2004 Acura RSX Owner's Manual

Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
cargo area or pull a trailer,
readjustment may be required.
Adjustment should be done by an
Acura dealer or other qualif ied
mechanic.Your vehicle has two bulbs on each
side, f our in total. Make sure you are
replacing the bulb that is burned out.
Your vehicle uses halogen headlight
bulbs. Handle a bulb by its plastic
case and protect the glass f rom
contactwithyourskinorhard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth.
If you need to the change a
headlight bulb on the passenger’s
side, remove the power steering
reservoir f rom the bracket.
NOTE: Halogen headlight bulbs get
very hot when lit. Oil, perspiration,
or a scratch on the glass can cause
the bulb to overheat and shatter.
1.
Lights
Headlight A iming
Replacing a Headlight Bulb
Maint enance174
Passenger’s side
POWER STEERING RESERVOIR

Insert the new bulb into the hole,
making sure the tabs are in their
slots. Pivot the hold-down wire
back in place, and clip the end into
the slot.
Install the rubber seal and make
sure it is right side up; it is marked
‘‘TOP.’’
Push the electrical connector onto
the tabs of the new bulb. Make
sure it locks in place.
(Passenger’s side)
Install the power steering
reservoir on the bracket.
Remove the electrical connector
f rom the bulb by pulling the
connector straight back.
Remove the rubber weather seal
by pulling on the tab.
Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way, and remove the bulb.
If you need to change a headlight
bulb on the driver’s side, remove
the bolt from the battery hold-
down, and caref ully push the
battery toward the windshield to
obtain enough working space.
Pull the battery back to its original
position, then install the bolt in the
hold-down, and tighten it securely. (Driver’s side)
3.
4. 5.
6.
7.
8.
2.
Lights
Maint enance175
BULB
WEATHER
SEAL
HOLD
DOWN WIRE CONNECTOR
Driver’s side

If you need to change a f ront turn
signal bulb on the passenger’s side,
remove the power steering
reservoir f rom the bracket.If you need to change a f ront turn
signal bulb on the driver’s side,
remove the bolt f rom the battery
hold-down, and caref ully push the
battery toward the windshield to
obtain enough working space.Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
1.
2.
3.
Lights
Maint enance
Replacing a Front T urn Signal
Bulb
176
Passenger’s side
POWER STEERING RESERVOIR BULB
Driver’s side

Pull the bulb straight out of its
socket.
The f ront parking bulb is next to
the headlight bulb.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Install the new bulb into the
socket.
(Passenger’s side)
Install the power steering
reservoir on the bracket.
(Driver’s side)
Place the battery in its original
position, then install the bolt in the
hold-down, and tighten it securely.
Install the new bulb into the
socket.
3.
4.
5.
1.
2.4.
Replacing a Front Parking Bulb
Lights
Maint enance177
BULB

Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Insert the socket back into the
light assembly. Turn it clockwise
to lock it in place.
Testthelightstomakesurethe
new bulb is working.
Reinstall the high-mount brake
light cover.
Open the hatch.
Remove the high-mount brake
light cover by pivoting it toward
the back of the vehicle.
Remove the socket by turning it
one-quarter turn counterclockwise. Open the hatch. Remove the light
assembly cover by pulling on the
tabontheoutsideedge.
2.
3. 1. 4.
5.
6.
7.
1.
Lights
Maint enance
Replacing Rear Bulbs
Replacing a High-mount Brake
Light Bulb
178
COVER
COVER BULB

Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Testthelightstomakesurethe
new bulb is working.
Install the light assembly cover.
Make sure it locks in place.
Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms. Remove the socket by turning it
one-quarter turn counterclockwise. Determinewhichof thefivebulbs
is burned out: brake/taillight, turn
signal light, side marker light,
back-up light, or taillight.
2.
3.
4. 5.
6.
7.
Lights
Maint enance179

If your seat belts get dirty, use a sof t
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air dry bef ore
you use the vehicle.
Dirt build-up in the loops of the seat
belt anchors can cause the belts to
retract slowly. Wipe the insides of
the loops with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.The driver’s f loor mat that came
with your vehicle hooks over the
f loor mat anchor. This keeps the
f loor mat f rom sliding f orward and
possibly interf ering with the pedals.
If you remove the driver’s f loor mat,
make sure to re-anchor it when you
putitbackinyourvehicle.If you use a non-Acura f loor mat,
make sure it f its properly and that it
canbeusedwiththefloormat
anchor. Do not put additional f loor
mats on top of the anchored mat.
This f ilter removes the dust and
pollenthatisbroughtinfromthe
outside through the heating and
cooling system.
Have your Acura dealer replace this
f ilter every 30,000 miles (48,000 km)
under normal conditions. It should
be replaced every 15,000 miles
(24,000 km) if you drive primarily in
urban areas that have high
concentrations of soot in the air, or if
the airflow from the heating and
cooling system becomes less than
usual.
Seat Belts, Floor Mats, Dust and Pollen Filter
Maint enance
Seat Belts
Floor Mats
Dust and Pollen Filter
180
LOOP

CONT INUED
Check the condition of the wiper
blades at least every six months.
Look f or signs of cracking in the
rubber, or areas that are getting
hard. Replace the blades if you f ind
these signs, or if they leave streaks
and unwiped areas when used.To replace a blade (f ront or rear):Raise the wiper arm of f the
windshield or rear window. Disconnect the blade assembly
fromthewiperarmbypushingin
the lock tab. Hold the lock tab in
while you push the blade assembly
toward the base of the arm.
2.
1.
Wiper Blades
Maint enance181
WIPER ARMS
LOCK TAB