2004 DACIA SOLENZA ignition

IGNITION AND INJECTION
17
17 - 7
Injection system
In the fuse box located in the engine compartment, the following relays may be identified:
A. Co mpressor relay
B. Engine c ooling fan relay, step I
C. Engine cooling fan relay, step II
D. UCE injection relay, canister-purging valve
E. Fog projectors relay
H. Fuel pump and ignition coil relay
14. C arbon canister with purging valve
included
;
16.
Power steering pressure controller; 12.
Oxygen sensor;
15.
A ir conditioning pressure controller.
1
15
12
1614
vnx.su

IGNITION AND INJECTION
17
17 - 8
Injection system
WATER TEMPERATURE SENSOR
The water temperature sensor ( 1) is sending to UCE injection the information regarding water tempera-
tu re, and another information is sent to the indicator from the instrument panel, which will show the water
tem perature.
In case of an alert regarding the water temperature, UCE injection will control the lightening of
the water temperature indicator from the instrument panel.
Subject to water temperature, UCE injection will control:
- injection system;
- relays for controlling the engine cooling fan.
When setting the contact on, the water temperature indicator located on the instrument panel,
will be lighted for 3 seconds, then it will turn off.
1
1
If after the contact is set off, in the next 2 minutes from engine stopping, the water temperature
is reaching 102 °C, and t hen the injection computer i s control ling t he starting of the e ngine
cooling fan at low speed. When the temperature is lowering at 95°C, the engine cooling fan stopping will be controlled;
its operation must not exceed 10 minutes after engine stopping.
vnx.su

IGNITION AND INJECTION
17
17 - 9
ANTI-STARTING INDICATOR
When setting the contact on, UCE injection is receiving from UCE DECODER a code, whi
ch is compared
with the one previously memorized; if the two codes are matching, then the engine starting is author ized.
After contact setting on, anti-starting indicator which was previously blinking, will light for
three seconds then it will go off, confirming in this way, the key recognizing.
If the key is not good, after setting on the contact, the anti-starting indicator will start blinking
faster and the engine starting will be impossible.
OBSERVATION:
For details regarding the vehicle anti-starting system, see chapter 82 “Anti-starting system”.
AT T E N T I ON!
U CE injection c onnecting or disconnecting to t he vehicle’s wiring i s to be pe rformed
Injection system
only when the engine is stopped and t he contact off.
If the contact is on or the engine is running, do not loosen or disconnect the battery
terminal s. It is forbidden the battery replacement on t he vehicle i f the engine is running
or the contact on. Loosen or rusty contacts at battery terminals and imperfect connections at the
injection system wiring are not allowed. It is forbidden the engine starting with the battery connected to a charging / starting
unit. The battery recharging is t o be pe rformed only aft er disconnecting it from the vehicle
wiring and by means of a c harging unit with 12 V v oltage.
vnx.su

IGNITION AND INJECTION
17
17 - 10
MU LTI-POINT INJE CT ION CHARACT E RISTICS
〈 SIRIUS 32 with 90 pins computer is managing the ignition and the injection.
〈 For diagnostic, CLIP Sagem tester is to be used.
〈 The injection system in use is a sequential multi-point type, injection and ignition phases
controlling being based on the SIRIUS 32 computer program logic, starting from the signal received
from the RPM sensor.
〈The pr esence of the anti-pollution indicator OBD on the instrument panel, that is lighted for
3 seconds when setting the contact on, is specific to the vehicles observing pollution norms EURO
2000. The injection computer of these vehicles is provided with diagnostic system type OBD (“ On
Board Diagnostic).
〈 Idling regime correction is subject to:
-c limate maintenance on/off control (air conditioning)
-e lectrical balance on vehicle, as a result of connecting different electric consumers.
〈 EURO 2000 specific vehicles are provided with two oxygen sensors located in front of the
cata lyst (upstream oxygen sensor) and after catalyst (downstream oxygen sensor).
〈 At EURO 2000 specific vehicles, the fuel supply is performed at constant pressure (3.5 ±
0.2 bar), the pressure controller placed in the fuel tank being provided for this purpose.
Chara cteristics
vnx.su

IGNITION AND INJECTION
17
17 - 11
AIR CONDITIONING UNIT IS USING A COMPRESSOR
WITH VARIAB LE DI SPLACE M ENT
Th e connections injection/air conditioning, are the followings:
- pin 46 of the injection computer is receiving the information “ air conditioning
re que st” further to the air conditioning switch acting;
- pin 10 of the injection computer will transmit the coupling control of the air
co nditioning compressor by means of the “A” relay, if the coupling authorization conditions are
accomplished.
The information “power absorbed by compressor” displayed when performing diagnostic by
means of the CLIP tester, is related to the couple value taken by the compressor. This is of 300-
5000W, the minimal displayed value being of 300 W, regardless the compressor coupled / unc oupled
c ondition.
Th e injection computer is forbidding the compressor coupling in the following situations:
-at less than 16 seconds from engine starting;
-subject to the power requested to the engine by the vehicle driver.
-when th e acceleration pedal is fully pressed;
-i f the engine RPM is lowering till 550 rot/min (compressor is again coupling if the RPM is
r eachi ng to 1800 rot/min);
-if the wa ter temperature has increased to over 110° C;
-if the engi ne RPM is exceeding 6000 rot/min.
Injection / air conditioning strategy
vnx.su

IGNITION AND INJECTION
17
17 - 12
IDLING REGIME CORRECT ION SUB JECT TO B ATTERY VOLTAGE AND TO
ELECTRI C BA LANCE ON VEHICL E.
Th is correction is dedicated to the compensation of the voltage drop due to the electric consumers
starting, when the battery is weaker charged. In this purpose, engine RPM is increased, allowing in
this way the alternator rotation increase and consequently of the battery voltage.
More the lower is the voltage, more important the applied correction is. So, a variable correction
is applied, starting when voltage is reaching 12,8 V. The correction is starting from the nominal
idling RPM and may increase with maximum 150 rot/min additional.
Idling regime correction
vnx.su

IGNITION AND INJECTION
17
17 - 13
PRINCIPLE
In engine normal operation conditions at warm, the RC O value is varying between a high and
a low limit, in order to obtain the nominal idling regime. Further to an operation dispersion
(ru nning in, engine clogging, etc), it may be possible that RCO idling value to be situated next to
the lower and higher values. The ad aptive correction of the “RCO idling ” parameter is allowing obtaining of slow variations
of the engine air requirement, so that RCO value centering on an average nominal vale is obtained.
Th is correction is becoming effective unless the water temperature is over 80°C, at 20 seconds
after engine starting and if it is in the nominal idling adjustment phase.
“R CO IDLING” AND “ IDLING EN RICHING ADAPTATION” VALUES
PARA M E T ER RE COM MENDE D VAL UE
PR006: Engine regime 750 rot/min
PR022: RCO idling 5%< X < 12%
PR031: Idling enriching adaptation 80 < X < 176
At each engine stopping, the injection computer is controlling the performing of a new position-
ing of the step-by-step engine, bringing it to the bottom limit. This function so called “re-setting”, is
main tained for 8 seconds.
INTERPRETATION OF T HE PREV IOUSLY M ENT IONED PARAM ETERS
In the situation of an air excess (infiltration air, valve body inadequate attachment, etc), the idling
re gi me will increase and the “RCO idling” va lue will decrease in order to return to the nominal
idling regime. The value of the RC O idling adaptive correction will decrease in order to centering
again the id ling adjustment operation.
In case of an air lack (clogging, etc) the reasoning is opposite: “ RCO idling” is increasing, and
the value of the “ RCO idling” adaptive correction will increase in order to center again the idling
opera tion on an average nominal value.
IMPORTANT: After erasing the failures memorized by the injection computer, it is necessary
to start the engine then stop it, in order to achieve in this way the re-setting of the step-by-step
en gine. Start then again the engine and let it idle run until reaching the nominal idling regime, in
or der to achieve a correct re-setting of the adaptive correction.
Idling regime adaptive correction
vnx.su

IGNITION AND INJECTION
17
17 - 14
The e ngines equipped with UCE injection type SIRIUS 32 are provided with oxygen sensors, as
follows:
-one up stream oxygen sensor – for engines corresponding to EURO 96 de-pollution norms.
- one upstream oxygen sensor and one downstream oxygen sensor – for engine s corresponding
to EURO 2000 de-pollution norms.
OXYGEN SENSORS HEATING
Oxygen sensors heating control is given by UCE injection as follows: -for up stream oxygen sensor – starting with engine starting.
-f or downstream oxygen sensor – after a certain time from engine starting, imposed by the
UCE injection charts, being subject to engine RPM and water temperature, red only when the
accelera tion pedal is not released.
UPSTREAM OXYGEN SENSOR VOLTAGE
After connecting the CLIP tester select “ Injection Diagnostic” and refer to “PR009 parameter:
Upstream oxygen sensor voltage”. The displayed value, expressed in mV, is representing the voltage
supplied towards UCE injection by the oxygen sensor placed upstream as the catalyst. When the
engine is running in the “closed loop” phase, voltage must fluctuate quickly between the following
lim i ts :
-20 mV ± 50 for poor fuel mixture;
-840 mV ± 70 for rich fuel mixture.
Smaller is the difference between these two limits, less good the sensor information is
(g en erally this difference is of 500 mV).
DOWNSTREAM OXYGEN SENSOR VOLTAGE
After connecting the CLIP tester select “ Injection Diagnostic” and refer to “PR010 param-
eter: Downstream oxygen sensor voltage”. The displayed value, expressed in mV, is representing
the voltage supplied towards UCE injection by the oxygen sensor placed after the catalyst. This
sensor has the purpose to catalyst diagnostic and to perform a second checking, more exactly, of
the fuel mixture enriching. This function is becoming active only after a certain time of engine
running at warm and it is not active in the engine idling phase.
When the engine is running in “closed loop” phase and at stabilized speed, voltage must fluctuate
ha ving between the maximal and minimal limits a difference of 600-mV ± 100. At deceleration,
voltage mu st be under 200 mV.
Enriching adjustment
vnx.su