2003 TOYOTA AVENSIS child lock

61±18
±
SEAT BELT REAR SEAT BELT (SEDAN MODELS)
AVENSIS REPAIR MANUAL (RM1018E)
(1) Check that the belt does not lock within 15
of tilt in
all directions but locks with over 45
of tilt when
gently moving the retractor.
If operation is not as specified, replace the belt assy.
(c) Install the belt with the bolt on the floor anchor side. Torque: 42 N
m (430 kgf
cm, 31 ft
lbf)
NOTICE:
Make sure that the anchor part does not run onto the protru-
sion part of the floor panel.
(1) Check that the belt locks by pulling it out quickly af-ter installation.
If operation is not as specified, replace the belt assy.
(d) Check the ELR lock.
NOTICE:
The check should be performed with the a ssembly
installed.
(1) Check that the belt locks by pulling it out quickly af-ter installation.
If operation is not as specified, replace the belt assy.
(e) Check the fastening function of the child restraint system.
NOTICE:
The check should be performed with the a ssembly
installed. (1) Check that the belt cannot be pulled out any morebut rewinds after being pulled out fully.
(2) Check that the belt can be pulled out and rewound after the belt has been fully rewound.
If operation is not as specified, replace the belt assy.
20.INSTALL REAR SEAT ASSY (See page 72±27, 72±32)
http://vnx.su

B70206
LockUnlock
45

B66570
Protrusion Part
Front
Front
Mark
Protrusion Part
B66568Lock
Unlock
45

±
SEAT BELT REAR SEAT BELT (WAGON MODELS)
61±25
AVENSIS REPAIR MANUAL (RM1018E)
(b) Check the degree of tilt when the belt begins to lock the
ELR.
NOTICE:
Do not disassemble the retractor.
(1) Check that the belt does not lock within 15
of tilt in
all directions but locks with over 45
of tilt when
gently moving the retractor.
If operation is not as specified, replace the belt assy.
(c) Install the belt with the bolt on the floor anchor side. Torque: 42 N
m (430 kgf
cm, 31 ft
lbf)
(d) Check the ELR lock.
NOTICE:
The check should be performed with the a ssembly
installed. (1) Check that the belt locks by pulling it out quickly af-ter installation.
HINT:
The seat belt does not lock when it is pulled out to a length of
955 mm (37.60 in.) or less.
If operation is not as specified, replace the belt assy.
(e) Check the fastening function of the child restraint system.
NOTICE:
The check should be performed with the a ssembly
installed. (1) Check that the belt cannot be pulled out any more
but rewinds after being pulled out fully.
(2) Check that the belt can be pulled out and rewound after the belt has been fully rewound.
If operation is not as specified, replace the belt assy.
20. INSTALL REAR SEAT 3 POINT TYPE BELT ASSY
INNER
(a) Install the floor anchor and belt with the bolt as shown in the illustration.
Torque: 42 N
m (430 kgf
cm, 31 ft
lbf)
NOTICE:
Make sure that the anchor part does not run onto the protru-
sion part of the floor panel.
21. INSTALL REAR SEAT 3 POINT TYPE BELT ASSY OUTER
(a) Install the belt with the bolt on the retractor side.
Torque:
7.5 N
m (76.5 kgf
cm, 66 in.
lbf) for front bolt
42 N
m (430 kgf
cm, 31 ft
lbf) for upper bolt
(b) Check the degree of tilt when the belt begins to lock the
ELR.
NOTICE:
Do not disassemble the retractor.
http://vnx.su

61±26
±
SEAT BELT REAR SEAT BELT (WAGON MODELS)
AVENSIS REPAIR MANUAL (RM1018E)
(1) Check that the belt does not lock within 15
of tilt in
all directions but locks with over 45
of tilt when
gently moving the retractor.
If operation is not as specified, replace the belt assy.
(c) Install the belt outer with the bolt on the floor anchor side. Torque: 42 N
m (430 kgf
cm, 31 ft
lbf)
NOTICE:
The check should be performed with the a ssembly
installed. (1) Check that the belt locks by pulling it out quickly af-ter installation.
If operation is not as specified, replace the belt assy.
(d) Check the ELR lock.
NOTICE:
The check should be performed with the a ssembly
installed.
(1) Check that the belt locks by pulling it out quickly af-ter installation.
If operation is not as specified, replace the belt assy.
(e) Check the fastening function of the child restraint system.
NOTICE:
The check should be performed with the a ssembly
installed. (1) Check that the belt cannot be pulled out any morebut rewinds after being pulled out fully.
(2) Check that the belt can be pulled out and rewound after the belt has been fully rewound.
If operation is not as specified, replace the belt assy.
22.INSTALL REAR SEAT ASSY (See page 72±21)
http://vnx.su