2004 DACIA SOLENZA lock

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 17
Procedures
D. SIMPLE SYNCHRONISED PROCEDURE
This procedure allows the synchronisation of a RF remote control with E.C.U. decoder and
is to be applied in the following situations: -the RF remote control c ode is no longer in the range of the E .C.U. decoder reception,
because of blind consecutive pushing over a 1000 time on the RF remote control button.;
- the replacement of the E .C.U. decoder with a new one;
- the replacement of the RF remote control if the E.C.U. decoder is new (E.C.U. decoder
replacement plus a RF key.);
The following operations will be performed: -take off the contact;
- push and maintain like that for about 5 seconds, the doors locking switch located on the
dashboard ; the doors actuators are performing a closing/opening course;
- during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system indicator, push twice the RF remote control button; the doors actuators are performing a
closing/opening course;
-the procedure of synchronisation is finished; check the doors blocking/ unlocking by
pushing the RF remote control.
OBSERVAT ION:
During those 10 seconds you can visualise by means of the CLIP tester t he state 17G
“PROGRAMMING OR TIR/TRF RESYNCHRONISATION” which must be ACTIVE.
E. SPECIFIC SYNCHRONISED PROCEDURE
This procedure is used for the synchronisation of the second RF key with E.C.U. decoder
and will be performed as follows:
-connect the CLIP tester to the diagnostic socket and the battery (or the lighter socket)
of the vehicle;
- select the vehicle type “B41”;
- select the menu “ COMPUTERS TEST” then “ ANTI STARTING”;
- enter the menu “COMMAND MODE” and select “CONFIGURATION”;
- validate the command “ PROGRAMMI NG THE SECOND TIR / TRF KEY” launching
the command from the blue button situated on the right top of the screen; the doors actuators are
performing a closing/opening course. - during the next 10 seconds, confirmed by the permanent lightening of the anti starting
system, push twice t he RF remote control button; the doors will block and then unlock and the
anti starting indicator will turn off. The second remote control is now synchronised. Check the
blocking/ unlocking by pushing the RF remote control.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 20
Diag nostic
3. FAILURE : DOORS BLOCKING SWITCH
Remove the memorised failure by means of the CLIP tester.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
Check the isolation related to the m ass of the
wir ing between the E.C.U. decoder doors’
locking switch B2 pin pole 1
B5 pin pole 5
Is there a correct isolation?
Repair the electric wiring.No
Replace t he doors’ locking switch.
Ye s
RECOMMENDATION Check if the switch does not remain permanently pressed due to a
mechanical blocking.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 23
Diag nostic
6. STATE 11G: ACTIVATE THE RF REMOTE CONTROL/ RECEIVED RF SIGNAL
IN DICATION
If the 17D state is PASSIVE, do not apply the next diagnostic
because the E .C.U. decoder is unused (new).
RECOMMENDATION Perform first the remote control synchronisation.
Do not access the next diagnostic if the state 11G remains
PA SSIVE when activating the RF remote c ontrol at the blocking
and unlocking of the doors.
Check the blocking and unlocking of the doors using the second RF remote control. If this
is one is operating, then the battery of the first RF remote control must be replaced.
Check the presence of +12 V(+DC) at the pin1 of the anti starting bushing.
Is there +12V ?
Pe rform using the CLIP tester, the impulse de tection test at the pin 1 of the anti
starting bushing, when using the RF remote control.
Are any impulses when using the remote control ?
YES Replace the E .C.U. decoder.
NO Replace the anti starting bushing.YES
Check the isolation related to the mass of the electric wiring between:
E.C.U. decoder Pin B1 pol e 1 anti start ing bushi ng Pin B2 pole 1 door locking switch
Pin B5 pole 5
Isolation against mass is good?
YES Fix the electric wiring.
NO Replace the E.C.U. decoder
.
NO
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 24
Diag nostic
7. 11D STATE: OPERATE THE RF REMOTE CONTROL / GOOD RF SIGNAL
INDICATION
Do not access the following diagnostic unless the state 11D
RECOMMENDATION becomes ACTIVE when operating the RF remote control.
Check if the keys belong to the vehicle in question.
There is a desynchronising between the code of the RF remote control and the E.C.U. decoder
if at the activation of the remote control, the 111D state remains PASSIVE a nd the state 11G
becomes ACTIVE for 3 seconds, then becomes PASSIVE. The blocking / unlocking of the
doors is not possible in this case.
Apply the corresponding procedure of resynchronisation (for one or 2 keys).
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 25
Diag nostic
8.14G STATE : DOORS BLOCKING/ UNLOCKING
RECOMMENDATION The state 10G (anti starting) must be ACTIVE .
Check the continuity and the isolation related to the +12 V and to the mass of the electric
wiring on the line E.C.U. decoder
Pin B2 pole 1 door locking switch.
Pin B5 pole 5
Fix the electric wiring if necessary or replace the switch.
If the incident persists, replace the E.C.U. decoder.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 29
Diag nostic
ALP3. THE ANTI STARTING INDICATOR REMAINS PERMANENTLY LIGHTED
( even when the contact is taken off) OR IT REMAINS PERMANENTLY SWITCHED
OFF
RECOMMENDATION Check if the “Procedure E.C.U. decoder replacement” was correctly performed
Check the fuse F03 condition from the cockpit
fuse box.
Is the fuse good?
Is there the failure “DOORS BLOCKING
CONTACT”.
Check the continuity and the isolation related
to the mass, between the pin A 5 of the E.C.U.
decoder and the dashboard.(pin 6 from black
connector)
Is the wiring good?
Replace the fuse.
Analyse this failure and replace.
Fix the wiring.
Perform the following tests in order to find the
damaged element:
- if the anti starting indicator is permanently
lighted, disconnect the connector of the E.C.U.
decoder a nd check if t he indicator switches
off;
- if the anti starting system is turned off, connect
the pin A5 of t he wiring connector from the
E.C.U. decoder to an electric mass and check
if the indicator turns on.
Are the answers affirmatives?
Replace the instrument panel.
Replace the E .C.U. decoder.
Perform a conformity checking.
AFTER REPAIRING Check the operation of the anti starting system.
Remove by means of the CLIP tester the possible m emorised
failures.
No
No
No
Yes
Y e s
No
Yes
Yes
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 32
Diag nostic
ALP6. BLOCKING/UNLOCKING DOORS NOT OPERATING
RECOMMENDATION Check with the CLIP tester the absence of the failures.
If there are memorised failures, these must be removed.
Are the doors blocking mechanisms correctly
operating ?Repair the damaged mechanisms.No
Check the continuity and the isolation related to the
mass of the wiring between :
E.C.U . decoder pin B8 actuators
Pin B9 doors
Is the wiring in good condition?
Fix the wiring.No
Check the continuity and the isolation
related to the mass of the wiring between
E.C.U . pin B2 1 switch
decoder Pin B5 5 blocking doors
Is the wiring in good condition?
Repair.
Di sconnect the E.C.U. decoder, then supply
the wiring c onnector with +12 V at pin B9
and the mass at the pi n B8, than versa (+ 12
V at pin B8 and t he mass at pi n B9).
Ar e the actuators bl ocking/unlocking the
doors?
Damaged actuators.
Replace them.
Replace the E.C.U. decoder, t hen perform the “E.C.U. decoder
replacement procedure”. No
Yes
Yes
No
YesYes
AFTER REPAIRING Perform a conformity
checking.
Check the operation of the anti starting system.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 33
Diag nostic
ALP7. UNLOCKING DOORS NOT OPERATING BY RF REMOTE CONTROL
RECOMMENDATION Check the absence of failures with the CLIP tester.
If there are memorised failures, these must be repaired.
Are the states 11G and 11D be c om ing
A CTIVE when t he RF remote c ontrol is
activated?S ee the treatment of the states 11G
and 11D cf. chapter “Diagnostic”.No
Check the fuse F03 condition from the cockpit
fuse box.
Is it good?
Replace the fuse.No
Ye s
Yes
See the treatment of the failure
“Doors blocking contact” and the state 14 G cf. chapter
“Diagnostic”.
See ALP6.
Yes
No
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system.
Activate the doors’ locking switch from the
dashboard.
Are the doors blocking/ unlocking ?
vnx.su