2004 DACIA SUPERNOVA horn

82A
HORN - ENGINE IMMOBILISER
82A - 31
No
Is the anti startin
g bus hings correctly fixed on the
steering column and is it correctly connected?Position the bushing and fix its
connection.
Check the continuity and the isolation
related to the ground and the +12 V wiring.Pin2 ground
Pin3 supply +IC
Pin4 pin A2 of the E.C.U. decoder.
Is the wiring in good condition?
Fix the electric wiring.
Disconnect the E.C.U. decoder and check the
presence of +12 V at pin A2 of the wiring.
Is there any tension?
Replace the anti starting bushing.
Connect t he E.C.U. decoder. Perform the
impulse detection t est with t he t ester CLIP
branched to the pin A2 of the E.C.U. decoder.
S et the contact on and check t he presence of
an impulse. Is there any impulse?
Replace the anti starting bushing.
Replace the key.
No
No
No
No
Yes
Yes
Yes
No DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 32
ALP3. THE ANTI STARTING INDICATOR REMAINS PERMANENTLY LIGHTED
(even when the contact is taken off) OR IT REMAINS PERMANENTLY SWITCHE D OFF.
RECOMMENDATIONCheck if the “Procedure E.C.U. decoder replacement” was correctly
performed.
Check the fuse F15 ( up to 01.06.2001) or
F07 (after 01.06.2001).
Is the fuse good?
Is there the failure “ DOORS’ LOCKING
CONTACT”?
Check the continuity and the isolation related
to the ground, between t he pin A 5 of the
E.C.U. decoder and the dashboard.
Is the wiring good?
Replace the fuse.
Analyse this failure and replace.
Fix the wiring.
Perform the following tests in order to find the
failure element:
- if the anti starting indicator is permanently
lighted, disconnect the connector of the E.C.U.
decoder and check if the indicator switches off;
- if the anti starting system is turned off,
c onnect the pin A5 of the wiring connector from
the E.C.U. decoder to an electric ground and
check if the indicator turns on.
Are the answers affirmatives?
Replace the instrument panel.
Replace the E .C.U. decoder.
Perform a conformity checking.
AFTER REPAIRING Check the operation of the anti starting system. Remove by means of the CLIP tester the possibl e memorised failures.
No
No
No
Yes
Yes
No
Yes
YesDIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 33
AL P4 . CONTA CT ON. T HE AN T I START I NG I NDI CAT OR B L INKS
QUICKLY (the engine doesn’t start)
RECOMMENDATION -
Set the contact on.
Connect the CLIP tester.
Is
there any communication between the tester
and E. C.U. decoder ?
Is the state 19D is ACTIVE?
Check the continuity and the isolation related
to the ground and to t he + 12V of the wiring
be t we en A6 de c ode r pi n a nd i nj e c t ion
computer pin 58.
Is the wiring good?
S ee ALP 1.
Check the correct m emorisation of
the anti starting code by the E.C.U.
decoder ; if not, replace the decoder.
Fix the electric wiring.
Perform the impulse detection test by means
of the CLIP tester connected to the E.C.U.
decoder A6 pin.
Set th e conta c t on a nd c he ck i mpulse s
presence.
Are there any impulses?
Replace the injection computer.
Replace E.C.U. decoder or see t he “ Kit
replacement procedure “.
Perform a conformity checking.
AFTER REPAIRING Check the operation of the anti starting system. Remove by means of the CLIP tester the possible memorised failures.
No
Yes
No
Yes
Yes
No
Yes
NoDIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 34
A
LP5. THE VEHICLE DOES NOT START
RECOMMENDATION -
Is there the failure “SIGNAL MISSING ON
THE CODED LINE E.C.U. DECODER –
COMPUTER INJECTION?”
There is a problem at the shock sensor.
There is an engine problem.No
Yes
Perform a conformity checking.
AFTER REPAIRING Check the operation of the anti starting system.
Remove by means of the CLIP tester the possible memorised failures.
DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 35
A
LP6. BLOCKING/UNLOCKING DOORS NOT OPERATING
RECOMMENDATION Check with the CLIP tester the absence of the failures.
If there are memorised failures, these must be removed.
Are the doors blocking mechanisms correctly
operating ?Repair the damaged mechanisms.No
Check the continuity a nd the isolation related to the ground
of the wiring between :
E.C.U . d ecoder pin B8 actuators
Pin B9 doors
Is the wiring in good condition?
Fix the wiring.No
Check the continuity a nd the isolation related
to the ground of the wiring between
E.C.U .pin B8 switch
d ecoder pin B9 blocking doors
Is the wiring in good condition?
Repair.
Di sconnect the E.C.U. decoder, then supply
the wiring connector with +12 V at pin B9 and
the ground at the pin B8, than versa (+ 12 V at
pin B8 and the ground at pin B9).
Ar e the actuators bl ocking/unlocking the
doors?
Damaged actuators.
Replace them.
Replace the E.C.U. decoder, then perform the “E.C.U. decoder replacement
procedure”. No
Yes
Yes
No
YesYes
AFTER REPAIRING Perform a conformity
checking.
Check the operation of the anti starting system.
DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 36
A
LP7. UNLOCKING DOORS NOT OPERATING BY RF REMOTE CONTROL
RECOMMENDATION Check the absence of failures with the CLIP tester.
If there are memorised failures, these must be repaired.
Are the states 11G and 11D ACTIVE when
the RF remote control is activated?S ee the treatment states 11G and
1 1D cf. Chapter “Diagnostic”.No
Check the fuse F15 ( up to 01.06.2001) or
F 07 (after 01.06.2001).
Is it good?
Replace the fuse.No
Yes
Yes
Activate the doors’ locking switch from t he
dashboard.
Are the doors blocking/ unlocking ? S
ee the treatment of the failure
“Doors blocking contact” and the
state 14 G cf. Chapter “Diagnostic”.
S ee ALP 6.
Yes
No
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 37
A
LP8. TURNING LIGHTS DO NOT SWITCH ON AT THE BLOCKING /
UNLOCKING OF THE DOORS
RECOMMENDATION Check the absence of the failures with the CLIP tester.
If there are failures, fix them first.
Check if the synchronisatio n of the RF remote control and the E.C.U. decoder has been performed .
Are the turning lights functioning normally at the activation of the signalling switch ?
Check the continuity and the isolation related to
the ground and the +12 V of the electric layout:
E.C.U. decoder FLASH relay
Pin B3 pole 2
Is it correct?
Repair the signalli ng system.
Check t he fuse F03 and F04.
Fix the electric layout.
Check the fuse F15 ( up to 01.06.2001) or
F 07 (after 01.06.2001).
Is it good?Replace the fuse.
Disconnect the FLASH relay. Supply with
+ 12, the pole 4 of the relay. Are the l eft
turning lights turning on? Supply with +12 V
the pole 5 of the signal relay.
Are the right turning lights turning on?
Repair the electric layout from
poles 4 and 5 of the FLASH relay.
Replace the FLASH relay.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
No
No
No
Yes
Yes
Yes
Yes No
DIAGNOSTIC
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 38
No
AFTER REPAIRING Perform a conformity
checking.
Check the operation of the anti starting system.
A LP9. THE CEILING LAMP DOES NOT SWITCH ON AT THE BLO CKING /
UNLOCKING OF THE DOORS OR IT REMAINS PERMANENTLY TURNED ON.
RECOMMENDATION Check the absence of failures with the CLIP tester.
If there are memorised failures, fix them first.
Check if t he doors are locked?
Has the ceiling lamp turned on? The ceiling lamp was in the
position “p
ermanently
lighting”. Normal
operation.Yes Yes
Unlock the doors with the RF remote control.
The ceiling is in the position “dome lighting”
Has the ceiling lamp turned on?
Check the isolation of the wiring
related to the ground on the line pinA1.
decoder ceiling
After 15 seconds, the ceiling lamp will
turn off.
Normal operation.
Was the E.C.U. decoder confi gured “With
dome ceiling ”?Configure the E.C.U. decoder with
the CLIP tester.
Check the continuity on the line
E. C.U. decoder pin A1 ceiling
Is the line good?Repair .
Check the ceiling lamp bulb.
No
No
No
Yes
Yes Yes
No
DIAGNOSTIC
vnx.su