2004 Alfa Romeo 156 Owner handbook (in English)

GETTING TO KNOW YOUR CAR
143
SYSTEM ACTIVATIONWARNINGOpening the driver’s door,
the Selespeed starts the hydraulic part of
the system to prepare it for the engine to be
started. This function (noted by the turning
of the electric pump) is deactivated after 10
openings/closings of the door that are not
followed by actual system activation using
the ignition key.
Turning the ignition key to MAR, all the
segments of the display (A-fig. 126), the
gearbox failure warning light (B-fig. 126)
and the word CITYlight up. After about one
second, the display indicates the gear en-
gaged (N, 1, 2, 3, 4, 5, R); from this mo-
ment, the Selespeed system accepts
gearshift commands.
WARNINGIf after 10 seconds the dis-
play segment do not display the gear en-
gaged or the failure warning light stays on,
turn the ignition key to STOPand wait for
the display to go off, then repeat the sys-
tem activation procedure. If the fault per-
sists, contact Alfa Romeo Authorized Ser-
vices
OPERATION WITH THE
ENGINE OFFWARNINGBefore operating the gear-
shift control lever, always check the gear en-
gaged on the display (N, 1, 2, 3, 4, 5, R).
When the engine is off and the vehicle is
stationary, it is possible to engage all the
gears.
With the vehicle stationary and with the
brake pedal pressed, requests to shift gear
are accepted onlyif they are carried out
through the control lever on the central con-
sole.To request gearshifting, in addition to keep-
ing the brake pedal pressed it is necessary to:
– to increase gear (+) (fig. 127) push
the lever “forwards” (if the car is in first gear
this shifts to second, if it is in second gear
it goes to third and so on up to fifth). If the
system is in neutral (N) or reverse (R) the
forward movement on the lever causes en-
gagement of first gear (1).
– to shift down (–) (fig. 127) push the
lever backwards (if the car is in fifth gear
it moves to fourth, if fourth gear is engaged
it shifts to third and so on down to first).
fig. 127
A0B0272m

GETTING TO KNOW YOUR CAR
144
WARNINGOnce a gear has been shifted
it is necessary to release the gearshift con-
trol lever immediately after making the re-
quest. A prolonged action (over 10 seconds)
causes automatic shifting to CITY; previous
conditions are restored when releasing the
lever.
WARNINGIf wanting to leave the car
parked on a sloping road with a gear en-
gaged to keep it braked, it is necessary to
check that the Infocenter display shows the
new gear engaged and then wait for 1 to
2 seconds before releasing the brake pedal
to allow complete clutch engagement.
fig. 129
A0B0274m
To put the gearbox in neutral (N), start-
ing from the condition with the vehicle sta-
tionary and the brake pedal pressed, it is
necessary to move the gearshift control lever
to the right (fig. 128).From any gear (N, 1, 2, 3, 4, 5) and
with the vehicle practically at a standstill,
it is possible to request engagement of re-
verse gear, pushing the lever to the right and
then backwards (fig. 129). If the vehi-
cle is on the move, the request is not ac-
cepted; wait for the car to stop and then
request reverse gear engagement againfig. 128
A0B0273m

GETTING TO KNOW YOUR CAR
145
STARTING THE ENGINEThe engine can be started with the gear
engaged or in neutral (N), provided that the
brake pedal is pressed down.
WARNINGKeep the brake pedal
pressed during the starting operation. As the
brake pedal stiffens if it is pressed repeat-
edly with the engine off, in this situation, to
allow the engine to be started, it is neces-
sary to increase the pressure exerted on the
pedal itself.
After starting, the gearbox automatically
sets to neutral, the display shows the let-
ter (N) and the system selects the operat-
ing mode stored before switching off.
TURNING THE ENGINE OFF
AND SYSTEM DEACTIVATIONTurning the ignition key to STOPthe en-
gine switches off but the Selespeed system
still remains active, waiting for the vehicle
to stop completely. After about 2 - 4 seconds
from when the key has been turned to the
STOPposition, the hydraulic part is deac-
tivated and immediately afterwards the dis-
play on the rev counteralso goes out ; the
Selespeed system is only deactivated at this
point.
The gear selected before turning the en-
gine off remains engaged.
If the engine stops with the gearbox in
neutral (N), the buzzer draws the attention
of the driver so that the vehicle can be put
in safety conditions engaging the first gear
(1) or reverse (R). In this case, it is nec-
essary to turn the ignition key to MARand
with the brake pedal pressed, engage first
gear (1) or reverse (R).
If the engine fails to start
with the gear engaged, the
driver is alerted of the potentially
dangerous situation due to the fact
that the gearbox has automatically
set to neutral by the buzzer and
the display on the rev counter.
WARNING
NEVER leave the car with
the gearbox in neutral (N).
WARNING
Never remove the key
when the car is on the
move, because in addition to the
fact that the Selespeed system
would not work properly until
stopping the car, the steering
wheel would automatically lock at
the first turn.
WARNING
It is absolutely necessary
to turn off the engine con-
sequently deactivating the Sele-
speed system keeping the brake
pedal pressed: release the pedal
ONLY when the display on the rev
counter goes off.
WARNING

GETTING TO KNOW YOUR CAR
146
WARNINGS– With the vehicle stationary and a gear
engaged, always keep the brake pedal
pressed until you decide to move off;
– in prolonged stops with the engine run-
ning it is advisable to keep the gearbox is
neutral;
– when the car is parked on a slope, do
not use the pick-up manoeuvre to keep the
vehicle stopped; use the brake pedal and
work on the accelerator pedal only when
you decide to move off;
– use second gear onlywhen necessary
to obtain better control of pick-up in low
speed manoeuvres;
– if, with reverse gear engaged, you need
to engage first gear or vice versa, shift gear
only when the car is completely stationary
and with the brake pedal pressed. This should not be considered as a fault as
it is part of the operating logic. For the same
reason, in the event of sticking on reverse,
the system commands partial clutch closing
to allow engagement of the gear; in this
case engagement of reverse gear (R) will
be less comfortable.
Moving off of the vehicle is obtained:
1) releasing the brake pedal;
2) gradually operating the accelerator
pedal.
The vehicle pick-up torque is higher the
more the accelerator pedal is pressed.
MOVING OFFWith the engine running and the vehicle
stationary, the gears that can be engaged
for moving off are only first (1), second (2)
or reverse (R).
To engage them it is possible to use the
control lever on the centre console, with the
brake pedal pressed, as the levers on the
steering wheel allow gear engagement only
over 0.5 km/h.
WARNINGReverse gear (R) can be en-
gaged from each of the following other ra-
tios: neutral (N), first gear (1) or second
gear (2). If the car is on the move, the re-
quest is not accepted; it is necessary to wait
for the car to be completely stopped and
then request reverse (R) again.
The driver is informed of the reverse gear
engaged condition by the intermittent sound
of the buzzer as well as by the display on
the rev counter.
WARNINGIf while shifting from reverse
(R)/first gear (1) to neutral (N)/first gear
(1) sticking occurs on the first gear, the sys-
tem automatically engages second gear
(2).
After a request to shift
gear with the vehicle sta-
tionary, before pressing the accel-
erator pedal to make the car start,
the driver must always check that
the gear engaged shown on the
display is the one required.
WARNING

GETTING TO KNOW YOUR CAR
147
STOPPING THE CARTo stop the vehicle, simply release the ac-
celerator pedal and, if necessary, operate
the brake pedal.
Regardless of the gear engaged and of the
operating mode activated (MANUALor
CITY), the system automatically disen-
gages the clutch and downshifts gear.
If you intend to move off again without
having completely stopped the car, this way
the most suitable gear ratio for re-acceler-
ating will be available.
Stopping the vehicle, the system auto-
matically engages first gear (1). Though strongly inadvisable, if due to un-
foreseen circumstances when driving down-
hill the car is allowed to travel with the gear-
box in neutral (N), when the engagement
of a gear is requested, the system auto-
matically engages the best gear to allow
transmission of the torque to the wheels in
relation to the speed of the car.
Downhill with the gear engaged and the
accelerator released (if the vehicle is trav-
elling), if a certain pre-established speed is
exceeded, the system automatically en-
gages the clutch to provide adequate engine
braking.
Due to safety reasons, the Selespeed sys-
tem activates the buzzer when:
– clutch overheating occurs during vehicle
starting; in this case, it is necessary to
“force” moving off avoiding hesitations or
to release the accelerator and use the brake
pedal to park the vehicle if the car is on a
slope;
– the car moves in the opposite direction
to the gear engaged, (e.g.: vehicle moving
forward with reverse engaged); in this sit-
uation it is necessary to stop the vehicle and
keeping the brake pedal pressed, engage
the gear correctly.Still for safety reasons, when the vehicle
is stationary, with the engine started and
gear (1), (2) or (R) engaged, the system
activates the buzzer and shifts to neutral
(N) automatically when:
– there is no action on the accelerator
and/or brake pedal for at least 3 minutes;
– the brake pedal is pressed for over 10
minutes;
– the driver’s door is opened and the ac-
celerator and brake pedal are not pressed
for at least 1 second.

GETTING TO KNOW YOUR CAR
148
fig. 131
A0B0270m
OPERATIONThe gearbox can work in two operating
modes:
– the first is semiautomatic (MANUAL),
in which the driver directly decides when to
shift gear;
– the second is completely automatic
(CITY), in which the system decides di-
rectly when to shift gear according to the
type of driving.
The CITYmode can be selected by press-
ing the specific button CITYon the gearbox
lever knob; when this mode is selected, the
CITY sign appears on the display fitted on
rev counter.
SEMIAUTOMATIC OPERATION
(MANUAL) In the MANUALoperating mode the dis-
play on the rev counter shows the gear en-
gaged.
In this operating mode, the decision to
change gear is left to the driver who decides
the most appropriate moment.
The requests to change gear can take place
through:
– the control lever on the centre console
(A-fig. 130);
– the levers on the steering wheel
(fig. 131), which can be used only when
the vehicle speed exceeds 0.5 km/h.The MANUALoperating mode is set
when, with the CITYmode selected, the
CITYbutton (B-fig. 130) is pressed
again, excluding the previously selected
mode.fig. 130
A0B0271m

GETTING TO KNOW YOUR CAR
149
When shifting gear, releasing the acceler-
ator pedal is not necessary because the Se-
lespeed system directly controls the engine
so as to:
– reduce and then increase the engine
torque;
– adapt the engine speed to the new gear
ratio engaged.
When downshifting, double de-clutching
(acceleration of the engine to bring it to the
speed necessary with the new gear ratio) is
carried out automatically.
The move to neutral (N) command is ac-
cepted when the car speed exceeds 20 km/h.
The command to engage reverse gear (R)
is accepted only if the car is stationary.With the accelerator pedal pressed by over
60% of its stroke and with an engine speed
of over 5,000 rpm, gearshifting becomes
quicker.
In the MANUALmode there are some
automatic/safety devices which make dri-
ving easier:
– when slowing down, the clutch is
opened and the gear ratio is reduced auto-
matically to be ready for possibly picking up
speed again; if not, stopping the vehicle,
first gear (1) will be engaged automatically;
– request to change gear that could take
the engine above the maximum rpm or be-
low the minimum permissible rpm are not
accepted;– if the engine reaches the maximum per-
missible rpm and accelerating continues
(without coming into operation of the VDC
system), the system automatically engages
a higher gear; with the activation of the VDC
system, with the maximum engine rpm,
gear shifting is excluded;
– if sticking occurs during the engagement
of a gear, the system firstly tries to engage
the required gear again and, if it is still not
possible, it automatically engages the im-
mediately higher one to avoid leaving the
vehicle in neutral speed.
WARNINGIt is advisable to wait for a
gearshift to end before requesting another
one, this will avoid multiple requests in quick
succession.

GETTING TO KNOW YOUR CAR
150
AUTOMATIC OPERATION (CITY)The CITYautomatic operating mode is se-
lected pressing the button (A-fig. 132),
at the base of the gearshift lever.
In addition to the gear, the display on the
rev counter will show the word CITY.
The system decides directly when gearshift-
ing according to the engine running speed
and the driving style.
Quickly releasing the accelerator pedal, the
system does not engage a higher gear in or-
der to maintain an adequate level of engine
brake.
FAILURE SIGNALLINGFailures to the Selespeed gearbox are in-
dicated by the
t
(A-fig. 133) warn-
ing light on the instrument cluster.
When the system is turned on (turning the
ignition key to MAR), the warning light
should turn on glowing steadily for about
4 seconds and then turn off.
If the warning light stays on it means that
a fault to the gearbox has been detected; at
the same time a buzzer sounds intermit-
tently for 4 seconds to attract the driver's
attention.In the case of a fault to the gearshift lever,
the system automatically activates the au-
tomatic CITYmode to allow the car to
reach the nearest Authorized Alfa Romeo
Services to have the fault detected elimi-
nated.
In the event of faults to other components
of the gearbox, the system only allows the
engagement of certain ratios: first gear (1),
second (2) and reverse (R).
fig. 132
A0B0269m
fig. 133
A0B0383m
If the warning light
t
comes on, contact the Alfa
Romeo Authorized Services
as soon as possible to remove the
fault.In case of transmission
fault, contact the Alfa
Romeo Authorized Services as
soon as possible to check the sys-
tem.
WARNING