82B
HORN - ENGINE IMMOBILISER
82B - 43
THE PIN CODE
The PIN code is formed of four figures and it can be used only for deactivating the anti intrusion
s ystem, if this operation can not be performed by pushing the deactivating button from the RF
remote control of the vehicle. For introducing the PIN code, perform as follows:-set on the contact key in the M position and take it off it for three times in seven seconds,
after which the anti intrusion LED indicator will switch on for three seconds; -set on the contact again on the M position and maintain it until the number of the L ED
blinks is e qual with the first figure of the PIN code, then take off the contact; -set on the contact in the M position and maintain it until the number of LED blinks is equal
w ith the second figure of the PIN code, then take off the contact;
-perform the above mentioned method in order to introduce the third and the fourth figure
of the PIN code;
-after that, the system is deactivated and the siren stops automatically;
- set on the contact again – the anti LED indicator must switch on, confirming in this way
that the c orrect introduction of the PIN code.
AT TENT ION
If it i s necessary the checking of the PIN code, t his will be pe rformed
only after al least 20 seconds have passed, since the anti intrusion ECU has been
connected to the vehicle’s wiring or since the connecting of t he vehicle’s battery.
The COBRA anti intrusion system can operate in t hree different modes (2,3 or 4).
For the Super Nova vehicles, the system has been programmed to work in the second operation
mode. If by mistake the PIN code was introduced in less than 20 seconds since the battery
connecting or since connecting the anti intrusion ECU, this can involve the change of the operation
way of the system, which will generate errors during the operation. There is, although, the possibility
of reprogramming the correct operation way (type 2) and in this purpose, perform the following
operations : - disconnect and then reconnect the anti intrusion ECU; when connecting the anti intrusion
ECU the anti intrusion LED indicator will switch on once, confirming the correct connecting;
-af ter at least 5 seconds from the previous operation, but no more than 20 second from it,
perform the following operation s:
-s et on the contact key in the M position for three times and then release it;
- the anti intrusion LED indicator will switch on for three seconds and then will switch off;
- set on again the contact key in the “M” position and maintain it, counting two blinks of the
anti intrusion LED indicator, then take off the contact;
- the LED indicator will blink for two times in two series, confirming in this way the proper
performance of the previous operations;
press the doors locking button of the dashboard, in order to lock and unlock the doors; the anti
intrusion LED indicator must not blink;
vnx.su
84
CONTROLS - SIGNALLING
84 -1
(STARTING – IGNITION SWITCH)
The anti theft mechanism is placed on the right part of the steering column and has the purpose
to starter control when electric system is connected, being provided in the same time also with a
steering locking device, with anti theft lock.
NOTE
At the anti theft mechanism there is not any more marked G position (garage) because
it does not allow the taking out of the key in this position but helps in pi n unblocking
for removing the mechanism from the steering column.
Disconnect the battery.
Dismount the steering wheel casings.
Disconnect the anti-starting bushing.
Remove the bushing off the steering column.
Disconnect the switch connection wires.
B ring the key in the interme diary position (ex G).
Dismount the attachment screw (1).
P ush the mobile pin ( 2) and pull backwards
the switch.
REMOUNTING
Mount the switch in its place.
Tighten the attachment screw(1).
Connect :
- the switch
- the battery.
Position and mount the anti-star ting bushing.
Connect the anti-starting bushing to the ve-
h icle wirin g.
Check the switch operation.
Mount the steering wheel casings. DISMOUNTING
ANTI THEFT MECHANISM
vnx.su
86
RADIO
GENERAL
C ode protection
T he radio is protected by means of a four digit code. This code is introduced by the
radio keys at each battery disconnection.
Co de introduction by means of the radio keys : in order to valid one digit introduction,
push the next key ( see the operation technical book).
In case of a wrong code, the instrument is getting blocked ( one minute for the first error, two
minutes for the second error, four minutes for the third…)
Af ter first code introduction, some confi gurations must be programmed ( see chapter”
configuration”). These are remaining programmed till battery disconnection.
NOTE : the return to the “wave jammer” mode is possible by simultaneously push-
ing of the keys 2 and 5, putting the radio under tension. Wait then for two minutes.
Programming
OBSERVATION : in order to select the radio operation are a, push simultaneously keys 2
and 5, putting the radio under tension. Wait then for about two minutes. Introduce the four digits
code, then:
-s elect the adequate area
86 - 2
25
-America
-Japab
-Asia
-Arabia
-Othe rs (Europa, Africa, others…)
-Select the sound tonality curves:
- 0 : inactive adjustment
- 1 : Tw i n g o
- 2 : Clio
- 3 : Mégane
- 4 : Laguna
- 5 :
T op ra nge
- speakers number configura tion – with or
w ithout rear speakers (REAR ON / OFF)
NOTE : it is not necessary to perform the configuration after radio code introduction,
further to a supply failure.
vnx.su
