2004 DACIA SUPERNOVA door lock

72
SIDE OPENINGS ELEMENTS TRIM
72-2
DISMOUNTING
Rear door panel replacement is pe rformed without the dismounting of t he door, a nd the
following operations are to be performed :
Dismount the window regulator crank (2) that is mounted by clips attachment on the window
regulator axle. Dismount the inner opening mechanism (3), by dismounting the screw (4) and detaching from
the inner opening mechanism, the rear door opening control rod, which is fixed on the plate with
the other end.
Dismount the locking handle (5).
Dismount the screws (6 ) remove the panel by detaching it from the caisson of the door.
Dismount the guiding case (8) and the locking button (7).
REMOUNTING
Pe rform in the reverse order the dismounting operations taking into account the following
recommendations: -for the m ounting of t he outside opening mechanism, t he opening control rod will be
placed in the position where the assembled plate with electric control is unblocked. -after mounting, check the operation of the internal opening mechanism and its alignment
w ith the rear door panel.
NOTE
The window regulator crank must be placed in horizontal position with the button
oriented toward front, the window being closed.
REAR DOOR PANEL
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 1
This type of anti starting syste m is based on the key recognition, which has a special construction.
It may be separated in two elements which can be identified in the following way (pict.1): the key
he ad (pos.A.) made of plastic, which can be dismounted and the metal insertion (pos.B.), which is
fixed an d ensured by clipping in the key head.
In the key head, there is a coded independent electronic circuit, which is functioning without
battery. When setting the contact on, the anti starting bushing, placed around the starting contact,
is enquiring and catching the coded signal emitted by the key head, then sends it to the Electronic
Control Unit (E.C.U.) decoder. This one is attached on the front left pillar, under the lower casing
of the dashboard and has the function of receiving the code sent from the bushing. If the decoder
recognises the key code then it will send a coded signal to the injection computer, which compares
it with the previous memorised code and will authorise or not the start of the engine.
We mention that the system with radio frequency remote control (RF) of the doors blocking
/unlocking, has no influence to the anti starting system. In this case, the key head has a different
construction, having an activation button of the remote control and a red LED, which is lighted in
the moment of blocking/unlocking the doors, by pushing the key button. Inside the key head
there is the coded electronic circuit for the anti starting system and an imprinted electronic circuit,
s upplied by a battery, for t he RF remote control operation of blocking/unlocking the ve hicle
doors.
The anti starting system is activated after approximate 10 seconds from the breaking of the
contact and is visualised by the blinking of the anti starting indicator placed on the instrument
panel.
If the battery is low charged, the t ension drop on the starter, at starting,
may cause the activation of the anti starting system and the start of the engine is
impossible.
pict.1
GENERALITIES
AT T ENTION
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 3
GENERALITIES
The anti starting bushing (picture 5) is located around the starting contact a nd is accessible
after the dismounting the steering wheel’s cases. It catches the signal from the key head and then
s ends a coded signal t o the E .C.U. decoder.
The vehicles equipped with RF remote control keys for blocking/ unlocking t he doors are
provided with another anti starting bushing which transmits to the E.C.U. decoder also the signal
received from the RF remote control.
The recognition of the two types of decoding bushings is realised by means of codes labelled
on their body, as follows :
- code 042264J - for vehicles w ithout RF remote control
- code 8200044257 - for vehicles with RF remote control
The E.C.U. decoder (picture 6) has the
following functions :
- decode the signal received from the anti
starting bushing ;
- sends a c ode to the injection computer
in order to authorise the engine starting.
- controls the anti starting indicator of the
instrument panel - receives the coded signal from the anti
NOTE
In case both keys we re lost, the code of the key head (8 characters) and the code of
the m etal insertion (4 characters) can be red from the vehicle invoice. If al so the i nvoice
was lost, the two mentioned codes can be found out based on the chassis series number
of that vehicle, accessing the database of the DACIA manufacturer, calling the TECH
LINE.
pict.5
pict.6
starting bearings, for the vehicles equipped with RF remote control;
- commands the blocking/unlocking of the doors, if the vehicle is provided with RF remote
control keys;
- commands the dome ceiling lighting, for the vehicles equipped with this system.
E.C.U. DECODER
ANTI STARTING BUSHING
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 4
NOTE :
The vehicles equipped with this anti starting system, have a type of decoder, and those
provided also with RF remote control for locking/ unlocking doors have another type
of decoder.
The identification of the two types of E.C.U. de coder i s realised by the inscriptions on
the labels as fol lows: -code P8200032783H and the inscription TRANS-PLAF for the vehicles without
RF remote control ;
-code P82000 32776H and the inscription TRF-TRANS-CAR for the vehicles
with RF remote control.
ANTI STARTING INDICATOR
It is located on the instrument panel (picture 8, position A) and has the following functions: - signals the activation of the anti starting system
- signals the case of non identifying the key head
- signals the entrance in the operation mode “resynchronisation” of the remote controls,
RF with E.C.U. decoder, for the vehicles which use the RF remote control.
pict.7
pict.8
A
GENERALITIES
The dome ceiling lighting is activated subject to the position of the switch
(picture 7, position 1):
- position A the ceiling lights permanently
- position B the ceiling turned off
- position C dome ceiling lighting; this will light for 5 seconds after a front door closing or
after the command of unlocking the doors with the RF remote control. This delay turns out in the
moment of setting the contact.
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 6
Af
ter ordering a new key head based on the alphanumeric code mentioned on the i nvoice,
dismount the old key head and remove the metal insertion (mechanical part), then introduce the
old metal insertion in the new key head according to t he previously mentioned procedure. In
case the key head is provided with RF remote control for blocking/ unlocking the doors, after its
replacement, perform the synchronising procedure of the RF remote control with the decoder,
subject to the following cases:
(a)- the vehicle has a key with RF remote control and one without RF remote control; in this
case after the replacement of the RF key, perform the “simple synchronised procedure” in order
to bring into phase the RF remote control with the decoder.
( b)- the vehicle has two keys with RF remote control; after the replacement of one RF key,
perform the “specific synchronised procedure”;
(c)- the vehicle has two keys with RF remote control; if both keys are replaced, perform the
“simple s ynchronised procedure for the firs key and the “specific synchronised procedure” for
the second one. If a key was lost, a new key head and a metal insertion will be ordered. KEY HEAD REPLACEMENT
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 7
A
ll the new decoders, are not coded. After t he mounting on the vehicle it is necessary the
memori sation of t he key head code by the decoder i n order to be operational. If only the
decoder is replaced, no intervention is necessary to the injection computer, which will keep the
old anti starting code. When the vehicle is provided with RF remote control for blocking/unlocking
the doors, the performing of the resynchronisation of the keys with the decoder is imposed, after
its mounting.
If further to the diagnostic of the anti starting system, using the CLIP tester, the replacement of
the decoder is imposed, proceed as follows: - disconnect the front wiring connector from the E.C.U. decoder ( the contact being off);
- dismount the attachment screws of the E. C. U. decoder on the front left pillar;
- mount the new E.C.U. decoder;
- connect the front wiring to the new decoder.
Proceed then to the insertion of the anti starting code using the contact key, then to its memorising
(validation) in the E.C.U. decoder, using the CLIP tester. For this purpose, perform the “E.C.U.
decoder re placement procedure and a nti starting c ode memorising”. Che ck then the correct
operation of the anti starting system with both keys. E.C.U. DECODER REPLACEMENT
AT TENT ION
Once the decoder has memorised the key codes, this code cannot be erased
or replaced with another one.
If it is necessary the replacement of the kit (E.C.U. decoder and two key heads), after that
realise t he “ Kit replacement procedure”.
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 9
The RF remote control has no influence on anti starting system. It has only the function of
blocking/ unlocking the doors. The RF remote control with evolutionary code can use only two
keys as the decoder may manage only two different evolutionary codes. The key heads have an identification number formed by 8 alphanumeric characters (letters
and figures) , beginning with letter E.
In case of loosing one key, a key head and a metal insert ion will be ordered, then the
resynchronisation procedure of the RF remote control of t he ke y with t he decoder from the
vehicle must be performed. If the vehicle is provided with RF remote control key and this one
has been replaced, then perform the “ Simple synchronised procedure “. When the vehicle has
both keys with RF remote control, then perform the “Specific synchronised procedure “ after the
replacement of the second key.
NOTE - In the case only one ke y head is replaced, usually there is no need for
r esynchronisation of the other RF remote control.
- If both RF remote controls are desynchronised, one procedure of resynchronisation
will be performed with each remote control: perform the “Simple synchronisation
procedure for the first RF remote control” and the “Specific synchronisation procedure”
for the second RF remote control. Check then t he operation of blocking/ unlocking of the doors with both RF remote
controls. RF REMOTE CONTROL FOR BLOCKING/ UNLOCLING
THE DOORS
vnx.su

82A
HORN - ENGINE IMMOBILISER
82A - 11
A.
ECU DECODER REPLACEMENT PROCEDURE AND ANTI STARTING
CODE MEMORISING
The new E.C.U. decoder is always not coded. After its mounting on the vehicle it is necessary
that this one is memorising the anti starting code in order to be operational.
NOTE
If only the E.C.U. decoder i s replaced, there i s no need of an i ntervention to t he
E.C.U. injection (injection computer), which will keep the old anti starting code.
AT TENT ION
After the E.C.U. de coder memorised the anti starting c ode, this code cannot be erased
or replaced with another one.
In order t o perform this procedure, one of the keys of t he ve hicle and the CLIP tester are
needed. Perform as follows: 1. Connect the CLIP tester to the diagnostic socket and to the battery (or the lighter
socket) of the vehicle. 2. Read the configuration of the old E.C.U. decoder in the following way, before dismounting
it from the vehicle:
- select t he type “SUPERNOVA” and the “050” equipping level;
- enter the menu “ COMPUTER TEST” then choose “ ANTI STARTING”
- access “COMMAND MODE” then “CONFIGURATIONS READING”
- note the configurations found : petrol/d iesel, programming with 1 or 2 keys, ceiling delay,
the type of the doors’ blocking switch (CPE), etc.;
3. Get back to the m enu “TEST COMPUTERS”
4. Remove the old E .C.U. decoder and replace it with a new one, the contact being off.
5. Enter the menu “ANTI STARTING”, then select “ STATE LIST”. If the E.C.U. decoder
is new, you must find the following states:
18G FIRST CYCLE MEMORISING………………........................ ACTIVE
19G NOT PERFORMED KEY PROGRAMMING……………….. ACTIVE
19D UNLOCKED KEY PROGRAMMING………………............. ACTIVE
OBSERVAT ION
If the states 19G and 19D are not “ACTIVE” this means the E.C.U. decoder has
been already used, so it isn’t new and cannot memorise another anti starting code.
Access the menu “COMMAND MODE” and then “CONFIGURA TION”, where you will
configure the new E.C.U. decoder in the same way as the old one: petrol, 1 key, ceiling delay,
impulsion doors blocking switch, etc. selecting one by one these configurations, which you’ll
validate with “CLICK” on the blue button on right top of the screen. PROCEDURES
vnx.su