2003 TOYOTA AVENSIS location

MO
NEW MODEL OUTLINE

\b 

\b 

\b 
Front TweeterFront Door Speaker
Glass Antenna
Rear TweeterRear Door Speaker
Front Door Speaker
Rear Tweeter
Rear Door Speaker
Sedan Model
Glass Antenna
Liftback Model
Wagon Model
Glass Antenna

\b 
MO-19
Location
Multi-information Display

A multi-information display is standard
equipment on MID TECHNICAL and
MID ELEGANT grade Europe models
and available as an option for ENTRY
grade models.

Average fuel consumption after
refueling, momentary fuel consumption,
average vehicle speed, driving distance
after engine start, and driving range can
be displayed.

The vehicle information screens can be
switched and the average vehicle speed
or driving distance after engine start can
be reset using the steering pad switch.
http://vnx.su

MO
NEW MODEL OUTLINE

\b 

\b 

\b 
Front TweeterFront Door Speaker
Glass Antenna
Rear TweeterRear Door Speaker
Front Door Speaker
Rear Tweeter
Rear Door Speaker
Sedan Model
Glass Antenna
Liftback Model
Wagon Model
Glass Antenna

\b 
MO-19
Location
Multi-information Display

A multi-information display is standard
equipment on MID TECHNICAL and
MID ELEGANT grade Europe models
and available as an option for ENTRY
grade models.

Average fuel consumption after
refueling, momentary fuel consumption,
average vehicle speed, driving distance
after engine start, and driving range can
be displayed.

The vehicle information screens can be
switched and the average vehicle speed
or driving distance after engine start can
be reset using the steering pad switch.
http://vnx.su

010LF±01






D25016
±
INTRODUCTION REPAIR INSTRUCTION
01±5
AVENSIS REPAIR MANUAL (RM1018E)
REPAIR INSTRUCTION
PRECAUTION
1. BASIC REPAIR HINT
(a) HINTS ON OPERATIONS
1Looks
Always wear a clean uniform.

Hat and safety shoes must be worn.
2Vehicle protection
Set a grill cover, fender cover, seat cover and floor mat before starting operation.
3Safe operation

When working with 2 or more persons, be sure to check the safety of one \
another.

When working with the engine running, pay attention to providing ventila\
tion for exhaust fumes in the work-
shop.

When working with high±temperatures, rotating, moving or vibrating pa\
rts, be careful not to burn or injure
yourself.

When jacking up the vehicle, be sure to support the specified location w\
ith a safety stand.

When lifting up the vehicle, use safety equipment.
4Preparation of tools and
measuring gauge
Before starting repairs, prepare the tool stand, SST, gauge, oil, shop rag and parts for replacement.
5
Removal and installation,
disassembly and assem-
bly operations

Diagnose with a thorough understanding of the trouble condition and perf\
orm effective operation.

Before removing the parts, check the general condition of the assembly, and for deformation and damage.

When the structure is complicated, take a notes or make matchmarks as no\
t to make mistakes that affect the
function of the parts.

Clean and wash the removed parts if necessary and assemble them after a \
thorough check.
6Removed parts

Place the removed parts in the correct order to avoid mixing them up or \
making them dirty.

As for non±reusable parts such as gaskets, O±rings, and self±lo\
cking nuts, replace them with new ones
following the instructions in this manual.

Organize the parts that were replaced in a box and show them to the cust\
omer.
http://vnx.su

Z11554
Seal Lock Adhesive
BE1367
Medium Current Fuse and High Current
Fuse Equal Amperage Rating


V35002
IllustrationSymbol Part Name Abbreviation
FUSE
MEDIUM CURRENT FUSE
HIGH CURRENT FUSE FUSE
M±FUSE H±FUSE
01±6
±
INTRODUCTION REPAIR INSTRUCTION
AVENSIS REPAIR MANUAL (RM1018E)
(b) JACKING UP AND SUPPORTING VEHICLE (1) Care must be taken when jacking up and supporting the vehicle. Be sure to li\
ft and support thevehicle at the proper locations (See page 01±19).
(c) PRECOATED PARTS(1) Precoated parts such as bolts, nuts, etc., are
coated with a seal lock adhesive at the factory.
(2) If a precoated part is retightened, loosened or caused to move in any way, it must be recoated with
the specified adhesive.
(3) When reusing precoated parts, clean off the old
adhesive and dry the part with compressed air.
Then apply the specified seal lock adhesive to the
bolt, nut or threads.
NOTICE:
Check the torque with the lower limit value of the torque tol-
erance.
(4) Depending on the seal lock agent to be applied,there may be cases where it is necessary to leave
it for a specified time until it hardens.
(d) GASKETS (1) When necessary, use a sealer on gaskets to prevent leaks.
(e) BOLTS, NUTS AND SCREWS (1) Carefully follow all the specifications for tightening torques. Always u\
se a torque wrench.
(f) FUSES(1) When replacing fuses, be sure that a new fuse hasthe correct amperage rating. DO NOT exceed the
rating, or use one with a lower rating.
http://vnx.su

D25081
Spring Type Clamp
Clamp Track
D20025
CG
DLC3
TS
D30964
±
INTRODUCTION REPAIR INSTRUCTION
01±17
AVENSIS REPAIR MANUAL (RM1018E)
6. HANDLING OF HOSE CLAMPS
(a) Before removing the hose, check the depth of the insert-
ing portion and the clamp position to restore it surely.
(b) Change a deformed or dented clamp for a new one.
(c) In case of reusing a hose, attach the clamp on the clamp track portion of the hose.
(d) For a spring type clamp, adjust it by adding force to the
arrow mark direction after the installation.
7. FOR VEHICLES EQUIPPED WITH MOBILE COMMU- NICATION SYSTEMS
(a) Install the antenna as far away from the ECU and sensors of the vehicle electronic systems as possible.
(b) Install an antenna feeder at least 20 cm (7.87 in.) away from the ECU and sensors of the vehicle electronic sys-
tems. For details of the ECU and sensors locations, refer
to the section on applicable components.
(c) Prevent the antenna feeder from getting entangled with the other wiring, and keep the antenna feeder separate
from other wiring as much as possible.
(d) Check that the antenna and feeder are correctly adjusted.
(e) Do not install any high±powered mobile communication system.
8. FOR VEHICLES EQUIPPED WITH TRACTION CONTROL (TRC) SYSTEM
(a) NOTICES WHEN USING 2±WHEEL DRUM TESTER
(1) When using a 2±wheel drum tester such as a speedometer tester, a combination tester ofspeedometer and brake, chassis dynamometer or else, always turn the TRC system off via the
TRC OFF switch before measurement.
NOTICE:
TRC system OFF condition can be confirmed by the indication, ºTRC OFF\
º, of the warning light in
the combination meter.
9. FOR VEHICLES EQUIPPED WITH VEHICLE SKIDCONTROL (VSC) SYSTEM
(a) NOTICES WHEN USING DRUM TESTER
(1) When using a drum tester, be sure to start the en-gine with the ignition OFF, and connect SST to the
terminals TS and CG of the DLC3 before measure-
ment in order to prohibit the VSC operation.
SST 09843±18040
http://vnx.su

010B5±11
D25082
Rubber Attachment
D27697
: SUPPORT POSITION, PAN
TOGRAPH JACK POSITION
: CENTER OF VEHICLE GRAVITY
(unload condition)
: JACK POSITION
±
INTRODUCTION REPAIR INSTRUCTION
01±19
AVENSIS REPAIR MANUAL (RM1018E)
VEHICLE LIFT AND SUPPORT LOCATIONS
1. NOTICE ABOUT VEHICLE CONDITION WHEN JACKING UP
(a) As a rule, the vehicle must be unloaded when jacking up. Never jack up o\
r lift up the vehicle loaded
with things of heavy weight.
(b) When removing any parts of heavy weight like the engine and transmission, the center of gravity of the vehicle moves. Place a balance weight so as to keep it from rolling,\
or hold the jacking support
location using the mission jack.
2. NOTICE FOR USING 4 POST LIFT
(a) Follow the instruction manual for a safety operation.
(b) Do not damage tires or wheels with a free wheel beam.
(c) Using a wheel stopper, fix the vehicle.
3. NOTICE FOR USING JACK AND SAFETY STAND
(a) Work in the flat place using a wheel stopper at all times.
(b) Use a safety stand with a rubber attachment, as shownin the illustration.
(c) Support the specified location with a jack and safety stand accurately.
(d) When jacking up the front wheels, release the parking
brake and place wheel stoppers only behind the rear
wheels. When jacking up the rear wheels, place wheel
stoppers only in front of the front wheels.
(e) Do not work or leave the vehicle supported only by a jack. Be sure to support the vehicle with a safety stand.
(f) When jacking up only the front wheels or only the rear wheels, place wheel stoppers to both sides of the wheels that contact ground.
(g) When jacking down the vehicle with its front wheels jacked up, release t\
he parking brake and place wheel stoppers only in front of the rear wheels. When jacking down the v\
ehicle with its rear wheels
jacked up, place wheel stoppers only behind the front wheels.
http://vnx.su

D30400
Swing Arm Type Lift
Plate Type LiftCenter of Lift
: CENTER OF VEHICLE
GRAVITY (unloaded condition) Rubber Attachment
AttachmentBAL
Attachment Dimensions
85 mm (3.35 in.)
200 mm (7.87 in.)
100 mm (3.94 in.) 70 mm
(2.76 in.)
C
01±20
±
INTRODUCTION REPAIR INSTRUCTION
AVENSIS REPAIR MANUAL (RM1018E)
4. NOTICE FOR USING SWING ARM TYPE LIFT
(a) Follow the instruction manual of the lift for a safe operation.
(b) Use a cradle with a rubber attachment, as shown in the illustration.
(c) Set in the vehicle so as to make its center of gravity as close as possible\
to the center of the lift. (ºLº becomes short.)
(d) Place the vehicle horizontally by adjusting the height of the cradle, and match th\
e groove of the cradle and the safety stand support location accurately.
(e) Be sure to lock the swing arm during the operation.
(f) Lift the vehicle up until the tires float, and shake the vehicle to make\
sure that the vehicle is stable.
5. NOTICE FOR USING PLATE TYPE LIFT
(a) Follow the instruction manual of the lift for a safe operation.
(b) Use a plate lift attachment.
(c) Be sure to set the vehicle to the specified position.
Right and left set position
Place the vehicle over the center of the lift.
Front and rear set position
Align the cushion gum ends of the plate with the attachment lower ends (\
A and C).

Align the attachment upper end (B) with the rocker flange front side n\
otch.
(d) Lift the vehicle up until the tires float a bit, and shake the vehicle t\
o make sure that the vehicle is stable.
http://vnx.su

A78447
A78448
Triangle Mark
Matchmark
A78446
SST
Rib
A78449
Arrow Mark
±
FUEL FUEL PUMP ASSY (GASOLINE)
11±87
AVENSIS REPAIR MANUAL (RM1018E)
(b) Remove the fuel pump gauge retainer.
(c) Remove the fuel suction w/ pump & gage tube.
NOTICE:
Be careful that the arm of the fuel sender gage should not
be bent.
(d) Remove the gasket from the tank.
8. INSTALL FUEL SUCTION W/PUMP & GAGE TUBE
ASSY
(a) Install a new gasket to the fuel tank.
(b) Install the fuel suction w/ pump & gage tube.
NOTICE:
Be careful that the arm of the fuel sender gage should not
be bent.
(c) Align the triangle mark of the fuel suction w/ pump & gage tube with the matchmark location the fuel tank.
(d) Temporarily install the fuel pump gauge retainer.
(e) Using SST, tighten the fuel pump gauge retainer until the arrow mark is aligned with the center mark on the fuel
tank.
SST 09808±14010
NOTICE:
Do not use other tools in this operation. Damage to the fuel
pump gauge retainer and the fuel tank may result.
HINT:
A rib on the fuel pump gauge retainer can be fitted into a tip of
the SST.
(f) Check that the arrow mark and center mark are aligned as shown in the illustration.
http://vnx.su