2004 CHRYSLER VOYAGER manual transmission

ACCUMULATOR
DESCRIPTION
The 4XTE underdrive, overdrive, low/reverse, and 2/4
clutch hydraulic circuits each contain an accumulator.
An accumulator typically consists of a piston, return
spring(s), and a cover or plug. The overdrive and under-
drive accumulators are located within the transaxle
case, and are retained by the valve body (Fig. 145).
The low reverse accumulator (Fig. 146) is also
located within the transaxle case, but the assembly is
retained by a cover and a snap-ring.
The 2/4 accumulator is located in the valve body. It is
retained by a cover and retaining screws (Fig. 147).
VALVE BODY
REMOVAL
NOTE: If valve body is replaced or reconditioned,
the TCM Quick Learn Procedure must be per-
formed. (Refer t o 8 - ELECTRICAL/ELECTRONIC
CONTROL MODULES/TRANSMISSION CONTROL
MODULE - STANDARD PROCEDURE)
(1) Disconnect battery negative cable.
(2) Disconnect gearshift cable from manual valve
lever. (3) Remove manual valve lever from manual shaft.
(4) Raise vehicle on hoist.
(5) Remove oil pan bolts (Fig. 148).
Fig. 145 Underdrive and Overdrive Accumulators
1 - OVERDRIVE PISTON AND SPRING
2 - UNDERDRIVE PISTON AND SPRING
Fig. 146 Low/Reverse Accumulator
1 - PISTON
2 - RETURN SPRINGS
Fig. 147 2/4 Accumulator Assembly
1 - VALVE BODY
2 - RETAINER PLATE
3 - DETENT SPRING
4 - RETURN SPRINGS
5 - PISTON
Fig. 148 Oil Pan Bolts
1 - OIL PAN BOLTS (USE RTV UNDER BOLT HEADS)
21s - 206 41TE AUTOMATIC TRANSAXLERS

CAUTION: The valve body manual shaft pilot may
distort and bind the manual valve if the valve body
is mishandled or dropped.
DISASSEMBLY
NOTE: If valve body assembly is being recondi-
tioned, the PCM/TCM Quick Learn Procedure must
be performed. (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/TRANSMISSION
CONTROL MODULE - STANDARD PROCEDURE)
(1) Remove manual shaft seal (Fig. 154). (2) Remove Transmission Range Sensor retaining
screw (Fig. 155).
(3) Remove Manual Shaft/Rooster Comb and
Transmission Range Sensor (Fig. 156).
Fig. 153 Valve Body Removal/Installation
1 - VALVE BODY
Fig. 154 Manual Shaft Seal
1 - SEAL
2 - MANUAL SHAFT
Fig. 155 Remove Transmission Range Sensor
1 - TRANSMISSION RANGE SENSOR
2 - MANUAL VALVE CONTROL PIN
3 - RETAINING SCREW
Fig. 156 Manual Shaft/Rooster Comb and Transmission Range Sensor
1 - TRANSMISSION RANGE SENSOR
2 - MANUAL SHAFT
3 - ROOSTER COMB
21s - 208 41TE AUTOMATIC TRANSAXLERS
VALVE BODY (Continued)

(14) Install Manual Shaft/Rooster Comb and
Transmission Range Sensor (Fig. 182).
(15) Make sure Manual Valve control pin is con-
tained within the rooster comb slot (Fig. 183). Install
Transmission Range Sensor retaining screw (Fig.
183) and torque to 5 N´m (45 in. lbs.). (16) Install manual shaft seal (Fig. 184).
INSTALLATION
NOTE: If valve body assembly is being replaced or
reconditioned, it is necessary to perform the TCM
Quick Learn Procedure. (Refer t
o 8 - ELECTRICAL/
ELECTRONIC CONTROL MODULES/TRANSMISSION
CONTROL MODULE - STANDARD PROCEDURE)
(1) Install valve body assembly to transaxle (Fig.
185). Install and torque valve body-to-transaxle case
bolts (Fig. 186) to 12 N´m (105 in. lbs.).
Fig. 182 Install Manual Shaft/Rooster Comb and Transmission Range Sensor
1 - TRANSMISSION RANGE SENSOR
2 - MANUAL SHAFT
3 - ROOSTER COMB
Fig. 183 Install Transmission Range Sensor Retaining Screw
1 - TRANSMISSION RANGE SENSOR
2 - MANUAL VALVE CONTROL PIN
3 - RETAINING SCREW
Fig. 184 Manual Shaft Seal
1 - SEAL
2 - MANUAL SHAFT
Fig. 185 Valve Body Removal/Installation
1 - VALVE BODY
RS 41TE AUTOMATIC TRANSAXLE21s - 217
VALVE BODY (Continued)

(2) Install transaxle oil filter (Fig. 187). Inspect
the o-ring and replace if necessary.
(3) Ensure the transaxle oil pan and transaxle
case sealing surfaces are clean and dry. Install an
1/8º bead of Mopar tSilicone Rubber Adhesive Seal-
ant to the oil pan and install (Fig. 188). Torque oil
pan-to-transaxle case bolts (Fig. 189) to 19 N´m (165
in. lbs.). (4) Lower vehicle.
(5) Connect transmission range sensor connector.
(6) Install manual valve lever to manual shaft.
(7) Install gearshift cable to manual valve lever.
(8) Connect battery negative cable.
(9) Fill transaxle with Mopar
tATF +4 Transmis-
sion fluid. (Refer to 21 - TRANSMISSION/TRANS-
AXLE/AUTOMATIC - 41TE/FLUID - STANDARD
PROCEDURE)
Fig. 186 Valve Body Attaching Bolts
1 - VALVE BODY ATTACHING BOLTS (18)
2 - VALVE BODY
Fig. 187 Filter and O-Ring
1 - OIL FILTER
2 - O-RING
Fig. 188 Oil Pan
1 - OIL PAN
2 - 1/8 INCH BEAD OF RTV SEALANT
3 - OIL FILTER
Fig. 189 Oil Pan Bolts
1 - OIL PAN BOLTS (USE RTV UNDER BOLT HEADS)
21s - 218 41TE AUTOMATIC TRANSAXLERS
VALVE BODY (Continued)

COMPRESSOR CLUTCH COIL -
DIAGNOSIS AND TESTING, A/C..........24-15
COMPRESSOR CLUTCH RELAY -
DESCRIPTION, A/C...................24-19
COMPRESSOR CLUTCH RELAY -
INSTALLATION, A/C...................24-20
COMPRESSOR CLUTCH RELAY -
OPERATION, A/C.....................24-19
COMPRESSOR CLUTCH RELAY -
REMOVAL, A/C......................24-20
COMPRESSOR CLUTCH/COIL -
DESCRIPTION, A/C...................24-15
COMPRESSOR CLUTCH/COIL -
INSPECTION, A/C.....................24-17
COMPRESSOR CLUTCH/COIL -
INSTALLATION, A/C...................24-17
COMPRESSOR CLUTCH/COIL -
OPERATION, A/C.....................24-15
COMPRESSOR CLUTCH/COIL -
REMOVAL, A/C......................24-16
COMPRESSOR MOUNTING BRACKET -
2.4L ENGINE - INSTALLATION, A/C.......24-76
COMPRESSOR MOUNTING BRACKET -
2.4L ENGINE - REMOVAL, A/C..........24-75
COMPRESSOR NOISE DIAGNOSIS -
DIAGNOSIS AND TESTING.............24-74
COMPUTER - DESCRIPTION, COMPASS/
MINI-TRIP..........................8M-9
COMPUTER - DIAGNOSIS AND TESTING,
COMPASS MINI-TRIP.................8M-10
COMPUTER - INSTALLATION, COMPASS/
MINI-TRIP.........................8M-10
COMPUTER - OPERATION, COMPASS/
MINI-TRIP............................8M-9
COMPUTER - REMOVAL, COMPASS/
MINI-TRIP.........................8M-10
CONCENTRATION TESTING - DIAGNOSIS
AND TESTING, COOLANT...............7-19
CONDENSER - DESCRIPTION, A/C.......24-76
CONDENSER - INSTALLATION, A/C.......24-78
CONDENSER - OPERATION, A/C.........24-76
CONDENSER - REMOVAL, A/C..........24-77
CONDITION CHECK, STANDARD
PROCEDURE - FLUID LEVEL....21-201,21s-102
CONDITIONER - DESCRIPTION, HEATER
AND AIR ............................24-1
CONDITIONER - OPERATION, HEATER
AND AIR ............................24-4
CONNECTING ROD - DESCRIPTION,
PISTON........................9-116,9-42
CONNECTING ROD - INSTALLATION,
PISTON.............................9-44
CONNECTING ROD - REMOVAL, PISTON . . . 9-43
CONNECTING ROD BEARING
CLEARANCE - STANDARD
PROCEDURE, MEASURING.............9-120
CONNECTING ROD, FITTING.............9-45
CONNECTING RODS - STANDARD
PROCEDURE, FITTING.................9-116
CONNECTOR - DESCRIPTION, DATA LINK . . 8E-6
CONNECTOR - INSTALLATION.......8W-01-11
CONNECTOR - OPERATION, DATA LINK....8E-7
CONNECTOR - REMOVAL...........8W-01-11
CONNECTOR, GROUND AND SPLICE
INFORMATION - DESCRIPTION........8W-01-7
CONNECTOR/GROUND/SPLICE LOCATION
- DESCRIPTION....................8W-91-1
CONSOLE - DESCRIPTION, OVERHEAD....8M-1
CONSOLE - DIAGNOSIS AND TESTING,
OVERHEAD..........................8M-2
CONSOLE - INSTALLATION, LOWER......23-69
CONSOLE - OPERATION, OVERHEAD......8M-2
CONSOLE - REMOVAL, LOWER..........23-69
CONSOLE - REMOVAL, OVERHEAD.......8M-6
CONSOLE LAMP - INSTALLATION,
CENTER............................8L-21
CONSOLE LAMP - REMOVAL, CENTER....8L-21
CONSOLE LAMP SWITCH -
INSTALLATION, CENTER...............8L-21
CONSOLE LAMP SWITCH - REMOVAL,
CENTER............................8L-21
CONSOLE, SPECIAL TOOLS - OVERHEAD
. . 8M-6
CONSOLE TRAY - BRACKET ASSEMBLY -
INSTALLATION, FLOOR
................23-83
CONSOLE TRAY - BRACKET ASSEMBLY -
REMOVAL, FLOOR
....................23-83
CONSOLE TRAY - INSTALLATION, FLOOR
. . 23-83
CONSOLE TRAY - REMOVAL, FLOOR
.....23-83CONTAINER - DESCRIPTION, COOLANT
RECOVERY..........................7-19
CONTAINER - INSTALLATION, COOLANT
RECOVERY..........................7-20
CONTAINER - OPERATION, COOLANT
RECOVERY..........................7-19
CONTAINER - REMOVAL, COOLANT
RECOVERY..........................7-20
CONTAMINATION - DIAGNOSIS AND
TESTING, BRAKE FLUID...........5-32,5s-31
CONTINUITY - STANDARD PROCEDURE,
TESTING.........................8W-01-9
CONTROL (4 SPEED EATX ONLY) -
OPERATION, INTERACTIVE SPEED........8P-2
CONTROL ARM - DESCRIPTION, LOWER . . . 2-12
CONTROL ARM - INSPECTION, LOWER....2-14
CONTROL ARM - INSTALLATION, LOWER . . 2-16
CONTROL ARM - OPERATION, LOWER.....2-12
CONTROL ARM - REMOVAL, LOWER......2-12
CONTROL ARM (REAR BUSHING -
HYDRO) - ASSEMBLY, LOWER...........2-14
CONTROL ARM (REAR BUSHING -
HYDRO) - DISASSEMBLY, LOWER........2-14
CONTROL ARM (REAR BUSHING -
STANDARD) - ASSEMBLY, LOWER........2-14
CONTROL ARM (REAR BUSHING -
STANDARD) - DISASSEMBLY, LOWER.....2-13
CONTROL (ATC) - INSTALLATION,
AUTOMATIC TEMPERATURE............24-29
CONTROL (ATC) - REMOVAL,
AUTOMATIC TEMPERATURE............24-28
CONTROL CABLE - INSTALLATION,
THROTTLE..........................14-36
CONTROL CABLE - REMOVAL,
THROTTLE..........................14-35
CONTROL CALIBRATION - STANDARD
PROCEDURE, A/C-HEATER.............24-20
CONTROL CIRCUIT TEST - DIAGNOSIS
AND TESTING..................8F-30,8F-32
CONTROL INFORMATION LABEL -
DESCRIPTION, VEHICLE EMISSION.......25-1
CONTROL MODULE - DESCRIPTION,
BODY...............................8s-1
CONTROL MODULE - DESCRIPTION,
BODY...............................8E-3
CONTROL MODULE - DESCRIPTION,
FRONT..............................8E-7
CONTROL MODULE - DESCRIPTION,
POWER LIFTGATE....................8E-10
CONTROL MODULE - DESCRIPTION,
SLIDING DOOR......................8E-19
CONTROL MODULE - DESCRIPTION,
TRANSMISSION......................8E-20
CONTROL MODULE - DIAGNOSIS AND
TESTING, FRONT......................8E-7
CONTROL MODULE - INSTALLATION,
BODY...............................8s-3
CONTROL MODULE - INSTALLATION,
BODY...............................8E-5
CONTROL MODULE - INSTALLATION,
FRONT..............................8E-8
CONTROL MODULE - INSTALLATION,
POWER LIFTGATE....................8E-11
CONTROL MODULE - INSTALLATION,
SLIDING DOOR......................8E-20
CONTROL MODULE - OPERATION, BODY . . . 8s-1
CONTROL MODULE - OPERATION, BODY . . . 8E-3
CONTROL MODULE - OPERATION,
FRONT..............................8E-7
CONTROL MODULE - OPERATION,
POWER LIFTGATE....................8E-11
CONTROL MODULE - OPERATION,
SLIDING DOOR......................8E-19
CONTROL MODULE - OPERATION,
TRANSMISSION......................8E-20
CONTROL MODULE - REMOVAL, BODY....8s-3
CONTROL MODULE - REMOVAL, BODY....8E-4
CONTROL MODULE - REMOVAL, FRONT . . . 8E-8
CONTROL MODULE - REMOVAL, POWER
LIFTGATE
...........................8E-11
CONTROL MODULE - REMOVAL,
SLIDING DOOR
......................8E-19
CONTROL MOTOR - DESCRIPTION, IDLE
AIR
...............................14-28
CONTROL MOTOR - INSTALLATION, IDLE
AIR
...............................14-29
CONTROL MOTOR - OPERATION, IDLE
AIR
...............................14-28CONTROL MOTOR - REMOVAL, IDLE AIR . . 14-29
CONTROL (MTC) - INSTALLATION,
MANUAL TEMPERATURE...............24-29
CONTROL (MTC) - REMOVAL, MANUAL
TEMPERATURE......................24-29
CONTROL RELAY - DESCRIPTION,
TRANSMISSION..............21-247,21s-150
CONTROL RELAY - OPERATION,
TRANSMISSION..............21-248,21s-150
CONTROL SWITCH - DIAGNOSIS AND
TESTING, TRACTION...................5-82
CONTROL SYSTEM - DESCRIPTION,
TRACTION...........................5-76
CONTROL SYSTEM - OPERATION,
AUTOMATIC TEMPERATURE...........24-112
CONTROL SYSTEM - OPERATION,
EVAPORATION.......................25-10
CONTROL SYSTEM - OPERATION,
MANUAL TEMPERATURE..............24-112
CONTROL SYSTEM - OPERATION,
TRACTION...........................5-77
CONTROLLER - DESCRIPTION,
OCCUPANT RESTRAINT................8O-8
CONTROLLER - INSTALLATION,
OCCUPANT RESTRAINT................8O-8
CONTROLLER - INSTALLATION, SBEC....8E-17
CONTROLLER - OPERATION, 8-VOLT
SUPPLY - PCM OUTPUT - SBEC.........8E-15
CONTROLLER - OPERATION, OCCUPANT
RESTRAINT..........................8O-8
CONTROLLER - REMOVAL, NGC.........8E-17
CONTROLLER - REMOVAL, OCCUPANT
RESTRAINT...........................8O-8
CONTROLLER - REMOVAL, SBEC........8E-16
CONTROLLER ANTILOCK BRAKE -
DESCRIPTION........................8E-5
CONTROLLER ANTILOCK BRAKE -
INSTALLATION........................8E-6
CONTROLLER ANTILOCK BRAKE -
OPERATION..........................8E-5
CONTROLLER ANTILOCK BRAKE -
REMOVAL...........................8E-6
CONVENTIONAL BATTERY CHARGING -
STANDARD PROCEDURE...............8F-11
CONVERTER - DESCRIPTION, CATALYTIC . . . 11-4
CONVERTER - DESCRIPTION, TORQUE . . 21-242,
21s-144
CONVERTER - INSPECTION, CATALYTIC....11-5
CONVERTER - INSTALLATION, CATALYTIC . . 11-6
CONVERTER - INSTALLATION, TORQUE . . 21-247,
21s-149
CONVERTER - OPERATION, CATALYTIC....11-4
CONVERTER - OPERATION, TORQUE....21-245,
21s-148
CONVERTER - REMOVAL, CATALYTIC......11-5
CONVERTER - REMOVAL, TORQUE.....21-247,
21s-149
CONVERTER HOUSING FLUID LEAKAGE -
DIAGNOSIS AND TESTING, TORQUE....21-123,
21s-31
COOL DOWN TEST - DIAGNOSIS AND
TESTING, A/C........................24-6
COOLANT - DESCRIPTION, ENGINE.......7-19
COOLANT - DESCRIPTION, ENGINE........0-3
COOLANT - STANDARD PROCEDURE,
ADDING ADDITIONAL...................7-5
COOLANT CONCENTRATION TESTING -
DIAGNOSIS AND TESTING..............7-19
COOLANT LEVEL CHECK - STANDARD
PROCEDURE..........................7-5
COOLANT RECOVERY CONTAINER -
DESCRIPTION........................7-19
COOLANT RECOVERY CONTAINER -
INSTALLATION........................7-20
COOLANT RECOVERY CONTAINER -
OPERATION..........................7-19
COOLANT RECOVERY CONTAINER -
REMOVAL...........................7-20
COOLANT RECOVERY SYSTEM -
DIAGNOSIS AND TESTING
..............7-20
COOLANT SERVICE - STANDARD
PROCEDURE
.........................7-19
COOLANT TEMPERATURE SENSOR -
2.4L - DESCRIPTION, ENGINE
............7-21
COOLANT TEMPERATURE SENSOR -
2.4L - INSTALLATION, ENGINE
...........7-21
COOLANT TEMPERATURE SENSOR -
2.4L - REMOVAL, ENGINE
...............7-21
8 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

RECOVERY CONTAINER - DESCRIPTION,
COOLANT............................7-19
RECOVERY CONTAINER - INSTALLATION,
COOLANT............................7-20
RECOVERY CONTAINER - OPERATION,
COOLANT............................7-19
RECOVERY CONTAINER - REMOVAL,
COOLANT............................7-20
RECOVERY SYSTEM - DIAGNOSIS AND
TESTING, COOLANT...................7-20
REFACING VALVES AND VALVE SEATS -
STANDARD PROCEDURE..........9-104,9s-21
REFERENCES - DESCRIPTION, TORQUE . . Intro.-8
REFRIGERANT - DESCRIPTION..........24-92
REFRIGERANT - OPERATION............24-92
REFRIGERANT LINE - DESCRIPTION......24-65
REFRIGERANT LINES - INSTALLATION,
UNDERBODY.......................24-111
REFRIGERANT LINES - OPERATION......24-65
REFRIGERANT LINES - REMOVAL,
UNDERBODY.......................24-110
REFRIGERANT OIL - DESCRIPTION......24-92
REFRIGERANT OIL - OPERATION........24-92
REFRIGERANT OIL LEVEL - STANDARD
PROCEDURE........................24-93
REFRIGERANT RECOVERY - STANDARD
PROCEDURE........................24-71
REFRIGERANT SYSTEM CHARGE -
STANDARD PROCEDURE...............24-72
REFRIGERANT SYSTEM EVACUATE -
STANDARD PROCEDURE...............24-72
REFRIGERANT SYSTEM LEAKS -
DIAGNOSIS AND TESTING.............24-66
REFRIGERANT SYSTEM SERVICE
EQUIPMENT - STANDARD PROCEDURE . . . 24-70
REGULATOR - DESCRIPTION, VOLTAGE . . . 8F-27,
8F-29
REGULATOR - INSTALLATION, FUEL
PRESSURE..........................14-7
REGULATOR - MANUAL - INSTALLATION,
WINDOW...........................23-23
REGULATOR - MANUAL - REMOVAL,
WINDOW...........................23-22
REGULATOR - OPERATION, FUEL
PRESSURE..........................14-7
REGULATOR - OPERATION, VOLTAGE....8F-27,
8F-29
REGULATOR - POWER - INSTALLATION,
WINDOW...........................23-22
REGULATOR - POWER - REMOVAL,
WINDOW...........................23-22
REGULATOR - REMOVAL, FUEL
PRESSURE..........................14-7
REINFORCEMENT - INSTALLATION,
FRONT BUMPER......................13-2
REINFORCEMENT - INSTALLATION,
GRILLE OPENING....................23-54
REINFORCEMENT - INSTALLATION, REAR
BUMPER............................13-3
REINFORCEMENT - REMOVAL, FRONT
BUMPER............................13-2
REINFORCEMENT - REMOVAL, GRILLE
OPENING...........................23-54
REINFORCEMENT - REMOVAL, REAR
BUMPER............................13-3
RELAY - DESCRIPTION, A/C
COMPRESSOR CLUTCH
...............24-19
RELAY - DESCRIPTION, AUTO SHUT
DOWN
..............................8I-3
RELAY - DESCRIPTION, BLOWER
MOTOR
.......................24-24,24-37
RELAY - DESCRIPTION, FUEL PUMP
.....14-28
RELAY - DESCRIPTION, RADIATOR FAN
....7-30
RELAY - DESCRIPTION, REAR WINDOW
DEFOGGER
..........................8G-3
RELAY - DESCRIPTION, TRANSMISSION
CONTROL
...................21-247,21s-150
RELAY - INSTALLATION, A/C
COMPRESSOR CLUTCH
...............24-20
RELAY - INSTALLATION, BLOWER
MOTOR
.......................24-25,24-38
RELAY - INSTALLATION, RADIATOR FAN
. . . 7-30
RELAY - INSTALLATION, REAR WINDOW
DEFOGGER
..........................8G-3
RELAY - OPERATION, A/C COMPRESSOR
CLUTCH
............................24-19
RELAY - OPERATION, AUTO SHUT DOWN
. . . 8I-3RELAY - OPERATION, BLOWER MOTOR . . 24-24,
24-37
RELAY - OPERATION, FUEL PUMP.......14-28
RELAY - OPERATION, RADIATOR FAN......7-30
RELAY - OPERATION, REAR WINDOW
DEFOGGER..........................8G-3
RELAY - OPERATION, TRANSMISSION
CONTROL...................21-248,21s-150
RELAY - REMOVAL, A/C COMPRESSOR
CLUTCH............................24-20
RELAY - REMOVAL, BLOWER MOTOR....24-25,
24-38
RELAY - REMOVAL, RADIATOR FAN.......7-30
RELAY - REMOVAL, REAR WINDOW
DEFOGGER..........................8G-3
RELEASE - STANDARD PROCEDURE,
PARKING BRAKE AUTOMATIC
ADJUSTER TENSION..............5-58,5s-61
RELEASE CABLE - INSTALLATION, LATCH . 23-62
RELEASE CABLE - REMOVAL, LATCH.....23-61
RELEASE LEVER AND BEARING -
INSTALLATION, CLUTCH.................6-7
RELEASE LEVER AND BEARING -
REMOVAL, CLUTCH.....................6-6
RELEASE PROCEDURE - STANDARD
PROCEDURE, FUEL SYSTEM
PRESSURE..........................14-2
RELIEF VALVE - DESCRIPTION, HIGH
PRESSURE.........................24-73
RELIEF VALVE - INSTALLATION, OIL
PRESSURE.........................9-141
RELIEF VALVE - OPERATION, HIGH
PRESSURE...........................24-73
RELIEF VALVE - REMOVAL, OIL
PRESSURE.........................9-141
REMOTE ENTRY MODULE -
DESCRIPTION, SENTRY KEY.............8Q-3
REMOTE ENTRY MODULE - DIAGNOSIS
AND TESTING, SENTRY KEY.............8Q-5
REMOTE ENTRY MODULE -
INSTALLATION, SENTRY KEY............8Q-6
REMOTE ENTRY MODULE - OPERATION,
SENTRY KEY.........................8Q-4
REMOTE ENTRY MODULE - REMOVAL,
SENTRY KEY.........................8Q-5
REMOTE ENTRY SYSTEM - DIAGNOSIS
AND TESTING, SENTRY KEY.............8Q-3
REMOTE KEYLESS ENTRY MODULE -
DESCRIPTION.......................8N-43
REMOTE KEYLESS ENTRY MODULE -
DIAGNOSIS AND TESTING.............8N-43
REMOTE KEYLESS ENTRY MODULE -
INSTALLATION......................8N-44
REMOTE KEYLESS ENTRY MODULE -
OPERATION.........................8N-43
REMOTE KEYLESS ENTRY MODULE -
REMOVAL..........................8N-44
REMOTE KEYLESS ENTRY
TRANSMITTER PROGRAMMING -
STANDARD PROCEDURE...............8N-5
REMOTE SWITCH - DIAGNOSIS AND
TESTING...........................8N-49
REMOTE SWITCH - INSTALLATION......8N-49
REMOTE SWITCH - REMOVAL..........8N-49
REMOTE SWITCHES - DESCRIPTION.....8A-12
REMOTE SWITCHES - DIAGNOSIS AND
TESTING...........................8A-12
REMOTE SWITCHES - INSTALLATION.....8A-14
REMOTE SWITCHES - OPERATION.......8A-12
REMOTE SWITCHES - REMOVAL........8A-13
REPAIR - DESCRIPTION, FRONT CRADLE
CROSSMEMBER THREAD...............13-9
REPAIR - DESCRIPTION, THREADED
HOLE.............................Intro.-5
REPAIR - STANDARD PROCEDURE, GRID
LINE AND TERMINAL..................8G-4
REPAIR - STANDARD PROCEDURE,
INTAKE MANIFOLD VACUUM PORT......9-145
REPAIR - STANDARD PROCEDURE,
MANIFOLD STRIPPED THREAD
..........9-145
REPAIR - STANDARD PROCEDURE,
PLASTIC BODY PANEL
.................23-3
REPAIR OF DAMAGED OR WORN
THREADS - STANDARD PROCEDURE
. . 9-10,9-86
REPAIRING - STANDARD PROCEDURE,
TIRE LEAK
.....................22-17,22s-9
REQUIREMENTS - DESCRIPTION,
ENGINE COOLING SYSTEM
..............24-1REQUIREMENTS - DESCRIPTION, FUEL.....0-4
REQUIREMENTS - DIESEL ENGINE -
DESCRIPTION, FUEL....................0-6
RESERVOIR - DESCRIPTION, VACUUM....8P-6
RESERVOIR - INSTALLATION, VACUUM....8P-6
RESERVOIR - INSTALLATION, WASHER . . . 8R-13
RESERVOIR - OPERATION, VACUUM......8P-6
RESERVOIR - REMOVAL, VACUUM........8P-6
RESERVOIR - REMOVAL, WASHER......8R-13
RESET - STANDARD PROCEDURE,
PARKING BRAKE AUTOMATIC
ADJUSTER TENSION..............5-59,5s-61
RESISTANCE, SPECIFICATIONS - SPARK
PLUG CABLE.........................8I-2
RESISTANCE TEST - DIAGNOSIS AND
TESTING, FEED CIRCUIT..........8F-32,8F-34
RESISTOR - DESCRIPTION, BLOWER
MOTOR............................24-38
RESISTOR - INSTALLATION, BLOWER
MOTOR............................24-39
RESISTOR - OPERATION, BLOWER
MOTOR............................24-38
RESISTOR - REMOVAL, BLOWER
MOTOR............................24-39
RESISTOR BLOCK - DESCRIPTION,
BLOWER MOTOR....................24-26
RESISTOR BLOCK - DIAGNOSIS AND
TESTING, BLOWER MOTOR............24-26
RESISTOR BLOCK - DIAGNOSIS AND
TESTING, REAR BLOWER MOTOR.......24-38
RESISTOR BLOCK - INSTALLATION,
BLOWER MOTOR......................24-27
RESISTOR BLOCK - OPERATION,
BLOWER MOTOR....................24-26
RESISTOR BLOCK - REMOVAL, BLOWER
MOTOR............................24-26
RESONATOR - INSTALLATION............11-9
RESONATOR - REMOVAL...............11-9
RESTRAINT ANCHOR - DESCRIPTION,
CHILD..............................8O-4
RESTRAINT ANCHOR - OPERATION,
CHILD..............................8O-4
RESTRAINT CONTROLLER -
DESCRIPTION, OCCUPANT..............8O-8
RESTRAINT CONTROLLER -
INSTALLATION, OCCUPANT.............8O-8
RESTRAINT CONTROLLER - OPERATION,
OCCUPANT..........................8O-8
RESTRAINT CONTROLLER - REMOVAL,
OCCUPANT..........................8O-8
RESTRAINTS - DESCRIPTION............8O-2
RESTRAINTS - OPERATION.............8O-2
RESTRAINTS - WARNING...............8O-2
RESTRICTION CHECK - DIAGNOSIS AND
TESTING, EXHAUST SYSTEM............11-2
RETAINER - INSTALLATION,
CRANKSHAFT REAR OIL SEAL..........9-129
RETAINER - INSTALLATION, PLASTIC
GROCERY BAG
.....................23-105
RETAINER - REMOVAL, CRANKSHAFT
REAR OIL SEAL
......................9-129
RETAINER - REMOVAL, PLASTIC
GROCERY BAG
.....................23-104
RETRACTOR - FIRST ROW - OUTBOARD
- INSTALLATION, SEAT BELT
...........8O-14
RETRACTOR - FIRST ROW - OUTBOARD
- REMOVAL, SEAT BELT
...............8O-14
RETRACTOR - OUTBOARD - FRONT -
INSTALLATION, SEAT BELT
.............8O-14
RETRACTOR - OUTBOARD - FRONT -
REMOVAL, SEAT BELT
................8O-14
RETRACTOR - SECOND ROW - LEFT
OUTBOARD - INSTALLATION, SEAT
BELT
..............................8O-17
RETRACTOR - SECOND ROW - LEFT
OUTBOARD - REMOVAL, SEAT BELT
.....8O-17
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD - INSTALLATION, SEAT
BELT
..............................8O-15
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD - REMOVAL, SEAT BELT
.....8O-15
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR HVAC - LWB -
INSTALLATION, SEAT BELT
.............8O-16
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR HVAC - LWB -
REMOVAL, SEAT BELT
................8O-16
28 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

SEAT TRACK MANUAL ADJUSTER -
INSTALLATION, FRONT................23-95
SEAT TRACK MANUAL ADJUSTER -
REMOVAL, FRONT....................23-95
SEAT TRACK POWER ADJUSTER -
INSTALLATION, FRONT................23-95
SEAT TRACK POWER ADJUSTER -
REMOVAL, FRONT....................23-95
SEATBACK ASSIST STRAP -
INSTALLATION, FRONT................23-92
SEATBACK ASSIST STRAP - REMOVAL,
FRONT.............................23-92
SEATBACK COVER - INSTALLATION,
FRONT.............................23-93
SEATBACK COVER - REMOVAL, FRONT . . . 23-93
SEATBACK PANEL - INSTALLATION,
BENCH.............................23-99
SEATBACK PANEL - INSTALLATION,
FRONT.............................23-93
SEATBACK PANEL - REMOVAL, BENCH . . . 23-99
SEATBACK PANEL - REMOVAL, FRONT....23-92
SEAT/MIRROR MODULE - DESCRIPTION,
MEMORY...........................8E-10
SEAT/MIRROR MODULE - DIAGNOSIS
AND TESTING, MEMORY...............8E-10
SEAT/MIRROR MODULE -
INSTALLATION, MEMORY..............8E-10
SEAT/MIRROR MODULE - OPERATION,
MEMORY...........................8E-10
SEAT/MIRROR MODULE - REMOVAL,
MEMORY...........................8E-10
SEATS - CLEANING, INTAKE/EXHAUST
VALVES.....................9-105,9-32,9s-22
SEATS - DESCRIPTION, INTAKE/
EXHAUST VALVES...........9-104,9-32,9s-21
SEATS - INSPECTION, INTAKE/EXHAUST
VALVES .......................9-105,9s-22
SEATS - INSTALLATION, INTAKE/
EXHAUST VALVES...............9-106,9s-23
SEATS - OPERATION, INTAKE/EXHAUST
VALVES .......................9-104,9s-21
SEATS - REMOVAL, INTAKE/EXHAUST
VALVES .......................9-105,9s-22
SEATS - STANDARD PROCEDURE,
REFACING VALVES AND VALVE.....9-104,9s-21
SECOND ROW - INSTALLATION, BENCH
SEAT RISER........................23-101
SECOND ROW - LEFT OUTBOARD -
INSTALLATION, SEAT BELT &
RETRACTOR........................8O-17
SECOND ROW - LEFT OUTBOARD -
REMOVAL, SEAT BELT & RETRACTOR....8O-17
SECOND ROW - REMOVAL, BENCH SEAT
RISER............................23-101
SECOND ROW - RIGHT OUTBOARD -
INSTALLATION, SEAT BELT &
RETRACTOR........................8O-15
SECOND ROW - RIGHT OUTBOARD -
REMOVAL, SEAT BELT & RETRACTOR
....8O-15
SECOND ROW - RIGHT OUTBOARD
WITH REAR HVAC - LWB -
INSTALLATION, SEAT BELT &
RETRACTOR
........................8O-16
SECOND ROW - RIGHT OUTBOARD
WITH REAR HVAC - LWB - REMOVAL,
SEAT BELT & RETRACTOR
.............8O-16
SECOND ROW - THREE PASSENGER
BENCH - INSTALLATION, SEAT BELT
BUCKLE
............................8O-15
SECOND ROW - THREE PASSENGER
BENCH - REMOVAL, SEAT BELT
BUCKLE
............................8O-15
SECOND ROW INBOARD - 50/50 BENCH
- INSTALLATION, SEAT BELT BUCKLE
....8O-13
SECOND ROW INBOARD - 50/50 BENCH
- REMOVAL, SEAT BELT BUCKLE
........8O-13
SECTION IDENTIFICATION AND
INFORMATION - DESCRIPTION
........8W-01-6
SECURITY - DESCRIPTION, VEHICLE
THEFT
..............................8Q-1
SECURITY - OPERATION, VEHICLE THEFT
. . 8Q-1
SECURITY SYSTEM - DIAGNOSIS AND
TESTING, VEHICLE THEFT
..............8Q-3
SELECTION, ADJUSTMENTS - OUTPUT
FLANGE SHIM
........................21-7
SELECTOR - INSTALLATION, GEARSHIFT
CABLE
.............................21-84SELECTOR - REMOVAL, GEARSHIFT
CABLE.............................21-81
SELF-DIAGNOSTICS - DIAGNOSIS AND
TESTING............................8J-2
SENDING UNIT / SENSOR -
DESCRIPTION, FUEL LEVEL.............14-5
SENDING UNIT / SENSOR -
INSTALLATION, FUEL LEVEL.............14-5
SENDING UNIT / SENSOR - OPERATION,
FUEL LEVEL..........................14-5
SENDING UNIT / SENSOR - REMOVAL,
FUEL LEVEL..........................14-5
SENSE - PCM INPUT - OPERATION,
IGNITION...........................8E-15
SENSITIVE DEVICES - STANDARD
PROCEDURE, ELECTROSTATIC
DISCHARGE (ESD).................8W-01-8
SENSOR - 2.4L - DESCRIPTION, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - 2.4L - INSTALLATION, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - 2.4L - REMOVAL, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - 3.3/3.8L - DESCRIPTION,
ENGINE COOLANT TEMPERATURE........7-21
SENSOR - 3.3/3.8L - INSTALLATION,
ENGINE COOLANT TEMPERATURE........7-22
SENSOR - 3.3/3.8L - REMOVAL, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - AWD - INSTALLATION, REAR
WHEEL SPEED........................5-80
SENSOR - AWD - REMOVAL, REAR
WHEEL SPEED........................5-80
SENSOR - DESCRIPTION, AMBIENT
TEMP.............................8M-11
SENSOR - DESCRIPTION, BATTERY
TEMPERATURE......................8F-23
SENSOR - DESCRIPTION, CAMSHAFT
POSITION............................8I-4
SENSOR - DESCRIPTION, CRANKSHAFT
POSITION..........................14-25
SENSOR - DESCRIPTION, ENGINE SPEED . 14-26
SENSOR - DESCRIPTION, EVAPORATOR
TEMPERATURE......................24-27
SENSOR - DESCRIPTION, FUEL LEVEL
SENDING UNIT.......................14-5
SENSOR - DESCRIPTION, HEATED SEAT . . 8G-12
SENSOR - DESCRIPTION, INFRARED
TEMPERATURE......................24-29
SENSOR - DESCRIPTION, INLET AIR
TEMPERATURE......................14-30
SENSOR - DESCRIPTION, KNOCK.........8I-8
SENSOR - DESCRIPTION, MAP..........14-30
SENSOR - DESCRIPTION, O2...........14-32
SENSOR - DESCRIPTION, PINCH........8N-17
SENSOR - DESCRIPTION, THROTTLE
POSITION..........................14-36
SENSOR - DESCRIPTION,
TRANSMISSION RANGE.......21-248,21s-150
SENSOR - DIAGNOSIS AND TESTING,
AMBIENT TEMPERATURE..............8M-12
SENSOR - DIAGNOSIS AND TESTING,
HEATED SEAT .......................8G-12
SENSOR - DIAGNOSIS AND TESTING,
TIRE PRESSURE
................22-10,22s-2
SENSOR - FWD - INSTALLATION, REAR
WHEEL SPEED
........................5-81
SENSOR - FWD - REMOVAL, REAR
WHEEL SPEED
........................5-81
SENSOR - INPUT - DESCRIPTION,
SPEED
.....................21-239,21s-140
SENSOR - INPUT - INSTALLATION,
SPEED
.....................21-240,21s-141
SENSOR - INPUT - OPERATION, SPEED
. 21-240,
21s-140
SENSOR - INPUT - REMOVAL, SPEED
. . . 21-240,
21s-141
SENSOR - INSTALLATION, FRONT
WHEEL SPEED
........................5-80
SENSOR - INSTALLATION, FUEL LEVEL
SENDING UNIT
.......................14-5
SENSOR - INSTALLATION, PINCH
........8N-17
SENSOR - INSTALLATION,
TRANSMISSION RANGE
.......21-249,21s-152
SENSOR - INSTALLATION, VEHICLE
SPEED
............................21-115
SENSOR - OPERATION, AMBIENT TEMP
. . 8M-11SENSOR - OPERATION, BATTERY
TEMPERATURE......................8F-23
SENSOR - OPERATION, CAMSHAFT
POSITION............................8I-4
SENSOR - OPERATION, CRANKSHAFT
POSITION..........................14-25
SENSOR - OPERATION, ENGINE SPEED . . . 14-26
SENSOR - OPERATION, EVAPORATOR
TEMPERATURE......................24-28
SENSOR - OPERATION, FUEL LEVEL
SENDING UNIT.......................14-5
SENSOR - OPERATION, HEATED SEAT....8G-12
SENSOR - OPERATION, INFRARED
TEMPERATURE......................24-29
SENSOR - OPERATION, KNOCK...........8I-8
SENSOR - OPERATION, MAP...........14-30
SENSOR - OPERATION, O2.............14-32
SENSOR - OPERATION, PINCH..........8N-17
SENSOR - OPERATION, THROTTLE
POSITION..........................14-36
SENSOR - OPERATION, TRANSMISSION
RANGE.....................21-248,21s-151
SENSOR - OUTPUT - DESCRIPTION,
SPEED.....................21-241,21s-142
SENSOR - OUTPUT - INSTALLATION,
SPEED.....................21-242,21s-143
SENSOR - OUTPUT - OPERATION,
SPEED.....................21-241,21s-142
SENSOR - OUTPUT - REMOVAL, SPEED . 21-241,
21s-143
SENSOR - REMOVAL, BATTERY
TEMPERATURE........................8F-23
SENSOR - REMOVAL, CRANKSHAFT
POSITION..........................14-25
SENSOR - REMOVAL, FRONT WHEEL
SPEED..............................5-79
SENSOR - REMOVAL, FUEL LEVEL
SENDING UNIT.......................14-5
SENSOR - REMOVAL, PINCH...........8N-17
SENSOR - REMOVAL, TRANSMISSION
RANGE.....................21-249,21s-151
SENSOR - REMOVAL, VEHICLE SPEED . . . 21-115
SENSOR - SPECIFICATIONS, BATTERY
TEMPERATURE......................8F-22
SENSOR - TPM - CAUTION........22-10,22s-2
SENSOR - TPM - DESCRIPTION....22-10,22s-1
SENSOR - TPM - INSTALLATION....22-12,22s-3
SENSOR - TPM - OPERATION......22-10,22s-2
SENSOR - TPM - REMOVAL.......22-11,22s-2
SENSOR AIR GAP, SPECIFICATIONS -
WHEEL SPEED........................5-79
SENSOR CIRCUIT - DIAGNOSIS AND
TESTING, AMBIENT TEMPERATURE......8M-12
SENSOR RETRAIN - STANDARD
PROCEDURE, TIRE PRESSURE.....22-10,22s-2
SENSOR RETURN - PCM INPUT -
OPERATION.........................8E-15
SENTRY KEY IMMOBILIZER MODULE -
DESCRIPTION.......................8E-18
SENTRY KEY IMMOBILIZER MODULE -
INSTALLATION.......................8E-19
SENTRY KEY IMMOBILIZER MODULE -
OPERATION.........................8E-18
SENTRY KEY IMMOBILIZER MODULE -
REMOVAL..........................8E-18
SENTRY KEY REMOTE ENTRY MODULE -
DESCRIPTION
........................8Q-3
SENTRY KEY REMOTE ENTRY MODULE -
DIAGNOSIS AND TESTING
..............8Q-5
SENTRY KEY REMOTE ENTRY MODULE -
INSTALLATION
.......................8Q-6
SENTRY KEY REMOTE ENTRY MODULE -
OPERATION
..........................8Q-4
SENTRY KEY REMOTE ENTRY MODULE -
REMOVAL
...........................8Q-5
SENTRY KEY REMOTE ENTRY SYSTEM -
DIAGNOSIS AND TESTING
..............8Q-3
SERVO - DESCRIPTION
.................8P-4
SERVO - INSTALLATION
................8P-5
SERVO - OPERATION
..................8P-4
SERVO - REMOVAL
....................8P-5
SET SWITCH - DESCRIPTION,
MEMORY
.....................8N-12,8N-55
SET SWITCH - INSTALLATION,
MEMORY
.....................8N-13,8N-56
SET SWITCH - OPERATION,
MEMORY
.....................8N-13,8N-56
RSINDEX31
Description Group-Page Description Group-Page Description Group-Page

TIMING CHAIN COVER - INSTALLATION . . . 9-155
TIMING CHAIN COVER - REMOVAL......9-153
TIMING CHAIN WEAR - STANDARD
PROCEDURE, MEASURING.............9-153
TIMING VERIFICATION - STANDARD
PROCEDURE, VALVE..................9-153
TIRE - DESCRIPTION.............22-13,22s-5
TIRE AND WHEEL ASSEMBLY
(ALUMINUM WHEEL) - INSTALLATION.....22-8
TIRE AND WHEEL ASSEMBLY
(ALUMINUM WHEEL) - REMOVAL........22-7
TIRE AND WHEEL ASSEMBLY (STEEL
WHEEL) - INSTALLATION...............22-8
TIRE AND WHEEL ASSEMBLY (STEEL
WHEEL) - REMOVAL...................22-8
TIRE AND WHEEL BALANCE -
STANDARD PROCEDURE................22-5
TIRE AND WHEEL MATCH MOUNTING -
STANDARD PROCEDURE................22-7
TIRE AND WHEEL ROTATION -
STANDARD PROCEDURE................22-7
TIRE AND WHEEL VIBRATION -
DIAGNOSIS AND TESTING..............22-1
TIRE INFLATION PRESSURES -
STANDARD PROCEDURE..........22-16,22s-8
TIRE LEAK REPAIRING - STANDARD
PROCEDURE...................22-17,22s-9
TIRE NOISE - DIAGNOSIS AND TESTING . . 22-14,
22s-6
TIRE PRESSURE FOR HIGH SPEED
OPERATION - STANDARD PROCEDURE . . . 22-17,
22s-9
TIRE PRESSURE MONITORING -
DESCRIPTION...................22-9,22s-1
TIRE PRESSURE MONITORING -
OPERATION.....................22-9,22s-1
TIRE PRESSURE SENSOR - DIAGNOSIS
AND TESTING..................22-10,22s-2
TIRE PRESSURE SENSOR RETRAIN -
STANDARD PROCEDURE..........22-10,22s-2
TIRE (TEMPORARY) - DESCRIPTION,
SPARE ........................22-14,22s-6
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING..................22-16,22s-8
TIRES - CLEANING.............22-17,22s-10
TIRES - DESCRIPTION, RADIAL-PLY . 22-14,22s-6
TIRES - DESCRIPTION, REPLACEMENT . . . 22-14,
22s-6
TIRE/VEHICLE LEAD - DIAGNOSIS AND
TESTING......................22-14,22s-6
TO CYLINDER BORE FITTING -
STANDARD PROCEDURE, PISTON........9-42
TO FILLER NECK SEAL - DIAGNOSIS
AND TESTING, RADIATOR CAP...........7-27
TO GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT.............8W-01-9
TO GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT . 8W-01-10
TO USE WIRING DIAGRAMS -
DESCRIPTION, HOW................8W-01-1
TONE WHEEL - INSPECTION.............5-82
TONE WHEEL RUNOUT, SPECIFICATIONS . . . 5-79
TOOLS - 2.4L ENGINE, SPECIAL..........9-21
TOOLS - 3.3/3.8L ENGINE, SPECIAL.......9-95
TOOLS - 41TE AUTOMATIC TRANSAXLE,
SPECIAL..........................21-183
TOOLS - BASE BRAKE SYSTEM, SPECIAL . . 5-10,
5s-9
TOOLS - BATTERY SYSTEM SPECIAL
TOOLS, SPECIAL......................8F-7
TOOLS - BODY, SPECIAL...............23-13
TOOLS - COOLING SYSTEM, SPECIAL......7-6
TOOLS - EXHAUST SYSTEM, SPECIAL.....11-4
TOOLS - FRONT SUSPENSION, SPECIAL....2-3
TOOLS - FUEL, SPECIAL...........14-23,14-4
TOOLS - OVERHEAD CONSOLE, SPECIAL . . 8M-6
TOOLS - POWER DISTRIBUTION
SYSTEMS, SPECIAL................8W-97-1
TOOLS - POWER STEERING GEAR,
SPECIAL...........................19-34
TOOLS - POWER STEERING PUMP,
SPECIAL
...........................19-43
TOOLS - POWER STEERING, SPECIAL
.....19-9
TOOLS - REAR SUSPENSION, SPECIAL
....2-28
TOOLS - SDP POWER TRANSFER UNIT,
SPECIAL
............................21-8
TOOLS - WIRING/TERMINAL, SPECIAL
. 8W-01-10TOOLS, DIAGNOSIS AND TESTING -
SPECIAL............................3-34
TOOLS, SCHEMATICS AND DIAGRAMS -
SPECIAL...........................21s-89
TOOLS, SPECIAL TOOLS - BATTERY
SYSTEM SPECIAL.....................8F-7
TOOLS, SPECIFICATIONS - SPECIAL......8F-23
TOOLS, T850 TRANSAXLE - SPECIAL.......6-6
TOOLS, T850 TRANSAXLE - SPECIAL.....21-58
TOP COVER - INSTALLATION,
INSTRUMENT PANEL..................23-69
TOP COVER - REMOVAL, INSTRUMENT
PANEL.............................23-68
TOP PAD ASSEMBLY - INSTALLATION,
INSTRUMENT PANEL..................23-72
TOP PAD ASSEMBLY - REMOVAL,
INSTRUMENT PANEL..................23-71
TORQUES, SPECIFICATIONS.......8F-33,8F-35
TOUCH-UP - DESCRIPTION, PAINTED.....23-85
TOWING - STANDARD PROCEDURE.......0-29
TPM - CAUTION, SENSOR.........22-10,22s-2
TPM - DESCRIPTION, SENSOR.....22-10,22s-1
TPM - INSTALLATION, SENSOR....22-12,22s-3
TPM - OPERATION, SENSOR.......22-10,22s-2
TPM - REMOVAL, SENSOR........22-11,22s-2
TRACK - DESCRIPTION, DRIVER POWER
SEAT.........................8N-15,8N-58
TRACK - DESCRIPTION, PASSENGER
POWER SEAT..................8N-16,8N-59
TRACK - DIAGNOSIS AND TESTING,
DRIVER POWER SEAT...........8N-15,8N-58
TRACK - DIAGNOSIS AND TESTING,
POWER SEAT..................8N-17,8N-60
TRACK - INSTALLATION, BENCH SEAT . . . 23-104
TRACK - INSTALLATION, DRIVER POWER
SEAT.........................8N-16,8N-59
TRACK - INSTALLATION, FRONT SEAT
RISER - MANUAL....................23-95
TRACK - INSTALLATION, PASSENGER
POWER SEAT..................8N-18,8N-61
TRACK - OPERATION, DRIVER POWER
SEAT.........................8N-15,8N-58
TRACK - OPERATION, PASSENGER
POWER SEAT..................8N-17,8N-60
TRACK & RACK - DESCRIPTION, LOWER
DRIVE UNIT........................8N-34
TRACK & RACK - INSTALLATION,
LOWER DRIVE UNIT..................8N-34
TRACK & RACK - OPERATION, LOWER
DRIVE UNIT........................8N-34
TRACK & RACK - REMOVAL, LOWER
DRIVE UNIT........................8N-34
TRACK - REAR COVER - INSTALLATION,
FRONT SEAT........................23-96
TRACK - REAR COVER - REMOVAL,
FRONT SEAT........................23-96
TRACK - REMOVAL, BENCH SEAT.......23-104
TRACK - REMOVAL, DRIVER POWER
SEAT.........................8N-16,8N-59
TRACK - REMOVAL, FRONT SEAT RISER
- MANUAL..........................23-94
TRACK - REMOVAL, PASSENGER POWER
SEAT.........................8N-18,8N-61
TRACK BAR - DESCRIPTION.............2-46
TRACK BAR - INSTALLATION............2-46
TRACK BAR - OPERATION...............2-46
TRACK BAR - REMOVAL................2-46
TRACK MANUAL ADJUSTER -
INSTALLATION, FRONT SEAT...........23-95
TRACK MANUAL ADJUSTER - REMOVAL,
FRONT SEAT........................23-95
TRACK POWER ADJUSTER -
INSTALLATION, FRONT SEAT...........23-95
TRACK POWER ADJUSTER - REMOVAL,
FRONT SEAT........................23-95
TRACTION CONTROL SWITCH -
DIAGNOSIS AND TESTING..............5-82
TRACTION CONTROL SYSTEM -
DESCRIPTION........................5-76
TRACTION CONTROL SYSTEM -
OPERATION
..........................5-77
TRANSAXLE - ASSEMBLY, 41TE
AUTOMATIC
.......................21s-184
TRANSAXLE - ASSEMBLY, T850 MANUAL
. 21-42
TRANSAXLE - DESCRIPTION, 40TE
AUTOMATIC
........................21s-25
TRANSAXLE - DESCRIPTION, 41TE
AUTOMATIC
........................21-117TRANSAXLE - DESCRIPTION, T850
MANUAL...........................21-21
TRANSAXLE - DISASSEMBLY, 41TE
AUTOMATIC.......................21s-166
TRANSAXLE - DISASSEMBLY, T850
MANUAL...........................21-35
TRANSAXLE - INSTALLATION, T850
MANUAL...........................21-51
TRANSAXLE - OPERATION, 40TE
AUTOMATIC........................21s-27
TRANSAXLE - OPERATION, 41TE
AUTOMATIC........................21-119
TRANSAXLE - OPERATION, T850
MANUAL...........................21-24
TRANSAXLE - REMOVAL, T850 MANUAL . . 21-31
TRANSAXLE - SPECIAL TOOLS, T850.......6-6
TRANSAXLE - SPECIAL TOOLS, T850.....21-58
TRANSAXLE - SPECIFICATIONS, 41TE . . . 21-181,
21s-87
TRANSAXLE - SPECIFICATIONS, T850
MANUAL...........................21-56
TRANSAXLE FLUID - DESCRIPTION,
AUTOMATIC/MANUAL...................0-4
TRANSAXLE GENERAL DIAGNOSIS -
DIAGNOSIS AND TESTING, 41TE.......21-119
TRANSAXLE GENERAL DIAGNOSIS -
DIAGNOSIS AND TESTING, 4XTE.......21s-27
TRANSAXLE HYDRAULIC SCHEMATICS,
SCHEMATICS AND DIAGRAMS - 41TE . . . 21-169
TRANSAXLE HYDRAULIC SCHEMATICS,
SCHEMATICS AND DIAGRAMS - 4XTE . . . 21s-75
TRANSAXLE, SPECIAL TOOLS - 41TE
AUTOMATIC.........................21-183
TRANSDUCER - DESCRIPTION, A/C
PRESSURE.........................24-21
TRANSDUCER - DIAGNOSIS AND
TESTING, A/C PRESSURE..............24-22
TRANSDUCER - INSTALLATION, A/C
PRESSURE.........................24-22
TRANSDUCER - OPERATION, A/C
PRESSURE.........................24-21
TRANSDUCER - REMOVAL, A/C
PRESSURE.........................24-22
TRANSFER UNIT - DESCRIPTION,
POWER.............................21-1
TRANSFER UNIT - OPERATION, POWER....21-3
TRANSFER UNIT FLUID - DESCRIPTION,
AWD POWER..........................0-6
TRANSFER UNIT, SPECIAL TOOLS - SDP
POWER.............................21-8
TRANSMISSION CONTROL MODULE -
DESCRIPTION.......................8E-20
TRANSMISSION CONTROL MODULE -
OPERATION.........................8E-20
TRANSMISSION CONTROL RELAY -
DESCRIPTION...............21-247,21s-150
TRANSMISSION CONTROL RELAY -
OPERATION.................21-248,21s-150
TRANSMISSION OIL COOLER -
DESCRIPTION........................7-37
TRANSMISSION OIL COOLER -
INSPECTION.........................7-37
TRANSMISSION OIL COOLER -
INSTALLATION........................7-37
TRANSMISSION OIL COOLER -
REMOVAL...........................7-37
TRANSMISSION OIL COOLER LINES -
INSTALLATION........................7-38
TRANSMISSION OIL COOLER LINES -
REMOVAL...........................7-38
TRANSMISSION RANGE SENSOR -
DESCRIPTION...............21-248,21s-150
TRANSMISSION RANGE SENSOR -
INSTALLATION...............21-249,21s-152
TRANSMISSION RANGE SENSOR -
OPERATION.................21-248,21s-151
TRANSMISSION RANGE SENSOR -
REMOVAL..................21-249,21s-151
TRANSMITTER - DESCRIPTION,
UNIVERSAL
........................8M-10
TRANSMITTER - DIAGNOSIS AND
TESTING, KEYLESS ENTRY
........8N-42,8N-5
TRANSMITTER - DIAGNOSIS AND
TESTING, UNIVERSAL
................8M-10
TRANSMITTER - OPERATION,
UNIVERSAL
........................8M-10
TRANSMITTER CODES - STANDARD
PROCEDURE, ERASING
...............8M-11
36 INDEXRS
Description Group-Page Description Group-Page Description Group-Page