2004 DACIA SUPERNOVA horn

82B
HORN - ENGINE IMMOBILISER
82B - 47 TABLE 1
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 48TABLE 1
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 49TABLE 2
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 50TABLE 2
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 51
If after a complete checking of the anti intrusion system,
the replacement of the E.C.U. anti
intrusion is required, proceed as follows:
- remove from the central console the tape recorder’s frame and the tape recorder pulling
backward but without disconnecting the tape recorder from the vehicle’s wiring;
- dismount by detaching the aeration grill located on the right side of the central console ;
- dismount the t wo screws attaching t he E CU support i n t he ri ght side of the climate
control unit;
- take off the anti intrusion ECU together with its support through the central zone of the
central console; - disconnect the 24 ways connector from the anti intrusion ECU proceeding as follows:
remove towards exterior the two blocking clips of the connector and then carefully pull out the
connector; - dismount carefully the two way connector from the anti intrusion ECU;
- dismount the two screw attaching the anti intrusion ECU on its support;
- proceed the in reverse order of the dismounting;
- check the proper operation of the anti intrusion system. DISMOUNTING – REMOUNTING
OF THE ANTI INTRUSION ECU
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 52
If siren dismounting is required, proceed as follows:
- dismount the two attachment nuts of the siren on its support;
- pull carefully the blocking clip of the wire connector to the siren and then disconnect the
siren;
- connect to the siren the connector of the wiri ng, by pushing, until you hear a “click”
confirming the correct c onnecting, then mount the two attachment screws of the siren on the
support;
- check the proper operation of the anti intrusion system. SIR
EN DISMOUNTING –REMOUNTING
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 53
The engine hood connector is dismounted as follows:
- easy pull the blocking clip of the wirin g connector and then disconnect the engine hood contact;
- press the blocking clips of the lateral sides of the contact;
- push upward the contact i n order to remove it from its place.
Mount the new contact in its support by downward pushing, until a “click” is heard, confirming
the correct connecting. Connect the wires connector to t he contact of the hood.
Check the proper operation of the hood contact and of the anti intrusion system. DISMOUNTING – REMOUNTING OF THE HOOD CONTACT
vnx.su

82B
HORN - ENGINE IMMOBILISER
82B - 54
NOTE
If the dismounting / remounting of t he front doors or hatchback contacts,
check aft er that , the correct operation of the anti intrusion system.
LEFT SIDE VOLUME SENSOR REPLACEMENT
If sensor replacement is required, proceed as follows:
- take out carefully the sensor from its support by detaching from clips;
- dismount the attachment screw of the sensor support on the front left pillar upholstery.
- dismount the three attachment screws of the upper upholstery of the front left pillar and
carefully remove the upholstery;
- carefully disconnect the sensor connector from the vehicle’s wiring;
- mount the new volume sensor and its support performing the above mentioned operations
in reverse order, and then checking the proper operation of the anti intrusion system.
AT TENT ION
Be sure that the v olume sensor mounted on the l eft side has marked the
letter “T ” on the red colour collar.
Mo unt the volume sensor in such way, to be oriented towards the back of the vehicle,
parallel wi th the side windows.
RIGHT SIDE VOLUME SENSOR REPLACEMENT
If sensor replacement is required, proceed as follows:
- take out carefully the sensor from its support by detaching from clips;
- dismount the attachment screw of the sensor support on the front right pillar upholstery.
- dismount the three attachment screws of the upper upholstery of the front right pillar and
carefully remove the upholstery; - carefully disconnect the sensor connector from the vehicle’s wiring;
- mount the new volume sensor and its support performing the above mentioned operations
in reverse order, and then checking the proper operation of the anti intrusion system.
AT TENT ION
Be sure that the volume sensor mounted on the right side has marked t he l etter
“R” on the white colour collar. Mo unt the volume sensor in such way, to be oriented t owards the bac k of the v ehicle,
parallel wi th the side windows.
V OLUME SENSOR DISMOUNTING – REMOUNTING
vnx.su