2004 DACIA SOLENZA steering

VA LUES AND ADJUSTMENTS
07
07 - 9
Checking values of the rear axle angles
ADJUSTMENTS
Not adjustable
N ot adjustable
VEHICLE
POSITION
Unloaded
Unloaded
Unloaded
VA L U ES
0030' ± 10'
(For two wheels) Cl osing
0
030' ± 10'
2,9 mm ± 1 mm
ANG L E S
CAMBER
PARALLELISM
ELASTIC BUSHINGS TIGHTENING
PRELIMINARY OPERATIONS TO BE OBSERVED BEFORE
CHECKING THE STEERING ANGLES
1. Area (checking surface) – it must be a s horizontal as possible.
2. Wheels, tires – check (from e quipping point of vi ew) to have same type of wheels and
tires on bot h axles (dimensions, inflating pressure, wear de gree). A pronounced wear i s not
allowing the correct horizontal positioning.
3. Suspension – check the shock absorbers, springs condition and height symmetry under
carriage body.
4. Joints – check the e lastic joints condition, steering and suspension ball joints clearance,
bearings clearances of the front and rear axles 5. Radial and axial run out of the wheels – must not be over 1 mm. This will be compensated
with the reading instruments. 6. Manufacturer’s method – each vehicle manufacturer is providing the checking conditions,
axles weights repartition, and presentation of under carriage body heights, not loaded.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 4
Power train group
The power train dismounting-remounting is to be performed on the engine compartment upper
part by means of a mobile lifting device.
The vehicle i s to be placed on a 2–columns
elevator.
Dismo unt :
- battery
- air filter inlet pipe;
- air filter assembly ;
- engine bonnet;
- front wheels.
Disconnect the oxygen sensor ( 1) connector
or the connectors of the two oxyge n sensors
(EURO 00 ).
Di smount : thermal protection screen and
descending tube from the exhaust manifold.
DISMOUNTIN G
Drain:
- the cooling circuit on the water pump
inlet pipe; - oil from gearbox;
- oil from engine if necessary;
- refrigerant fluid to a charging station
(vehicles with AC);
- oil from the power steering circuit
(vehicles with power steering).
- Oil from the power steeri ng circuit
(vehicles with power steering);
Dismo unt :
- engine shield;
- descending tube attachment screws
on support;
TIGHTENING MOMENTS) (daNm)
Right support attachment screw on engine 6.2
Hydr o-elastic buffer attachment nut 3.7
Left elastic buffer attachment nut 6.2
Whe els s c rew s 7.5
Power train- battery attachment screws 2.1
Connecting rod attachment nut on steering cross member support 6.2
Anti-roll connecting rod attachment screw on gearbox connecting rod 10.5
Control bar attachment screw on gearbox connecting rod 2.7
Pipes a ttachme nt s crews on comp ressor 2.1
High pressure pipe on DA pump 2.1
1
23
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 5
Power train group
Sw ing over the steeri ng knuckle and
extract the pl anetary t ransmission from the
planetary pinion of the gearbox. Dismount the left planetary transmission,
as follows: - dismount the steering knuckle nut;
- dismount the planetary transmission
attachment screws on the gearbox;
- dismount the brake calliper assembly ;
- dismount the shock absorber two
attachment screws on steering knuckle;
- swing over the steering knuckle and
dismount the planetary transmission. Dismount t he fuse box from the engine
compartment.
5
6
- collar ( 2) between the descending
tube and expansion chamber, remove the
descending tube; -anti-roll connecting rod.
Di sconnect the re verse dri ving contact
connector. Disenga ge the right planetary transmission,
as follows:
-dismount the brake calliper assembly ;
- dismount t he shock absorber t wo
attachment screw (4) on steering knuckle. Disconnect:
- connector (5 ) from the UCE (pull flap
(6) and then disengage); - engine wiring from engine fuse box;
4
- shock sensor connector;
- cooling engine fan connector;
- DA pressure sensor connector;
- mass wire from the gearbox
Dismount the battery protection shield.
Disconnect by means of the elastic clips pliers
MOT.1202-01 :
- hoses from radiator;
- hoses from thermostat support and from
water pump inlet pipe;
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 7
Power train group
Dismount the hydro-elastic buffer nut (on
the right side).
Remove the power train and place it on a
support.
Disco n nect th e pr e ssu re controller
connector for power steering.
Dismo unt :
- hoses from oil reservoi r for power
s teering by means of pliers MOT 1202-01;
- high pressure pipe from the power
steering pump.
Dismount the refrigerant fluid pipes from
compressor (vehicles with AC unit).
Sustain the power t rain by means of the
two liftin g supports u sing a mobile lifting device
(mobile crane). Dismount the four attachment screws of the
power train support-battery and the elastic bu ffer
nut (9).
9
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 8
Power train group
REMOU NT I NG
Perform the dismounting operations in the reverse order.
Tighten the screws and nuts to the required moment.
Perform: -filling and purging of the cooling circuit (see chapter 19”Filling a nd purging”);
-f illing with oil of the engine and gearbox;
-f illing of the power steering circuit (see chapter 05 “ Draining-Filling)- for vehicles
equipped with power steering;
-filling of the air conditioning circuit with refrigerant fluid HFC 134a (see chapter 62 “Air
conditioning”). Adjust the clutch pedal stroke (see chapter 37”Clutch control adjustment”).
REMARK:
At each operation implying battery dismounting, when reconnecting the battery,
introduce the radio code, which is written on the vehicle-purchasing invoice.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 21
CYLINDER HEA D DISMOUNTING
Drain the oil from the engine.
Dismount :
- wiring from the engine;
- compressor and/or power steering pump ( for vehicles equipped with air conditioning
unit and/or power steering); -compressor support and/or power steering pump support;
- alternator and its belt.
Dismounting – Remounting
Block the engine flywheel by means of the
MOT 582 device .
Dismou nt :
- oil dipper rod support;
- alternator belt tightening clamp;
-cr ankshaft pulley or pulleys ;
- pulley hub;
- distribution belt casings.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 38
2. Camshaft gear with marks
Rotate the engine until is reaching the Upper
Dead Point (cylinder 1 at ignition), and then con-
tinue until first item:
- adjust : exhaust 1
exhaust 3
- at second item :
-adjust : admission 1
admission 3
- at third item :
- adjust : exhaust 2
exhaust 4
- at fourth item :
- adjust : admission 2
admission 4
Dismounting – Remounting
Continue to mount:
- cylinder head cover equipped with a ne w cylinder head gasket, tighten the attachment
sc rews to the required moment of 1 daNm;
- water inlet pipe and the oil dipper guide (with new sealing rings);
- distribution casings;
-cr ankshaft pulley or pulleys; tighten the pulley hub screw to the required moment of 2
daN m, then to 68° ± 6°.
ATTENTION!
If the screw is not properly tighten, this may unloose, which may lead to the oil pump
no n-drive and to the distribution derangement, consequently to engine damaging.
- intake manifold and exhaust manifold, tighten the attachmen t screws to the required mo-
ment of 2.5 daNm;
- compressor and/or power steering support;
- alternator (see chapter 16”Alternator”);
- compressor- for vehicles equipped with air conditioning (see chapter 62 “Air condition-
ing”); -power steering pump-for vehicles equipped with power steering (see chapter 36 “Power
steering pump”);
-belt or accessories belt according to the method described in chapter 07” Accessories
b elt tensioning”.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 42
Multi-purpose support
TIGHTENI NG MOMENTS (daNm)
Sup port attachment screws 4
Sup port upper attachment screws 2
DISMOUNTIN G
Place t he vehicle on a two-column elevator.
Disconnect the battery.
Dismount :
-compressor (see chapter 62”Air
conditioning ”) for vehicles equipped with a ir
conditioning unit; -power steering pump (see chapter 36 “
Power steering pump”) for vehicles equipped
with power steering.
- Dismoun t the support attachment screws.
2
2
REMOU NT I NG
Position the support and pre-tighten the
central screw (1) to the required moment of
0.25 daNm. Mount the others attachment screws.
Tighten to the required moment observing
the sequence shown in the drawing. Remount the other elements by
performing the dismounting operations in the
reverse order.
Supp Support AD S
upport AC/AD
vnx.su