2004 DACIA SOLENZA fuse

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 34
Diag nostic
ALP 8. TURNING LIGHTS DO NOT SWITCH ON AT THE BLOCKING /
UNLOCKING OF THE DOORS
RECOMMENDATION Check the absence of the failures with the CLIP tester. If there are failures, fix them first.
Check if the synchronisation of the RF remote control and the E.C.U. decoder has been
performed.
Are the turning lights functioning normally at the activation of the signalling switch ?
Check the continuity and the isolation
related to t he mass and the +12 V of the
electric layout:
E.C.U. decoder FLASH relay
Pin B3 pole 2
Is it correct?
Repair the signalling system.
Check t he fuse F03 and F04.
Fix the electric layout.
Check the fuse F02 condition from the cockpit
fuse box.
Is it good?Replace the fuse.
Di sconnect the FLASH relay. Supply with
+12, the pole 4 of the relay. Are the left turning
lights turning on? Supply with +12 V the pole
5 of the signal relay. Are the right/left turning
lights turning on?
Repair the electric layout from
poles 4 and 5 of the FLASH relay.
Replace the FLASH relay.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
No
No
No
Yes
Yes
Yes
Yes No
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 54
RECOMMENDATIONS Applying conditions of the diagnostic to the memorized failure:

- fa ilure declared present when setting the contact on (+After contact).
Diagnostic – Failures interpretation
DF 069
PRESENT OR
MEMORIZED UCH CONNECTION ANTI-STARTING BUSHING
CC.O: short-circuit at m ass
CC.1: short-circ uit a t 12 V
CC.0Check the condition and connection f the anti-starting bushing
If necessary, repair the connector.
Check the connection and condition of the connector with 40 pins
EH1 of the Cockpit Central Unit
Repair the connector if necessary.
Disconnect the bushing connector and check the correct supply of
+ 12V at pin 3 bushing connector
Fix it if necessary.
Check the continuity and insulation of the connection between:
Cockpit fuse box F04 (15A) pin 3 bushing
Fix it if necessary.
CC.1Check the connection and condition of the bushing connector.
Fix the connector condition if necessary.
Check the connection and condition of connector 40 pins EH1 of
Cockpit Central Unit.
Fix the connector if necessary.
Check the continuity of the connections between:
mass pin 2 bushing
Connector 40 pi ns EH1 of UCH pin A16 pin 4 bushing
Fix if necessary.
AFTER REPAIRING Apply the recommendation Fix all others failures
Erase the memorized failures.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 58
Diagnostic – States interpretation
RECOMMENDATIONS Nothing to notice
ET154 I NACTIVE with contact on.
Pe rform the checking of F13 fuse 925A) n the cockpit fuse box.
Check by means of a multiple meter presence of +12 V with the contact on, at the level of fuse
socket.
Fix if necessary.
Check by means of a multiple meter presence of +12V with contact on a t pin A3 of the P1
connector of the cockpit Central Unit
If voltage is present, replace the Cockpit Central Unit
If there is no voltage, ensure the continuity and insulation at mass between pin a3 of the P1
connector of UCH and fuse F13 (25A) from cockpit fuse box.
Fix if necessary.
ET154 ACTIVE with contact off.
Check by means of a multiple meter absence of +12 V w ith contact off at the level of F 13
fuse socket from cockpit fuse box.
Fix if necessary.
If there is no voltage, replace the Cockpit Central Unit
ET154
PRESENCE + 12 V AFTER CONTACT
Perform again a system diagnostic
Fix all others failures
Erase the memorized failures.
AFTER REPAIRING
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 63
Diagnostic – Damage location algorithm
AL P1
There is no communication with the computer
RECOMMENDATIONS Nothing to notice
Check the communication of CLIP tester with a computer from another vehicle.
Check:
- connection between CLIP tester and the diagnostic socket (check the cable c ondition).
Cockpit and engine compartment fuses.
Check presence +1 2 volts befor e c ontact at pin 16, + 12 volts after contact at pin 1
and mass at pins 4 and 5 of the di agnostic socket
Fix it if necessary.
Connect the multi-socket and check the insulation, continuity and absence of parasite resis-
tance at connections:
Pin A3 of UCH connector P1 with 15 pins fuse box
Pin 22 of UCH connector E H1 with 40 pins + after contact
Pin A1 of UCH connector P1 with 15 pins mass
Pin 34 of UCH connector EH1 with 40 pins pin 7 diagnostic socket (line K).
Fix it if necessary.
Check the system operation
AFTER REPAIRING
vnx.su

85
WINDSCR EEN WIPER
85 - 3
Replace
fuse F 07 Check fuse F07 from cockpit.
Is it good?
Replace the under steering wheel control assembly .
Replace the windscreen wiper timer. Check the windscreen wiper
switch. Is it good?
Check the windscreen wiper timer. Is i t good?
Replace the windscreen
wiper electric motor.. Is there any 12 V between pins 5
and 1 of the electric
motor connector
of the windscreen wiper ? S
et the contact on. Switch the
windscreen wiper on highs peed. Is the windscreen
wiper working?
Set the contact off.
Check the continuity and the resistance against the vehicle mass
betw een:
- exit fu se F07 pin A7 windscreen wiper switch
- pin A2 windscreen wi per switch pin 5 electric motor
connector of the windscreen wiper;
- pin 1 electric motor connector of the windscreen wiper
ve hicle mass.
Are they good?
Defective wiring. Fix it.
Replace the windscreen
electric motor. Is there any 12 V between pins 4 and
1 of the electric motor connector of
the windscreen wiper?
S et the contact off.
Check the continuity and the resistance against the vehicle
mass between:
- exit fuse F07 pin A7 windscreen wiper switch
- pin A3 windscreen wiper switch pin 4 electri c motor
connector of the windscreen wiper;
- pin 1 electric motor connector of the windscreen wiper
vehicle mass. Are they good? Switch
the windscreen wiper
on low speed. Is the
windscreen wiper working ?
Defective wiring. Fix it.
No
NoNo
No
No
No
No No
No Ye s
Ye s
Ye s
Ye s
Da
1
Ye s Ye s
Diag nostic
vnx.su

WINDSCR EEN WIPER
85
85 - 4
S
et the contact off.
Check the continuity and the resistance against vehicle mass
between:
- exit fuse F02 pin 3 electric m otor c onnector of the
windscreen wiper
- pin 2 electric m otor connector of t he windscreen wiper pin 4
timer connector of the windscreen wiper;
- pin 3 timer connector of the windscreen wiper pin 6 switch
connector of the windscreen wiper.
Ar e they good?
Defective wiring. Fix it.
Replace the windscreen wiper timer. Is there any 12 V between
pins 9 and 1 of the timer connector of the
windscreen wiper
?
S et the contact off.
Check the continuity and the resistance against vehicle mass between:
- exit fuse F07 pin A7 switch connector of the windscreen wiper;
- pin A1 switch connector of the windscreen wiper pin 9 timer
connector of the windscreen wiper;
- pin 1 timer c onnector of the windscreen wiper vehicle m ass;
- pin 5 timer connector of the windscreen wiper exit fuse F 07.
Ar e they good ?
Defective wiring. Fix it.
Replace the windscreen washing reservoir. Is there any 12 V between pins 1 and
2 of the electri c pump connector of
the windscreen washing?
S et the contact off.
Check the continuity and resistance against vehicle mass between:
- exit fuse F07 pin B4 of the switch connector of the windscreen
wiper.
- pin A4 switch connector of the windscre en wiper pi n 2 e lectric
pump connector of the windscreen washing;
- pin A4 switch connector of the windscre en wiper pin 2 timer
connector of the windscreen wiper;
- pin 1 electric pump connector of the windscreen washing vehicle
mass;
- pin 5 timer connector of the windscreen wiper exit fuse F07.
Ar e they good? Electromotorul
º tergãtor parbriz
“se opreºte l a punct
fix”?
Switch the windscreen wiper
on timer position.
Is the windscreen wiper electric motor working delayed?
Switch the windscreen
wiper on windscreen
washing position. Is the
windscreen washing
electric pump working?
Cablajul
este defect.
Rem edi a πi.
1
No
No
No No
No
No
No
No
Ye s
Ye s Ye sYe s
Diag nostic
vnx.su

86
86 - 7
AUTO RA DIO
CD P LAYER
CD (compact disc) playing.
Insert the CD, with the recorded face downward, in the door located on the device front part.
The CD lecture is beginning with track number 1.
If the CD has been previously inserted, then you switch on listening to a radio station, in case
you wish to listen again to the CD, push key SRC and select CD. The CD playing will continue
from its last stop.
After listening the last CD track, the playing is continuing beginning with track no.1.
Observations:
- The CD playing may be interrupted by the receipted information if radio has been previously
programmed to operate” Emergency messages reception”.
- If you after inserting the CD, you hear an acoustic signal (bip), check if the CD is not dirty
or damaged.
Track selection
In order t o select the de sired t rack, push consequently > or < till you reach the searched
track. The CD lecture will continue from the selected track.
Fast forwards/back wards
Push key > or < and maintain it pushed, performing in this way, the forwards and consequently
backwards of the track listen in that moment.
CD tracks random playing
In order to activate this function, push ke y ( 1). After finishing random playing of all CD
tracks, the lecture will c ontinue until its stop controlling. If key > is pushed, passing to the next
track, random selected, will be performed. If key < is pushed, playing again of the existent track
will be performed. In order to return to the normal track playing ( successive playing), key (1) i s
to be pushed and to be maintained for few seconds.
CD eject.
After CD playing, if CD ejection is desired, push key (2) EJECT, placed on the left side of
the device front panel.
OBSERVATIONS:
This CD player is reading only CD audio parts. If on CD there are also non-audio parts, they
can not be red and on the display the track number followed by the message NO AUDIO will be
displayed.
If a CD without a ny audio t rack, i s inserted in CD player, this one will be refused and the
message NO AUDIO will be displayed on the screen.
This CD player is operating only with 12-cm diameter CD.
CD Player
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 2
DISMOUNTING
Disconnect the battery (-) terminal.
Pull the seat ( 1) of the access flap ( 2) to the fuse box locate d in the cockpit, at the left end of the
dashboard. Carefully remove flap ( 2).
Dismount the attaching screw ( 3) of the fuse box on the driving post cross-beam, lift it from seat ( 4) and
carefully remove it.
REMOU NT I NG
Attach the assembly on the driving post crossbeam in its seat ( 4) and mount the screw (3).
Ca refully mount back, the access flap ( 2) to the fuse box.
Re connect the battery (-) te rminal.
Pe rform functional tests, noticing the correct operation of all consumers supplied by means of the cockpit
relays assembly and UCE decoder.
Relays and UCE decoder assembly from cockpit
2
1
3
vnx.su