greater than 72.0
kPa (10.4 psi).
S Coolant temperature is between 70°C (158°F) and
11 5°C (239°F).
S Manifold Absolute Pressure (MAP) is between 25
kPa (3.6 psi) and 99.7 kPa (14.5 psi).
S Intake Air Temperature (IAT) is between –40°C
(–40°F) and 120°C (248°F).
S Airflow is between 1.5 and 45 g/sec.
S Vehicle speed is less than 140 km/h (87 mph).
S System is in closed loop.
S Adaptive index is ready.
S System voltage is greater than 11 volts.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after two consecutive ignitions cycle in which the
diagnostic runs with the fault active.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.Conditions for Clearing the MIL/DTC
S The MIL will turn off after two consecutive ignition
cycles in which the diagnostic runs without a fault
within the freeze frame conditions that the DTC
failed.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S The DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
Important : After repairs, use the scan tool Fuel Trim Re-
set function to reset the long–term fuel trim to 128 (0%).
S Fuel pressure – The system will be lean if the pres-
sure is too low. It may be necessary to monitor fuel
pressure while driving the vehicle at various road
speeds and/or loads to confirm.
S Map sensor – An output that causes the ECM to
sense a lower than normal manifold pressure (high
vacuum) can cause the system to go lean. Discon-
necting the MAP sensor will allow the ECM to sub-
stitute a fixed (default) value for the MAP sensor. If
the lean condition is gone when the sensor is dis-
connected, substitute a known good sensor and
recheck.
S Fuel contamination – Water, in even small amounts,
near the in–tank fuel pump inlet can be delivered to
the injector. The water causes a lean exhaust and
can set DTC P0171.
Check for poor HO2S1 or MAP sensor connection at the
ECM. Inspect the harness connectors for the following
conditions:
S Backed–out terminals
S Improper mating
S Broken locks
S Improperly formed
S Damaged terminals
S Poor terminal–to–wire connection
Inspect the wiring harness for damage. If the harness ap-
pears to be OK, observe the HO2S1 display on the scan
tool while moving the connectors and the wiring harness
related to the engine harness. A change in the display will
indicate the location of the fault.
Check the brake power booster check valve for possible
leaks.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-